Question about 2005 Dodge Ram 1500

2 Answers

2005 Dodge 1500 code p0404 EGR valve.

Appreciate your help located the EGR valve on my 2005 Dodge 1500 4.7 liter and any direction availble on how I replace it?
Thanks!

Posted by on

  • 6 more comments 
  • bobnva Feb 07, 2009

    At a local auto parts store I was told that the EGR valve is emissions related and under Federal law would be covered by mandatory 5 year 50,000 mile warranty. Anyone know how I can verify this?

  • baldeagle67 Feb 24, 2009

    I have my check engine light on and the code that I'm getting is P0404 and I would like to know what this code is so I can fix the problem and can you tell me where its located. thank you.

  • Anonymous Mar 12, 2014

    how to replace hydraulic valves

  • Anonymous Mar 13, 2014

    2005 dodge ram 1500 wort start has code po685

  • Anonymous Mar 14, 2014

    How to repair 2008 dodge avenger egr valve

  • Anonymous Mar 16, 2014

    location of pvc valve

  • Anonymous Mar 28, 2014

    P0404

  • Anonymous Mar 31, 2014

    egr nox

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,596 Answers

The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,

  1. Remove electrical connector (5) at top of EGR valve solenoid.
  2. Remove tube mounting bolt (1) at intake manifold.
  1. Remove two bolts (4) connecting EGR tube (1) to valve assembly.
  2. Remove gasket located between EGR tube flange and EGR valve assembly.
  3. Remove two EGR valve mounting bolts (5).
  4. Separate valve assembly (3) from engine.
  5. Remove and discard metal gasket located between cylinder head and valve assembly.
INSTALLATION
  1. Clean area at rear of left cylinder head where it joins base of EGR valve.
  2. Clean EGR tube where it joins EGR valve.
  3. Position new gasket between EGR valve and cylinder head.
  4. Position EGR valve to cylinder head. Install and tighten two bolts (5). Refer to Torque Specifications.
  5. Position new gasket between EGR tube flange and EGR valve assembly.
  6. Position EGR tube (1) to side of EGR valve and into intake manifold.
    1. Install EGR tube flange bolt (1) at intake manifold. Tighten bolt. Refer to Torque Specifications.
    2. Connect electrical connector (5) to top of EGR valve solenoid (2).Do a final tightening of two EGR tube bolts (4). Refer to Torque Specifications

Posted on Feb 05, 2009

  • Ronnie Wilson Jul 06, 2009

    About the Warrentee on Emissions, YES In Cailfornia But Each State has there own Laws that,

    Dealers Must Abide By on Emissions.



    I will Try and email you the Illistrations for EGR

×

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,902 Answers

There are two bolts and a nut on the back that removes the flared fitting. After that you just install the bolts and the flare back on and away you go

Posted on Feb 05, 2009

  • Jeremy Reddick
    Jeremy Reddick Feb 07, 2009

    YEs that is true it is to be covered unless you live in the state of California

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the EGR selonoid fuse on a 05 Dodge Magnum 5.7L?


There is no solenoid fuse , the PCM - engine computer supply's the control voltage . You have a wiring problem ! http://www.obd-codes.com/p0404 Engine Code P0404 EGR Position Sensor Performance

Feb 25, 2016 | 2005 Dodge Magnum RT

1 Answer

Stalling wont idle


  • egr valve
  • egr sensor
  • cam shaft sensor
  • barometric pressure sensor (map sensor)
vacuum leak somewhere, out of time, broken timing belt or missing teeth.

Dec 12, 2013 | Cars & Trucks

1 Answer

2004 dodge 1500 4 x 4 the engin mlight came on and the code is p0404. What does P0404 stand for?


SYMPTOM
P0404-EGR POSITION SENSOR PERFORMANCE

WHEN MONITORED
Engine running.

SET CONDITION
The EGR flow or valve movement is not what is expected.

POSSIBLE CAUSES
- Good trip equal to zero
- Excessive resistance in (F856) 5-volt supply
- (K34) EGR sensor signal circuit shorted to ground
- EGR assembly
- (K35) EGR solenoid control circuit
- Intermittent condition
- (K34) EGR sensor signal circuit open
- (K34) EGR sensor signal circuit shorted to ground
- (K900) sensor ground circuit open
- EGR assembly (ground)
- PCM
var classElements = new Array(); var node = document; var tag = 'a'; var els = node.getElementsByTagName(tag); var elsLen = els.length; var pattern = new RegExp("(^'\\s)specs_note(\\s'$)"); for (i = 0, j = 0; i

May 28, 2011 | 2004 Dodge Ram 1500

1 Answer

I have a 2005 6.0 liter powerstroke f-350 with codes P0404 and P0405, I have tried cleaning the egr valve and reset the code worked fine for a little while then the codes came back.


I have a 2005 6.0 liter powerstroke f-250 with P0404 and P0405, I have tried cleaning the egr valve and reset the code worked fine for a little while then the codes came back. Any Idea what's going on?

Jun 15, 2010 | 2003 Ford F150 Regular Cab

1 Answer

2005 dodge caravan diagnostic code p0404, please explain and do i replace the egr valve?


p0404 is-egr flow ckt range/performance, check egr, remove from vehicle and clean out carbon from valve and where it mounts on engine. also check the wireing connector and wire to valve. if this dosnt work, replace valve,

Apr 23, 2010 | 2005 Dodge Caravan

1 Answer

Where is the egr valve on a 2005 dodge 1500 5.7L


The electronic EGR valve and solenoid assembly (3) is attached to the front of the right cylinder head (1). An exhaust gas routing tube connects the EGR valve to the intake manifold.

2efe0f8.gif

Disconnect electrical connector (1) from EGR solenoid (2). Remove two bolts (3) connecting EGR tube (4) to valve assembly. Remove gasket located between EGR tube flange and EGR valve assembly.

Remove two mounting bolts (2). Separate valve assembly (3) from cylinder head (1). Remove and discard metal gasket located between cylinder head and valve assembly.
The new EGR valve will come with a new metal gasket. You can reuse the smaller gasket for the metal pipe going to the egr valve as long as its not damaged.

TY for using Fixya; remember rated this post.

Apr 14, 2010 | 2005 Dodge Ram 1500

1 Answer

2005 dodge caravan p0404 error code mechanic replaced egr valve code still on


Code may just need to be cleared out/ or there may be carbon in the intake manifold ,/you can try some carbon cleaner like Seafoam or concentrated injector cleaner /may clean it up for you .bring it back and have them read & clear codes. Hope this is helpful, feel free to ask if you would like any further assistance. Thank You .

Apr 05, 2010 | 2005 Dodge Caravan

3 Answers

I have a 2005 dodge ram 1500 4x4 4.7 liter with 81,000 miles my check engine light came on and i get codes P0404 and P0405 what component do i need to replace to fix the problem ? also it seems to be a...


p0404 is EGR valve. you can try freeing it up with B12, I did that to my 2000 Expedition and it has worked for over a year so far p0405 EGR position sensor input below the minimum acceptable voltage range (shorted low) Actions
  • Clean or replace the EGR
  • Replace the DPFE
  • Clean the throttle body
  • Clean the MAF - use electrical contact cleaner and be gentle

Oct 14, 2009 | Dodge Ram 1500 Cars & Trucks

2 Answers

P0404 err code and it feels like engine serges 45 to 55 mph


Check your EGR valve hose for leaks/cracks etc, remove wiring connector & clean all contacts. Remove battery terminals before you start, but make sure you don't have to recode your anti-theft, or code your stereo, without proper info ready at hand. If your not sure, leave them on, but make sure key is off. Try again now, and see if code returns, if it does, get a new gasket for EGR valve, remove it & clean it thoroughly with throttle body spray cleaner, and re-install. It should be located close to throttle body, with 2 bolts attaching it to intake manifold. Near TP sensor & IAC motor. Try again, but see if you can get codes erased prior to, or immediately after, and see what happens.

Apr 25, 2009 | 2005 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

4,049 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...