Question about 2005 Ford F 350 Super Duty

2 Answers

Heated seat doesn't work

Heated seats don't work and I don't have access to wiring schmatic. Any ideas or imput
Thanks in advance.

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 60,769 Answers

HERE IS THE FUSE INFO FROM YOUR OWNERS MANUAL.
FUSE #21 20A* Heated seats
PASSENGER COMPARTMENT FUSE BOX LOCATED BEHIND TRIM PANEL TO THE LEFT OF STEERING COLUMN.

Posted on Feb 05, 2009

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 26 Answers

You probably blow the fuse call up ford give them all the information about you car and they will tell you what kind of fuse you need.

Posted on Feb 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Both heated seats and mirrors don't work


Not exactly.
According to the wiring diagrams, the heated seats are controlled by several fuses and two modules, plus two relays, along with input from the HVAC module. There is a module and a relay for each seat heater.
The mirrors are controlled by several other fuses and modules.
You may need a shop manual to trace the circuits.
All of the fuses involved are in the box in the engine compartment.

Sep 19, 2012 | 2005 Ford F 350 Super Duty

1 Answer

Where is the fuse for the heated seats in a 2007 jeep grand cherokee laredo?


Remove the ignition key. Unplug the HSM (heated seat module). It is under the passenger seat. You can easily accomplish this with the seat all the way back. Wait a few seconds they plug it back in. Start the engine. Turn the seats on. If the indicator lights come on for 2 seconds and then go out, further diagnostics is required. Hopefully they'll stay on and the seats will be working fine.

Thanks,
Ron

Feb 12, 2012 | Jeep Grand Cherokee Cars & Trucks

1 Answer

My 2004 Chevrolet 3/4 ton truck heated seats come on without turning on the switch. Is there a fuse or a wire I can disconnect? It is 108 degrees here in Austin, TX. I don't need heated seats. Thanks


THEIR SHOULD BE A MODULE UNDER THE SEAT TO UNPLUG .THEIR HAS BEEN PLENTY OF PROBLEMS WITH THIS HEATING ISSUES SOME WORK SOME DONT .MAYBE TAKE THE DOOR PANEL OFF AND UNPLUG THE SWITCH FROM THE BACK SIDE

Aug 05, 2011 | 2004 Chevrolet Silverado 2500HD

1 Answer

The driver's side heated seat won't turn off on my 2003 Mecury Moutaineer. Also, how do I change my cabin filter?


Your vhicle build date is on a blue sticker on the driver door or door frame. If not there, check other doors.
The heated seat Module is under the seat. You can unplug the connector on it or the heated seat switch to shut it off. I supect the module is bad. get one used from car-parts.com. The cabin air filter is under the leaf screen at the base of the windshield. Remove wiper arms and leaf screen for access. Please rate, thanks. Principles of Operation - Heated Seats - Vehicles Built 03/2002 Onward
NOTE: Two heated seat modules are used, one for vehicles built up to 03/2002 and one for vehicles built 03/2002 onward. The modules are not interchangeable.
The driver and passenger heated seats share a common battery and ignition feed. A shared ground source supplies the heated seat control switches. When the heated seat control switch is pressed with the ignition switch in RUN or START, a momentary ground signal is sent to the heated seat module. The heated seat module then supplies power to the heating element circuit. The cushion element and seat backrest element are wired in series and powered by the same output. The heated seat module also will ground the separate indicator circuit at the dual automatic temperature control (DATC) module display panel to indicate an ON state. The heated seat module will remain on until the heated seat control switch is pressed and a momentary voltage signal is received, or until 10 minutes expire. If the ignition source is removed from the module, the heated seat module will enter an OFF state and will not return to ON until the switch is once again pressed with the ignition switch in RUN. The heated seat module is designed to heat the seat to 37.5?C (99.5?F) and maintain the temperature until time-out or switched off. This temperature is maintained by the heated seat module monitoring the temperature sensor located in the seat cushion element, and adjusting the current flow to the heating elements.
--------------------------------------------------------------------------------------------------------------------------------

May 22, 2011 | 2003 Mercury Mountaineer

2 Answers

Heated seats in 2007 Lincoln MKX not working. I puch the button to turn them on and they light up for a second then go off. What would be the cause and solution. If it was a major problem would effect...


Help anybody?
I have a 2010 Lincoln MKX with heated and cooled front seats. However, when I try to turn them on (85% of the time) they don't work. Primarily when it's cold the heated seats won't stay on... The light turns on for a fast count of 1-5 and then turns off. This has happened since the car was new and I've had it into the dealer 4 times to have it fixed (with no resolve). In their defense they suggest it's fixed each time because they test the heated seats when the vehicle is warm in the shop. Unfortunately, this is nearly the only time it stays on.
I would love to recommend a suggested fix to the dealer as they don't seem to be able to repair it... Any ideas???

Mar 14, 2011 | 2007 Lincoln MKX AWD

1 Answer

Hummer h3 2006 - heated seats not working, already checked fuse and all wiring is plugged in, any idea what else could be the problem


check fues 53 heated seat swichs, wire undwe dash rubed against a bracket, i brought to dealer

Jan 23, 2011 | 2006 Hummer H3

1 Answer

My power seat stopped working in my 2003 Yukon XL. The heated seats stopped working as well.


Try this remove the ckt breaker for the power seats the ckt breaker is located in the fuse box inside down by the drivers left foot. leave breaker out for about 10 seconds then reinstall it and see if the seat starts moving. If it does there is a reprogram for this and needs to be done by a dealer or someone who has access to be able to reprogram your vech.
several things could cause your heated seats to not work. If the seat and heated seat seat stopped at the same time could be the reprogram could fix it. If the heated seat quit working at a differant time it could be the seat heater element. get a schematic of the heated seat and ohm the wires for the element. If either element tests open then the element will need to be replaced. You might as well replace both of them at the same time since the seat covers have to come off to replace the seat heaters.(back and bottom ) If one element is bad then both heaters quit working.

Feb 20, 2010 | 2003 GMC Yukon XL

1 Answer

2002 Grand Cherokee Heated Seats don't work


I will post it in 2 different posts because its too long DB

HEATED SEAT SYSTEM
Individually controlled driver and passenger side electrically heated front seats are available factoryinstalled optional equipment on this model, when it is also equipped with the power seat option. The heated seat system allows both the driver and the front seat passenger the option to select one of two seat heating ranges, Low or High, or to turn the individual seat heaters OFF using the heated seat switches located in the center lower bezel near the bottom of the instrument panel center stack. The heated seat switch circuit operates on ignition switched battery current supplied through a fuse in the junction block, only when the ignition switch is in the ON position.

The heated seat system consists of the following components
  • Heated seat elements
  • Heated seat sensors
  • Heated seat module (or memory heated seat module)
  • Heated seat switches.
The heated seat system also relies upon resources shared with other electronic modules in the vehicle over the Programmable Communications Interface (PCI) data bus network. The PCI data bus network allows the sharing of sensor information. This helps to reduce wire harness complexity, internal controller hardware, and component sensor current loads. At the same time, this system provides increased reliability enhanced diagnostics, and allows the addition of many new feature capabilities. For diagnosis of these electronic modules or of the PCI data bus network, the use of a DRB scan tool and the proper Diagnostic Procedures are recommended.

The electronic modules that may affect heated seat system operation are as follows:
  • Body Control Module (BCM) - Refer to Body Control Module in Electronic Control Modules for more information.
  • Heated Seat Module (HSM) - Refer to Heated Seat Module in Electronic Control Modules for more information.
  • Memory Heated Seat Module (MHSM) - If the vehicle is equipped with the Memory System, refer to Memory Seat Module in Electronic Control Modules for more information.
Refer to Power Seats Premium I/III in the Contents of Wiring Diagrams for complete circuit diagrams. Following are general descriptions of the major components in the heated seat system.

The heated seat system will only operate when the ignition switch is in the ON position, and the surface temperature at the front seat heating element sensors is below the designed temperature set points of the system. The heated seat system will not operate in ambient temperatures greater than about 41 °C (105 °F) . The front seat heating elements and sensors are hard wired to the Heated Seat Module (HSM) or the Memory Heated Seat Module (MHSM).

The heated seat switches are hard wired to the Body Control Module (BCM). The BCM monitors the heated seat switch inputs, then sends heated seat switch status messages to the HSM or MHSM over the Programmable Communications Interface (PCI) data bus. The HSM or MHSM contains the control logic for the heated seat system. The HSM or MHSM responds to the heated seat switch status messages, ignition switch status messages, and the front seat heating element sensor inputs by controlling the output to the front seat heating elements through integral solid-state relays.

When a seat heater is turned ON, the sensor located on the seat cushion electric heater element provides the HSM or MHSM with an input indicating the surface temperature of the seat cushion. If the surface temperature input is below the temperature set point for the selected Low or High heated seat switch position, the HSM or MHSM energizes the integral solid-state relay, which supplies battery current to the heating elements in the seat cushion and back. When the sensor input indicates the correct temperature set point has been achieved, the HSM or MHSM de-energizes the solid-state relay. The HSM or MHSM will continue to cycle the solid-state relay as needed to maintain the temperature set point.

The HSM or MHSM and the seat heater elements operate on non-switched battery current supplied through the power seat circuit breaker in the junction block. However, the HSM or MHSM will automatically turn OFF the heating elements if it detects an open or short in the sensor circuit, a short or open in the heating element circuit causing an excessive current draw, or when the ignition switch is turned to the OFF position.

See the owner's manual in the vehicle glove box for more information on the features, use and operation of the heated seat system.

I WILL POST THE REST

Jan 31, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Heated Seats do not work


i am a tech for chrysler jeep and dodge for the models such as your jeeps there is a recall for the heated seats we replace the elements.and also something could have spilled and got into the connections causing a short.check with your local dealer and see if the recall applys to your jeeps.

Dec 09, 2008 | 2001 Jeep Grand Cherokee

1 Answer

8 way power seat swap for power heated seat


i put new cars to gether an if it doesnt hav the acessories it wont have the harness u need,,maybe sumtymes they do but if ucan run aseperate switch itll work use the right amp rated wire or ull have more heat (fire)?thats about 12feet of wire they can save they will save if possible(wire harness) too bad i cant fix my own car thou,,,lol..

Nov 10, 2008 | 1998 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...