Question about 1995 Pontiac Grand Am

1 Answer

95 pontaic grand am

My turning signal switch will stay back to keep the high beams on. and low beams willn't work also brake lights willn't stay on.... and fuses keep blowing for that light.

Posted by on

  • yadayada
    yadayada May 11, 2010

    have u replaced the combination switch, it must be shorted.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 87 Answers

Your problem is attributed to the turn signal switch , both the left and right turn signals go thru the switch as well as the brake lights , it is a common problem with these cars.

Posted on Feb 06, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a problem with the low beams on my headlights. The high beams works just fine. All of the other lights(turn signal, emergency lights, etc.) work except for the low beams.


Check the fuses first. then replace the turn signal switch if all fuses are good. All the lights run threw it, except the high brake light on the rear.

Jan 01, 2015 | 2003 Ford Escape

1 Answer

My 1984 chevrolet silverado high beams lights works and low beam lights, turning lights, emergency light and brakes lights don't work. I need help!


Those lights are on different circuits. The high and low beam lights are powered thru the headlight switch, the turn signals, brake, and hazards go thru the turn signal switch.
I would want to know if each circuit has power at the switch that controls it.

Jun 28, 2013 | Cars & Trucks

1 Answer

No break lights, high beams, or turn signal lights


Do they work intermittently? Do your low beams go out sometimes when you put on turn signal? Do hazards work sometimes and if you play with switch they work off and on? I just had a problem with headlights would go off if I put on turn signal and if I jiggled the turn lever they would come back on and had trouble with all light working intermittently, brakes, turn and hazard. It was a Turn signal switch problem.The contacts in the switch were bad, all corroded and green when I took it apart. I know you wouldn't think this would affect brake lights but hey all run through this switch because of hazards and high beams. I got a new switch from dealer and all is working great now. Here's a link a link I used for switch replacement instructions. http://www.jeepforum.com/forum/f11/write-up-replace-turn-signal-switch-97-xj-620147/
If it isn't a fuse or wiring issue I would look into the switch.

Apr 02, 2011 | 1997 Jeep Wrangler

1 Answer

My light problem is i have low beam on right side no low on left side i turn highs on and right side goes out and high on left turns on then when back to lows beams and i pull turn signal to flash high...


If you have separate bulbs for the low and high beams(4 light system), if you pull the turn signal and hold it, all 4 lights will stay on until you release the turn signal. You need to replace the bright bulb on the right side and the low bulb on the left side. If your headlights only have one bulb on each side, then you will have to replace both of them to get everything to work.

Jan 04, 2011 | 2000 Ford Mustang

2 Answers

My truck is actually a '95 C1500 but I understand that they were the same model from 88-98. I have 2 problems - both electrical. On a recent trip, I lost both low beam headlights at the same time. ...


There could be a fuse for each low beam light either under the hood or under the dash. If not, then prob both low beams are bad.

If you have daytime run lights, the following may be of help.

There is a daytime running light module that controls both low beams and the daytime running lights. The low beam bulbs may be OK. The high beams will work fine as they are not controlled through the module.

It may be possible to disable the daytime run lights by cutting the yellow wire going into the module and then connecting it to ground. Tape off the other end.


This will help. Thanks please keep updated.please do rate the solution positively .thank you for using fixya

Mar 03, 2010 | 1998 Chevrolet C1500

1 Answer

Head lights not working


check your relays, they are like big fuses in your engine compartment, if your low beam and high beam relays are the same model, switch them and see if this enables low beams and disables the high beams. if it not the relays, or fuses, then it is probably your wiring harness, an expensive repair.

Oct 18, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Pontiac Grand Am Logo

172 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...