Question about 1994 Oldsmobile Cutlass Supreme

1 Answer

Need to know cylinder head bolt torque specs

I have 1994 Oldsmobile Cutlass Supreme with 3.4 Liter engine. I am replacing the head Gaskets and need to know the proper torque specs for the cylinder head gaskets. My manuel only gives the initial settings. I have the tighting sequice, need the foot pounds.

Posted by on

  • 1 more comment 
  • Anonymous Mar 13, 2014

    torque inch pound for head bolts of holden baina 2003?

  • Anonymous Mar 13, 2014

    need to know procedure to remove and replace head gasket on 2005 ford freestar

  • Anonymous Mar 19, 2014

    need torque spec

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 223 Answers

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): need to know cylinder head bolt torque specs - clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installedneed to know cylinder head bolt torque specs - clearpixel.gifper torque. clearpixel.gneed to know cylinder head bolt torque specs - clearpixel.gifi need clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Posted on Feb 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rocker arm pivot torque for olds cutlass 1987 307


Oldsmobile Torque Specs - GbodyOlds.com

www.gbodyolds.com/forum/showthread.php?754-Oldsmobile-Torque...
Feb 7, 2013 - 2 posts - ‎2 authors Oldsmobile Small-Block Engines Cylinder Head Bolts (1/2in. bolt) 130 ft. lbs. Cylinder Head ... Rocker Arm Pivot Bolt 25 ft. lbs. Rod Bearing ...

Rocker Arms - AutoZone

www.autozone.com/...Cutlass...1987.../Rocker-Arms/_/P-0900...

AutoZoneGM Cutlass RWD 1970-1987 Repair Guide ... To remove the rocker arms from the shaft, the nylon arm retainers must be removed. ... 7: Engine valve system, 260, 307, 350, 403 Oldsmobile built engines ... Unfasten the two bolts that attach the rocker arm pivot to the cylinder head. ... Torque the retaining bolts to 25 ft. lbs.

Dec 01, 2015 | 1987 Oldsmobile Cutlass Salon

1 Answer

What are the specs for the intake and head tork settings


cylinder head bolts are torque to yield bolts and are not recommend to torque them a 2nd time you should replace the bolts.

cylinder head blots.

step 1. 44 ft.lbs.

step 2. additional 95 degrees

lower intake bolts

115 in. lbs

upper intake bolts

18 ft. lbs

Apr 23, 2011 | 1997 Oldsmobile Cutlass Supreme

1 Answer

What is the torque settings on a 3.4 liter engine 94 camaro. replaced the heads and gaskets


Torque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

I hope this helps you and good luck

Mar 25, 2011 | 1994 Chevrolet Camaro

2 Answers

Need the torque settings for a '94 cutlass supreme sl 3.1 in reference to the cylinder heads I need the sequence and the torque if possible a diagram


Heres the diagram and specs for the cylinder head and also i have enclosed the torque specs for the intake and its tightening sequence, good luck and hope this is helpful, have a good day.
Cylinder head bolts. Step 1) tighten to 44 ftlbs.
Step 2) tighten an additional 95 degrees.

Lower intake bolts. Step 1) all bolts are tightened to 115 inch lbs.


Upper intake bolts.Step 1) all bolts tighten to 18 ft,lbs no diagram, start in the middle and work your way out going cris cross.johnjohn2_88.gifjohnjohn2_89.gif

Mar 19, 2011 | Oldsmobile Cutlass Supreme Cars & Trucks

1 Answer

Looking to replace head gasket for a 1971 oldsmobile cutlass supreme. need to know the pressure to put back in and also if there is any special order to the bolts when installing.


You can buy a Clymers or Chilton manual with the torque specs. and the tightening order. Generaly the bolts are tightened from the center outwards in two steps. First pass you snug all the bolts down, working from the middle bolts outward to the front and rear alternating between left and right side bolts.

Mar 14, 2011 | Oldsmobile Cutlass Supreme Cars & Trucks

1 Answer

Need torque sequence and specs for cylinder heads on a 1988 olds cutlass cierra with a 2.5 liter 4 cylinder engine


WELL ..THE FINAL PASS ON IT IS 65 FT LBS
YOU WANT TO DO THREE PASSES OF EQUAL INCREMENT'S LEADING TO 65 FT LBS
STARTING FROM THE CENTER TWO BOLTS AND WORKING YOUR WAY OUT IN A CROSS
SO BASICALLY THE FIRST PASS WOULD BE 21 FT LB.THE SECOND PASS WOULD BE ROUGHLY 43 LBS THEN THE FINAL PASS OF 65 FT LBS.


Dec 26, 2010 | 1988 Oldsmobile Cutlass Ciera

1 Answer

Head tourqe specs for 403 olds and bolt tightening


Fig. : Cylinder head torque sequence, 260, 307, 350 403 Oldsmobile built engines

5c04c01.jpg


On the V8, tighten the bolts, in the sequence illustrated, to 100 ft. lbs. When all bolts have been tightened to this figure, begin the tightening sequence again, and torque all bolts to 130 ft. lbs.

On V6's, tighten all head bolts in sequence to the following torques:
* All except bolts 5, 6, 11, 12, 13 and 14 - 100 ft. lbs.(19-135.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 41 ft. lbs. (19-55.5 Nm)
* All bolts except 5, 6, 11, 12, 13, and 14 - 142 ft. lbs. (19-192.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 59 ft. lbs. (19-80 Nm)

9fb545e.jpg

Hope this help (remember comment and rated this).

Mar 29, 2010 | 1984 Oldsmobile Cutlass

1 Answer

Where are the gaskets on a 1994 oldsmobile cutlass supreme


valve covers,1/2 hour each, oil pan 1 hour,head gaskets 7 hours,transmission pan1 hour ,intake 5 hours,or exhaust manifold gaskets.4 hours

Oct 23, 2009 | 1994 Oldsmobile Cutlass Supreme

2 Answers

What is the torque specs for a 1998 jeep Cherokee classic straight 6 4.0 liter? I am replacing the head gasket and need to find the lbs of torque. Thank you for any advice, pictures, etc.


Torque sequence ------------------ front | 12 8 4 1 5 9 13 | of | | engine | 11 7 3 2 6 10 14 | ------------------ Final torque must be reached in 3 equal steps Step 1: torque all bolts (except bolt 11) to 110 Ft/Lbs Step 2: torque bolt 11 to 100 Ft/Lbs Recheck final torque in sequence.

  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Disconnect the hoses at the thermostat housing.
  4. Properly relieve the fuel system pressure.
  5. Remove the cylinder head cover.
  6. Loosen the rocker arms.
  7. Remove the pushrods.

The valvetrain components must be replaced in their original positions.
  1. Remove the intake and exhaust manifold from the cylinder head.
  2. Disconnect the spark plug wires and remove the spark plugs.
  3. Disconnect the temperature sending unit wire, ignition coil and bracket assembly from the engine.
  4. Remove the accessory drive belt(s).
  5. Unbolt and set aside the power steering pump and bracket. Do not disconnect the hoses.
  6. Remove the intake and exhaust manifold assembly.
  7. If equipped with A/C, perform the following:
    1. Remove the compressor and position it aside with the lines attached.
    2. Remove the compressor bracket bolts from the cylinder head.
    3. Loosen the through bolt at the bottom of the bracket.

  8. Remove the alternator.
  9. Remove the cylinder head bolts, the cylinder head and gasket from the block.

Bolt No. 14 cannot be removed until the head is moved forward. Pull the bolt out as far as it will go and suspend in place by wrapping with tape.
  1. Discard the gasket. Thoroughly clean the head-to-block mating surface.
  2. Clean and inspect the cylinder head thoroughly. Refer to the engine reconditioning portion outlined later in this section.

To install:
  1. Coat a new head gasket with suitable sealing compound and place it on the block. Most replacement gaskets will have the word TOP stamped on them.

Apply sealing compound only to the cylinder head gasket. Do not allow sealing compound to enter the cylinder bore.

Oct 08, 2009 | 1998 Jeep Cherokee

Not finding what you are looking for?
1994 Oldsmobile Cutlass Supreme Logo

2,863 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...