Question about 1991 Cadillac DeVille

1 Answer

Instrument panel will not light up

Instrument panel will not come on at all

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Check the fuse box. or check the wiring. the ground may have disconnected.

Posted on Feb 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the instrument panel relay located?


There is no relay for the instrument panel. The dash lights and interior lights have fuses. The instrument panel itself is illuminated by the Central Power Module.

Jul 11, 2014 | 1990 Oldsmobile Toronado

1 Answer

I replaced the instrument cluster & head light switch on my 2001 buick century and the instrument panel and tail lights still do not work, what else can I do


Check 20Amp LP Park Fuse in Underhood Fuse Block (mounted to right strut tower) Check 15Amp Tail Lic. Lamp Fuse In IP Fuse Block.

Mar 15, 2014 | Buick Cars & Trucks

1 Answer

How do I remove dashboard to get to instrument panel to replace bulbs?


You will need a cross point screw driver

  • 1 Remove the two screws on the underside of the top of the trim panel surrounding the dash and instrument panel.
  • 2 Pull the trim piece off the dash.
  • 3 Remove the four screws that hold the instrument panel in the dashboard using a cross point screwdriver.
  • 4 Slide the dashboard instrument panel forward and disconnect the electrical connector from the back of the dashboard.
  • 5 Turn the instrument panel over.
  • 6 Turn the base of the dashboard light bulb counterclockwise to unlock it from the instrument panel and pull it out of the panel to remove it.
  • 7 Insert a new light bulb into the back of the panel, and turn the bulb clockwise to lock it into the panel.
  • 8 Plug the electrical connector back into the instrument panel and slide the panel back into the dashboard.
  • 9 Secure the panel with the factory mounting screws and replace the trim and trim-mounting screws using a screwdriver.
  • Nov 23, 2010 | 1999 Toyota Sienna

    1 Answer

    Cannot find heater blower in 1999 ford taurus


    It's hiding deep behind the right side dash. See instructions from autozone.com below.

    1997-99 Models

    1. Disconnect the negative battery cable.
    2. Disengage the instrument panel insulator from the instrument panel.
    3. Detach the wiring connector at the blower motor.
    4. Unsnap the instrument panel upper finish panel from the instrument panel.
    5. On vehicles equipped with autolamp, Detach the electrical connector from the light sensor amplifier.
    6. Unsnap and remove the instrument panel finish end panel from the right side of the instrument panel.
    7. Remove the 3 screws retaining the instrument panel to the upper cowl top panel.
    8. Remove the 2 screws at each right side of the instrument panel.
    9. Remove the 3 screws retaining the blower motor to the evaporator housing.
    10. Pull the instrument panel away from the cowl and remove the blower motor from the A/C evaporator housing.
    11. If required, separate the blower motor wheel from the blower motor by removing the retainer from the blower motor shaft and sliding the blower motor wheel off the blower motor shaft.

    To install:
    1. If the blower motor wheel was removed, align the flats on the inside diameter of the wheel hub with the flat surface on the blower motor shaft and slide the blower motor wheel onto the blower motor shaft. Install a new blower motor wheel retainer onto the shaft.
    2. Install the blower motor and wheel assembly into the evaporator housing and firmly tighten the 3 retaining screws.
    3. Reposition the instrument panel and install the 2 screws at each right side of the instrument panel.
    4. Install the 3 screws retaining the instrument panel to the upper cowl top panel.
    5. Install the instrument panel finish end panel to the right side of the instrument panel.
    6. On vehicles equipped with autolamp, Attach the electrical connector to the light sensor amplifier.
    7. Snap the instrument panel upper finish panel to the instrument panel.
    8. Attach the wiring connector at the blower motor.
    9. Engage the instrument panel insulator to the instrument panel.
    10. Connect the negative battery cable. Check for proper blower motor operation.

    Nov 01, 2010 | 1999 Ford Taurus

    1 Answer

    Dashboard lights burning out, down to 1 illuminating tach, speedo, gas gauge. How complicated to replace?


    one hour job. find bulb part number in bulb chart in owner manual.

    go here for villager help.

    http://groups.yahoo.com/group/villagerquest/

    Section 13-01B: Instrument Cluster — Conventional 1996 Villager Workshop Manual
    REMOVAL AND INSTALLATION Instrument Panel Finish Panel Removal
    1. Disconnect the battery ground cable (14301).
    1. Block the wheels (1007) to prevent the vehicle from moving.
    1. Turn the ignition switch (11572) to the OFF position.
    1. Shift the transmission range (TR) selector to MANUAL LOW (1).
    1. Tilt the steering wheel (3600) to the lowest position, if equipped with a tilt wheel.
    1. Remove the two instrument panel finish panel screws.
    1. Remove the instrument panel finish panel (044D70) enough to access the switch electrical connectors.
    1. Disconnect the rear windshield wiper/washer switch electrical connector.
    1. Disconnect the heated back window and light switch electrical connector.
    1. Disconnect the emergency warning switch electrical connector.
    1. Disconnect the SECURITY indicator light electrical connector.
    1. Disconnect the speed control on/off (CRUISE CONT. ON/OFF) switch electrical connector.
    1. Disconnect the headlamp switch electrical connector.
    1. Disconnect the autolamp/light switch rheostat resistor electrical connector.
    1. Remove the instrument panel finish panel with the switches attached.
    -------------------------------------------------------------------------------------------------
    Instrument Cluster
    Removal
    1. Disconnect the battery ground cable (14301).
    1. Block the wheels (1007) to prevent the vehicle from moving.
    1. Turn the ignition switch (11572) to the OFF position.
    1. Shift the transmission range (TR) selector to MANUAL LOW (1).
    1. Tilt the steering wheel (3600) to the lowest position, if equipped with a tilt wheel.
    1. Remove the two instrument panel finish panel screws.
    1. Remove the instrument panel finish panel (044D70) enough to access the switch electrical connectors.
    1. Disconnect the rear windshield wiper/washer switch electrical connector.
    1. Disconnect the heated back window and light switch electrical connector.
    1. Disconnect the emergency warning switch electrical connector.
    1. Disconnect the SECURITY indicator light electrical connector.
    1. Disconnect the speed control on/off (CRUISE CONT. ON/OFF) switch electrical connector.
    1. Disconnect the headlamp switch electrical connector.
    1. Disconnect the autolamp/light switch rheostat resistor electrical connector.
    1. Remove the instrument panel finish panel with the switches attached.
    1. Remove the four instrument cluster screws.
    2. Remove the transmission range indicator (7A110) from the instrument cluster (10849).

    Jan 13, 2010 | 1995 Mercury Villager

    1 Answer

    Instrument panel lights will not work after new battery was installed. Previously, When door was opened one could hear static noise and flickering of instrument panel lights. Battery was checked and was no...


    Hi 1987 Honda Civic lihgts on instrument panel. New Battery. and replaced blower unit but lights on panel not working. I am yet to install stereo unit which was taken out by previous owner - very roughly ! Wondering if not having stereo will effect instrument panel lights. Cheers Steve

    Nov 22, 2009 | Chevrolet Impala Cars & Trucks

    1 Answer

    A digram for the factory wireing for the radio


    This color code works for 87-93 mustang factory radio; it might work on yours as well. I'm not sure if it has the same fuses though.

    Radio Connector:

    Light Green / Yellow - Hot at all times (Fuse 8)
    Yellow / Black - Hot in ACC or Run (Fuse 11)
    Light Brown / Red - Goes to instrument panel dimming rheostat (Fuse 4)
    Red - Ground
    White / Purple - Hot in ACC or Run (Fuse 11)

    Speaker Connector:

    White / Light Green - (+) Right Instrument Panel & Door Speaker
    Dark Green / Orange - (-) Right Instrument Panel & Door Speaker
    Brown / Pink - (+) Right Rear Speaker
    Pink / Light Brown - (-) Right Rear Speaker
    Pink / Light Green - (+) Left Rear Speaker
    Tan / Yellow - (-) Left Rear Speaker
    Light Brown / White - (+) Left Instrument Panel & Door Speaker
    Orange / Light Green - (-) Left Instrument Panel & Door Speaker
    Hope this helps.

    Aug 15, 2009 | 1991 Ford Econoline

    1 Answer

    Need color code diagram for sterio


    I'm not sure what year you have but this color code works for 87-93 mustangs.

    Radio Connector:

    Light Green / Yellow - Hot at all times (Fuse 8)
    Yellow / Black - Hot in ACC or Run (Fuse 11)
    Light Brown / Red - Goes to instrument panel dimming rheostat (Fuse 4)
    Red - Ground
    White / Purple - Hot in ACC or Run (Fuse 11)

    Speaker Connector:

    White / Light Green - (+) Right Instrument Panel & Door Speaker
    Dark Green / Orange - (-) Right Instrument Panel & Door Speaker
    Brown / Pink - (+) Right Rear Speaker
    Pink / Light Brown - (-) Right Rear Speaker
    Pink / Light Green - (+) Left Rear Speaker
    Tan / Yellow - (-) Left Rear Speaker
    Light Brown / White - (+) Left Instrument Panel & Door Speaker
    Orange / Light Green - (-) Left Instrument Panel & Door Speaker
    Hope this helps.

    Jun 19, 2009 | Ford Escort Cars & Trucks

    1 Answer

    No Instrument Panel Lights


    The instrument panel has an internal short.
    This is very common failure with the instrument cluster. You need to take to the dealer for repairs.

    Mar 22, 2009 | 2000 Dodge Caravan

    1 Answer

    98 honda accord panel lights will not turn on


    Did you check the dimmer to switch? This is for a 2000 Honda Accord but this may help you: If your instrument lights have burnt out on your 2000 Honda Accord.... You may have another problem!!! While the dealer fixes this recall, they should replace your burnt out bulbs. 2000 Honda Accord Recall ID from NHTSA: 04V256000 Auto Recall Date: 06/07/2004 Vehicle Component: INTERIOR LIGHTING Estimated Vehicles Affected: 19572 2000 Honda Accord Defect Summary: ON CERTAIN PASSENGER VEHICLES, THE DIMMER CONTROL FOR THE INSTRUMENT PANEL LIGHTS COULD FAIL DUE TO HEAT BUILDUP. Defect Consequence: IF THIS OCCURS, THE INSTRUMENT LIGHTS MAY FAIL AND, AT NIGHT, THE DRIVER MAY NOT BE ABLE TO SEE THE INSTRUMENT PANEL GAUGES, SUCH AS THE SPEEDOMETER. Remedy: DEALERS WILL REPLACE A MULTIPLEX CONTROL UNIT FOR THE INSTRUMENT PANEL LIGHTS. OWNER NOTIFICATION BEGAN JUNE 16, 2004. OWNERS SHOULD CONTACT HONDA AT 1-800-999-1009. Notes: AMERICAN HONDA MOTOR CO., P36

    Nov 25, 2008 | 1997 Honda Odyssey

    Not finding what you are looking for?
    1991 Cadillac DeVille Logo

    Related Topics:

    76 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cadillac Experts

    yadayada
    yadayada

    Level 3 Expert

    60960 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a Cadillac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...