Question about 2001 Hyundai XG300

1 Answer

About the rust in the silver coated part of the bike

Hi friends
i am having avenger oil cooled 200 cc bike and the problem which i faces is that the silver coated part of my bike is being rusted ,,, how can i stop it plz sugg

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

Use Mothers Chrome Polish to get the Rust back down to the Tiny Speck that Started it and Use Clear Finger Nail Polish on the Tiny Spots that cause the Rust and it will stop it. You will need to Replace the Nail Polish every Now and then. Please Rate My Response! Thanks!

Posted on Feb 06, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Sludge in cooling system


Leaking head gaskets can and do cause this, the combustion gases are very corrosive and rusts the heck out of the cast iron.

Apr 20, 2017 | 1989 Ford F 150

1 Answer

Gas cap light is on in my 2009 dodge avenger


basically what you need to do is to check the oil gascap see if it has any type of dirt or anything under, if so just clean it off. the gascap should be on top of engine where it says OIL. or the gas cap could be rusted and may have to be replaced

Feb 20, 2013 | Cars & Trucks

1 Answer

Rust build up in the crank shaft


I'm not sure you understand what the crank shaft is. It is an internal rotating part of the engine. Although it could possibly rust, it would be very difficult to see without disassembling the engine completely. In addition, it is normally covered with a fine coat of oil, so it would not rust unless all the oil was removed and the engine sat for a number of weeks.

If you could provide more information, we could probably diagnose your problem.

However, rust in and of itself is not a problem and should not prevent a car from running.

Jan 29, 2013 | 2007 Chevrolet Uplander LS Minivan

2 Answers

1997 dodge avenger 4 cylinder. The car been having some misfires, especially when it sat on the sun for some time. I was adviced to try to replace the crankshaft position sensor, I did and the problem went...


It's a proximity switch so it shouldn't be subject to wear. Oil doesn't interfere with the working of the proximity switch. Check the contacts where the lead connects. Make sure the connector can't move with vibration.

Mount the old switch again - when it's ok again for some time it's most likely the cabling not the sensor switch itself

Jun 26, 2011 | 1997 Dodge Avenger

4 Answers

This is a general question: New brake rotors and drums are usually delivered with some kind of antirust coating. It can be a thin layer of oil, or some primer type paint. I was told, before installing...


Remove the oil or any other coating on the surface's where the brake shoes or pads make contact. This area should be cleaned before installing brake shoes/pads. As for the sand paper for the surface, it is a good idea to lightly sand the contact surface, but just lightly. What is also important is applying anti squeal to the backside (metal side) of the brake pad before installing, and also apply a small bit of grease where the brake shoe hits the backing plate (high spot on the backing plate, there is most likely four raised areas total for each side) on the rear brake assembly....just a small amount will keep the rears from making noise also.

Feb 17, 2011 | Chrysler Neon Cars & Trucks

1 Answer

Rear brake drums wii not slide off


then they are rusted to the hub face, spray rust removing penetrating oil all around the face of the drum into the wheel lug holes and let it set, they strike the face of the drum with a brass faced hammer until the rust bond is broken

Sep 22, 2010 | 1997 Ford Contour

1 Answer

96 dodge avenger automatic 2.4 liter i can drive


Check the transmission oil cooling radiator [and fan(s)] to check for proper cooling--blow out the radiator fins with compressed air. Check the color of the transmission fluid to make sure that is not being contaminated.

Nov 03, 2009 | 1996 Dodge Avenger

1 Answer

White smoke Air Cooled Suzuki dr 200 with oil next to carb


usaually white smoke means you're burning too much oil.

Jun 26, 2009 | 2003 Chrysler Sebring

1 Answer

Fouling spark plugs with black coating not oil


I am assuming the mitsubishi 2.5? Most likely it is an oxegyn sensor problem. If they are not reading like they should, it just floods out the car. Could also have a stuck open injector (stays on all the time).

Mar 11, 2009 | 1996 Dodge Avenger

Not finding what you are looking for?
2001 Hyundai XG300 Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...