Question about Cadillac STS

Open Question

Po340 po1320 1999 nissan sentra 1.6 motor

What could be the problem i put dist and crank sensor in and still wouldn't start

Posted by on

  • Jeremy Reddick
    Jeremy Reddick May 11, 2010

    Have you tried these?
    P1320 IC 4X Reference Circuit Intermittent
    P0340 Camshaft Position Sensor A Circuit Malfunction (Bank 1 or Single Sensor)


×

5 Suggested Answers

  • 1 Answer

SOURCE: 1999 nissan sentra gxe headlight problem

I switched one of the new bulbs with a working older bulb, and the problem went away. weird...

Posted on Apr 24, 2009

  • 1 Answer

SOURCE: 1996 Nissan Sentra doesn't have sparks

Hi , the car was running before ?

if was your trouble is the timing marks are off the

right position

Posted on May 30, 2009

  • 8 Answers

SOURCE: P0335 CRANK POSITION SENSOR A CIRCUIT MALFUNTION

crank sensors are usually located in/near the distributor.

Posted on Jun 07, 2009

  • 54 Answers

SOURCE: 2002 Nissan Sentra Loses Power

SERVICE IT .....OIL PLUGS, AIR ,FUEL AND OIL FILTERS GET TROTTLE SENCOR AND THE MASS AIR FLOW SENCOR CHECKED

Posted on Jun 29, 2009

glamarre82
  • 140 Answers

SOURCE: DTC - PO340, PO325

Replace both

Posted on Jul 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

95 nissan altima po340


PO345 is the cam shaft positioning sensor and PO325 is the knock sensor. Check your starter and your battery.

Apr 05, 2014 | 1995 Nissan Altima

1 Answer

Nissan sentra 200SX cranks over but won't start


check fuel pump, fuel pump fuse, distributor,and ignition coil please. then you will need to check crank position sensor.(to do this you need to find factory service manual)

Nov 23, 2011 | 1996 Nissan 200SX

1 Answer

Why would a 2003 nissan occasionally not crank and after cranking stall out while driving?


if crank or cam sensor fails then it will cause hard time starting, shut off while driving, here are the fault codes--po340 is camshaft sensor. have car scanned at any auto parts place they will scan it for free. these two things will cause a problem code.

Jan 15, 2010 | 1998 Nissan Pathfinder

1 Answer

2006 sentra with 93,000 miles on it and it would not turn over yesterday. today was told the it cranks up fine. was told needs cam and crank sensors. does that sound right?


If starter was not engaging yesterday could be a starter or battery starting to go bad could have that problem again, cam and crank sensor will not stop the starter from turning the engine, the motor will not start up and just keep cranking.Hope this was very helpful.

Dec 29, 2009 | 2006 Nissan Sentra

1 Answer

Car will not run, got two DTC's po340 and po325


The po340 is a cam sensor code ,po325 is a crank sensor code>THE crank if it goes bad will through both codes,and also the car will not start.You will have no spark or injector pulse.So have your crank sensor checked:)

Aug 06, 2009 | 1998 Nissan Maxima

1 Answer

P0335 CRANK POSITION SENSOR A CIRCUIT MALFUNTION


crank sensors are usually located in/near the distributor.

Jun 07, 2009 | 2003 Nissan Sentra

2 Answers

Where is the camshaft sensor on 97 nissan sentra


I am not sure where in a Sentra, but in a Quest 1993-02, it is in the distributor (integral). Common problem with Quest is that brown dust covers optical sensor under slotted wheel under rotor. If dust, the bearing is failing and you need new distributor. Clean optical sensor and see if it starts and runs. Get dist. on ebay.

report back on progress.

May 29, 2009 | 2002 Nissan Altima

2 Answers

02 nissan sentra


Its possible, that you crank angle sensor is failing. Also, that vehicle had a issue with the ECM/computer. Nissan put a set of foams inside of the ECM box to prevent the ECM from movement, however the glue that they used to attach the foams was causing the ECM to fail. The vapors from the glue would eat up vital circuits inside the computer causing failuer. I would go to your local dealer and provide them with your VIN nujber. With the VIN number, thay can check to ysee if the foam campaign has been doen and also the crank and cam angle sensor camaign. Nissan volunteraly replaced cam and crank angle sensors if the VIN number matches the campaign. Your ECM/computer is covered for 8years or 80000 miles. We are also starting to see timing chains getting stretched causing running issues, but you will have a "check engine light on" for cam angle sensor circuit. Anyhow, go to your local friendly NIssan dealer and have them run your VIN number to see if you have any open campaigns (crank and cam sensors, ECM foam etc.) Good luck and let me know what you find.

Nov 03, 2008 | 2002 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

200 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

63456 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...