Question about 1994 Mitsubishi Montero

4 Answers

HELP!!!!need timing marks for pajero 94 2.8 auto *** import

Have to remove diesel pump,looking for timing marks on crankshaft,camshaft and spill-timing marks on diesel pump to remove timing chain in order to remove pump.thank you in advance................

Posted by on

  • 1 more comment 
  • splinter360 Feb 23, 2009

    HELP!!!!need timing marks for pajero 94 2.8 auto *** import" problem, and notify you when a new solution is offered.

  • MobileAutoS Mar 20, 2009

    Pajaro 96 2.8D injection pump timing diagram needed if possible

  • Anonymous Mar 14, 2014

    reassembling engine

×

Ad

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

There is a little mark on the crankshaft which you line up with the 'o' mark on the casing ..
remove the cam cover and look at the cam you should see a nob on the cam about 3 th lob and that should be facing just left of the engine ..
if you have a turbo there is two notchs on the injection pump pully ..if turbo there is a 't' mark on the rear of the cover the notch on the pully should mark up with the 't'..
the timing is set..

Posted on Mar 09, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Just had fuel pump front seal replaced, fitted pump back to engine,fitted acording to timing marks, set to the, T,mark for turbo;and notch on helical gear ;will start instantily, but will not idle properly ontil engine warm up, new heater plugs fitted, not smoking 1994 mit pajero 2800, sean,

Posted on Mar 13, 2011

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 243 Answers

Send me your email and I shall give you the pdf version of the procedures.
Cheers
technopro@windowslive.com

Posted on Feb 08, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

MY 2.8 MITSUBISHI CHALLENGER HAS A RATTLE THAT SOUNDS LIKE A BIG END BUT IS NOT , IT ONLY DOES IT AT ABOUT 13000 REVS IF U REV UP OR DOWN IT STOPS IT AND IT WILL PUFF OUT SOME SMOKE ONLY AT THAT TIME , ??????

Posted on Feb 07, 2010

  • BlackOnyx
    BlackOnyx Jul 06, 2013

    13,000 revs !!! It's probably engine parts leaving the engine!

  • BlackOnyx
    BlackOnyx Jul 06, 2013

    Could it be the cam chain being worn or loose, at 1300 revs, it might set up an harmonic wave or flick

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I put a water pump on 2.4 grand am


There are a lot of steps, and you need to take your time. You will need access to a lift or jack stand, and make sure you keep the work area clean and organised, taking photos of the timing system will make your life easier when it comes to re-timing the engine.

Water Pump Replacement (2.4L)
Removal Procedure
  1. Drain the coolant. Recover the coolant. Refer to Cooling System Draining and Filling.
  2. Remove the exhaust manifold. Refer to Exhaust Manifold Replacement in Engine Exhaust.
  3. Remove the coolant intake pipe. Refer to Engine Coolant Inlet Pipe Replacement in Engine Cooling.
  4. Lower the vehicle.
  5. Disconnect the heater hose quick connect from the heater outlet pipe.
  6. Remove the timing chain and tensioner. Refer to Camshaft Timing Chain, Sprocket, and Tensioner Replacement in Engine Mechanical - 2.4L. (see below procedure)
  7. Remove the water pump cover-to-cylinder block bolts.
  8. Remove water pump pipe to cylinder block bolt.
  9. Remove the 3?water pump-to-timing chain housing nuts.
  10. Remove the water pump and cover assembly.
  11. Remove the water pump cover-to-coolant pump assembly bolts.
  12. Clean all sealing surfaces.
Installation Procedure
    Important: Before you install the coolant pump, read the entire procedure. Follow the tightening sequences in order to avoid part damage and to provide proper sealing.

  1. Install the pump cover bolts. Hand tighten the bolts.
  2. Install water pump cover assembly.
  3. Install the cover-to-block bolts. Hand tighten the bolts.
  4. Install the coolant pump-to-timing chain housing nuts. Hand tighten the nuts.
  5. Notice: Refer to Fastener Notice in Cautions and Notices.
  6. Torque in sequence as follows:
    1. Tighten the water pump-to-timing chain housing nuts.
      Tighten
      Tighten water pump to timing chain housing nuts to 26?Y (19?lb?ft).
    2. Tighten the pump cover-to-pump assembly bolts.
      Tighten
      Tighten the water pump cove to water pump bolts to 14?Y (124?lb?in).
    3. Tighten the coolant pump cover-to-engine block bolts. Tighten the bottom bolt first.
      Tighten
      Tighten water pump to engine block bolts to 26?Y (19?lb?ft).
  7. Install heater hose to pipe on water pump.
  8. Install the exhaust manifold and install new gaskets. Refer to Exhaust Manifold Replacement in Engine Exhaust.
  9. Install oil level indicator tube and indicator. Refer to Oil Level Indicator Tube Replacement in Engine Mechanical-2.4L.
  10. Connect the brake vacuum pipe to the cam housing.
  11. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  12. Install catalytic converter to to manifold. Refer to Catalytic Converter Replacement in Engine Exhaust.
  13. Install the coolant inlet pipe. Refer to Engine Coolant Inlet Pipe Replacement.
  14. Install the timing chain and tensioner. Refer to Camshaft Timing Chain, Sprocket, and Tensioner Replacement in Engine Mechanical - 2.4L.
  15. Lower the vehicle.
  16. Connect the oxygen sensor connector.
  17. Fill cooling system. Refer to Cooling System Draining and Filling in Engine Cooling.
  18. Inspect the system for leaks.
Camshaft Timing Chain, Sprocket, and Tensioner Replacement
Removal Procedure
    Caution: Refer to Battery Disconnect Caution in Cautions and Notices.
    Notice: The timing chain on the LD9 (VIN T) Twin Cam Engine is not to be replaced with the timing chain from any other model year. The timing sprockets are different on the Twin Cam engine and the shape of the links matches the sprockets. Engine damage may result if the wrong timing chain is used. The timing chain and the crankshaft sprocket must be marked so that they are reinstalled in the same side facing out at the time of reassembly.
  1. Disconnect the negative battery cable.
  2. Remove the engine front cover. Refer to Engine Front Cover Replacement.
  3. Rotate the crankshaft clockwise (as viewed from the front of the engine, normal rotation) until the camshaft sprocket timing dowel pin holes align with the holes in the timing chain housing.
  4. Set the crankshaft sprocket keyway pointing upwards. Align with the centerline of the cylinder bores. This is the timed position.
  5. Remove the timing chain guides.
  6. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  7. Ensure that all of the slack in the timing chain is above the tensioner assembly.
  8. Remove the timing chain tensioner bolts and the tensioner.
  9. Remove the tensioner shoe. Use a small locking ring plier in order to engage the hole in the locking tab and remove the shoe from the stud.
  10. Notice: Do not attempt to pry the sprocket off the camshaft or damage to the sprocket or chain housing could occur.
    Important: Mark the timing chain and the crankshaft sprocket prior to removal. If the chain or the crankshaft sprocket is installed with the wear pattern in the opposite direction, noise and increased wear may occur.
  11. Mark the crankshaft sprocket and the timing chain outer surface.
  12. Remove the timing chain.
  13. Lower the vehicle.
  14. Holding the intake camshaft sprocket with J 39579, remove the sprocket bolt and washer.
  15. Remove the washer from the bolt and rethread the bolt back into the camshaft.
  16. Using a 3-jaw puller and the relief holes in the sprocket, remove the intake camshaft sprocket.
  17. Repeat this procedure for the exhaust camshaft sprocket.
  18. Clean the old sealant from the bolt with a wire brush.
  19. Clean the threaded hole in the camshaft with a round nylon bristle brush.
  20. Inspect the parts for wear. Replace the parts as necessary.Some scoring of the timing chain shoe and the guides is normal.
  21. Replace the timing chain shoe or guides if the scoring exceeds 1.12?mm (45?in).
Installation Procedure


  1. Use Adhesive/Sealant Compound GM?P/N?12345493 or equivalent on the camshaft sprocket bolt. Install the intake and exhaust camshaft sprockets onto the camshafts with the marked surface showing.Notice: Refer to Fastener Notice in Cautions and Notices.
  2. Install the retaining bolts and washers to the intake and exhaust camshaft sprockets.
  3. Tighten
    Tighten the bolts to 70?Y (52?lb?ft) while holding the sprockets with the J 39579.
  4. Install the J 36800 through the holes in the camshaft sprockets into the holes in the timing chain housing. This will position the camshaft for correct timing.
  5. If the camshafts are out of position (you must rotate the camshaft more than 1/8?turn in order to install the alignment dowel pins), use the following procedure:
    1. Rotate the crankshaft 90?degrees clockwise off of the TDC in order to give the valves adequate clearance to open.
    2. Once the camshafts are in position and the dowels installed, rotate the crankshaft counter clockwise back to the top dead center.

  6. Notice: Do not rotate the crankshaft clockwise to TDC. Valve or piston damage could occur.
    Important: The side of the timing chain that was marked during removal must be showing when the chain is installed.
  7. Install the timing chain over the exhaust camshaft sprocket, around the coolant pump, and around the crankshaft sprocket.
    1. Remove the alignment dowel pin from the intake camshaft.
    2. Using the J 39579, rotate the intake camshaft sprocket counterclockwise enough in order to slide the timing chain over the intake camshaft sprocket.
    3. Release the J 39579. The length of the chain between the 2?camshaft sprockets will tighten.
    4. If properly timed the intake camshaft alignment dowel pin should slide in easily. If the dowel pin does not fully index, the camshafts are not timed correctly and the procedure must be repeated.
  8. Leave the alignment dowel pins installed.
  9. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  10. The timing marks on the crankshaft and on the cylinder block should be aligned when the slack is removed from the chain linking the intake camshaft sprocket and the crankshaft sprocket. If the marks are not aligned, move the chain one tooth forward or rearward, remove the slack and re-examine the marks.

  11. Important: Use the following steps in order to reset the timing chain tensioner assembly to the zero position.
  12. Reset the timing chain tensioner assembly.
    1. Insert the tensioner plunger assembly into the tensioner housing.
    2. With the tensioner plunger fully extended, turn the complete assembly upside down on a bench or other flat surface.
    3. With the plunger face against the workbench, press firmly on the bottom of the tensioner housing.
    4. Compress the plunger until the plunger is seated flush in the tensioner.

  13. Check the plunger to make sure the plunger is out of the cylinder at the correct dimension. The correct dimension for the plunger to extend out of the cylinder is 1.7?mm (0.07?in) maximum.

  14. Loosely install the tensioner assembly and bolts to the timing chain housing.
  15. Install the timing chain tensioner shoe on the stud.
  16. Apply hand pressure to the timing chain tensioner shoe until the locking tab seats in the groove in the stud.
  17. Tighten the timing chain tensioner bolts. Do Not overtighten.
    Tighten
    Tighten the bolts to 10?Y (89?lb?in).


  18. Important: If the timing chain tensioner is not released from the installation position, engine damage will occur when the engine is started.
  19. Release the timing chain tensioner plunger.
    1. Using a flat blade screwdriver, cotter pin remover, or similar tool, press firmly against the face of the timing chain tensioner plunger.
    2. Important: If the timing chain tensioner cannot be depressed, the plunger is not properly reset and the procedure for resetting the timing chain tensioner should be repeated.
    3. Depress the timing chain tensioner plunger until the plunger is bottomed out in the bore of the timing chain tensioner.
    4. Release the tensioner plunger. the plunger should press firmly against the back of the timing chain tensioner shoe.
  20. Remove J 36800 from the camshaft sprockets.
  21. Rotate the crankshaft clockwise 2?full rotations. Align the crankshaft keyway with the mark on the cylinder block, and reinstall the alignment dowel pins. The pins should slide in easily if the engine is timed correctly.

  22. Install the timing chain guides.
  23. Install the engine front cover. Refer to Engine Front Cover Replacement.
  24. Connect the negative battery cable.
    Tighten
    Tighten the bolt to 16?Y (12?lb?ft).

Jul 02, 2016 | Cars & Trucks

2 Answers

03 Suzuki aerio need a step by step how to: replace the timing chain! Please help


WOW you work on engines not knowing what is there?
the engines are: 7 engines.!!!
1.3 L I4; 1.5 L I4; 1.6 L I4; 1.8 L I4; 2.0 L I4; 2.3 L I4; 1.4 L Diesel I4 ill guess, ( (die roll)
2.3 L below.

all answers, USA cars, this a USA forum. so.....
ever heard of the FSM the oem factory service manual?

is the chain making noises? if yes, the guide is bad, most chains fail due to that (as a true cause)
the FSM is here , just $4 to look , so ????
https://suzukipitstopplus.com/Products/1178-2003-aerio-service-manual.aspx

the clone is Alldata.com DIY, log in and read like we do.
google alldtata.com , bingo....

now the 2.3L (just the first half, ill let you pay $4 like we do)
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove engine assembly from vehicle.
  3. Remove oil pan.
  4. Remove cylinder head cover.
  5. Remove timing chain cover as follows:
    • Remove crankshaft pulley bolt. To lock crankshaft pulley, use special tool 09917-68221 (camshaft pulley holder).
    • Remove crankshaft pulley. To remove crankshaft pulley, use special tools 09944-36011 and 09926-58010 (steering wheel remover and bearing puller attachment).
    • Remove A/C compressor bracket.
    • Remove alternator belt idler pulley, water pump pulley and alternator belt tensioner.
    • Remove timing chain cover bolts and nut.
    • For reinstallation of timing chain, turn crankshaft so that timing marks on cylinder head and lower crankcase match with those on sprockets as shown in figure.
    • Remove second timing chain as follows:
      • Turn crankshaft to meet following conditions.
        • Key (I) on crankshaft is positioned as shown.
        • Arrow mark on idler sprocket (II) points upward.
        • Marks on sprockets (III) match with marks on cylinder head. Note that this step must be followed for reinstallation of timing chain.
      • Remove timing chain tensioner adjuster No.2 and gasket. To remove them, slacken second timing chain by turning intake camshaft counterclockwise a little while pushing back pad.
      • Remove intake and exhaust camshaft timing sprocket bolts. To remove them, fit a spanner to hexagonal part at the center of camshaft to hold it stationary.
      • Remove camshaft timing sprockets and second timing chain.
      • warning
      • After second timing chain is removed, never turn intake camshaft, exhaust camshaft and crankshaft independently more than such an extent as shown. If turned, interference may occur between piston and valves and valves themselves, and parts related to piston and valves may be damaged.
      • Remove timing chain guide No.1.
      • Remove timing chain tensioner adjuster No.1.
      • Remove timing chain tensioner.
      • Remove idler sprocket and first timing chain.
      • Remove crankshaft timing sprocket.
      • end.
    im not doing INSTALL, sorry.


25540491-yqaloxbadhjyikzm2dpnlv4n-2-0.jpg got that? also there are a hole section on details of gasket seals and such, nothing trivial that.

Mar 09, 2015 | 2003 Suzuki Aerio

3 Answers

How I change a timing chain to a suzuki aereo 2003?


wow no engine stated of the many.
1.3 L I4; 1.5 L I4; 1.6 L I4; 1.8 L I4; 2.0 L I4; 2.3 L I4; 1.4 L Diesel I4 amazing huh, no engine or COUNTRY stated.
my answer will be USA< as this is a USA forum
and like all cars in USA the engine list it smaller (EPA rule and Bs)
ever seen and FSM book, factory service manual
for any car made, ?
2nd best is always.... here. log in an read?
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

real FSMs. here (official suz. site)
or at suzukipitstop (google it)

no my GUESS,(useless if outside USA totally, mostly)

2.0 or 2.3L: working on engines, not knowing what is there???
here is the teaser answer, no photos , no warnings, etc.

quoted in part, and remove chain only.
exploded view of first timing chain and related components-2.0L and 2.3L engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove engine assembly from vehicle.
  3. Remove oil pan.
  4. Remove cylinder head cover.
  5. Remove timing chain cover as follows:
    • Remove crankshaft pulley bolt. To lock crankshaft pulley, use special tool 09917-68221 (camshaft pulley holder).
Be sure to use the following bolts instead of pins for fixing special tool to crankshaft pulley. Bolt size: M8, P1.25 L = 25 mm (0.98 in.) Strength: 7T

  • Remove crankshaft pulley. To remove crankshaft pulley, use special tools 09944-36011 and 09926-58010 (steering wheel remover and bearing puller attachment).
  • Remove A/C compressor bracket.
  • Remove alternator belt idler pulley, water pump pulley and alternator belt tensioner.
  • Remove timing chain cover bolts and nut.

  1. For reinstallation of timing chain, turn crankshaft so that timing marks on cylinder head and lower crankcase match with those on sprockets as shown in figure.
  2. Remove second timing chain as follows:
    • Turn crankshaft to meet following conditions.
      • Key (I) on crankshaft is positioned as shown.
      • Arrow mark on idler sprocket (II) points upward.
      • Marks on sprockets (III) match with marks on cylinder head. Note that this step must be followed for reinstallation of timing chain.
    • Remove timing chain tensioner adjuster No.2 and gasket. To remove them, slacken second timing chain by turning intake camshaft counterclockwise a little while pushing back pad.
    • Remove intake and exhaust camshaft timing sprocket bolts. To remove them, fit a spanner to hexagonal part at the center of camshaft to hold it stationary.
    • Remove camshaft timing sprockets and second timing chain.
After second timing chain is removed, never turn intake camshaft, exhaust camshaft and crankshaft independently more than such an extent as shown. If turned, interference may occur between piston and valves and valves themselves, and parts related to piston and valves may be damaged.

  1. Remove timing chain guide No.1.
  2. Remove timing chain tensioner adjuster No.1.
  3. Remove timing chain tensioner.
  4. Remove idler sprocket and first timing chain.
  5. Remove crankshaft timing sprocket.
end remove section.



why not log in and read all words, steps and warnings..>>???

http://www.scantool.net/software/alldata-diy-1-month-subscription.html

end teaser.

Dec 10, 2014 | 2003 Suzuki Aerio

1 Answer

How do i reset the timing on 2001 2.7l concorde if the chain was replaced and the timing is off


Did you take pictures while removing the originals? It's always a good habit. Below are the instructions you need to follow. Your own pics are very helpful when doing a big job like this.
  1. Disconnect negative battery (1) cable.
  2. Drain cooling system.
  3. Remove upper intake manifold.
  4. Remove cylinder head covers, crankshaft vibration damper, and timing chain cover.
CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.
117014297

  1. Align crankshaft sprocket timing mark to mark on oil pump housing (2). The mark on oil pump housing is 600 ATDC of #1 cylinder.
CAUTION: When the timing chain is removed and the cylinder heads are still installed, DO NOT rotate the camshafts or crankshaft without first locating the proper crankshaft position. Failure to do so will result in valve and/or piston damage.
117016938

  1. Remove primary timing chain tensioner retainer cap (2) and tensioner (1) from right cylinder head.
117016939

  1. Disconnect and remove camshaft position sensor (4) from left cylinder head.
  2. Remove timing chain guide access plugs (3) from cylinder heads.
NOTE: When camshaft sprocket bolts are removed, the camshafts will rotate in a clockwise direction.
  1. Starting with the right camshaft sprocket, remove the sprocket attaching bolts. Remove camshaft damper (1) (if equipped) and sprocket.
  2. Remove left side camshaft sprocket attaching bolts and remove sprocket.
  3. Remove lower chain guide (7) and tensioner arm (8).
  4. Remove the primary timing chain (5).
  5. Remove crankshaft sprocket (6).
INSTALLATION
117016940

  1. Inspect all sprockets (4,9,11) and chain guides (2,5,10). Replace if worn.
  2. For crankshaft sprocket installation procedures Refer to CRANKSHAFT SPROCKET.
  3. If removed, install right and left side short chain guides (11). Tighten attaching bolts to 28 Nm (250 inch lbs.) .
  4. Align crankshaft sprocket timing mark to the mark on oil pump housing (3).
NOTE: Lubricate timing chain and guides with engine oil before installation.
  1. Place left side primary chain sprocket onto the chain so that the timing mark is located in-between the two (plated) timing links (1).
117016941

  1. Lower the primary chain with left side sprocket through the left cylinder head opening.
NOTE: The camshaft sprockets can be allowed to float on the camshaft hub during installation.
  1. Loosely position left side camshaft sprocket over camshaft hub.
  2. Align timing (plated) link to the crankshaft sprocket timing mark (3).
  3. Position primary chain onto water pump drive sprocket (10).
  4. Align right camshaft sprocket timing mark to the timing (plated) link on the timing chain (8) and loosely position over camshaft hub.
  5. Verify that all chain timing (plated) links are properly aligned to the timing marks on all sprockets.
  6. Install left side lower chain guide (2) and tensioner arm (5). Tighten attaching bolts to 28 Nm (250 inch lbs.) .
NOTE: Inspect O-ring on chain guide access plugs before installing. Replace O-ring as necessary.
  1. Install chain guide access plugs to cylinder heads. Tighten plugs to 20 Nm (15 ft. lbs.) .
NOTE: To reset the primary timing chain tensioner, engine oil will first need to be purged from the tensioner.
117016942

  1. Purge oil from timing chain tensioner using the following procedure:
    1. Place the check ball (2) end of tensioner into the shallow end of Special Tool 8186 (3).
    2. Using hand pressure, slowly depress tensioner until oil is purged from tensioner.
117016943

  1. Reset timing chain tensioner using the following procedure:
    1. Position cylinder plunger (4) into the deeper end of Special Tool 8186 (3).
    2. Apply a downward force until tensioner is reset.
NOTE: If oil was not first purged from the tensioner, use slight finger pressure to assist the center arm pin of Special Tool 8186 to unseat the tensioner's check ball.

CAUTION: Ensure the tensioner is properly reset. The tensioner body (4) must bottom against the top edge of Special Tool 8186 (3). Failure to properly perform the resetting procedure may cause tensioner jamming.

NOTE: Inspect the tensioner O-ring (2) for nicks or cuts and make sure the snap ring (1) is correctly installed, replace as necessary.
117016944

  1. Install the reset chain tensioner (1) into the right cylinder head.
  2. Position tensioner retaining plate (2) and tighten bolts (1) to 12 Nm (105 inch lbs.) .
117016945

  1. Starting at the right cylinder bank, first position the camshaft damper (1) (if equipped) on camshaft hub, then insert a 3/8 square drive extension with a breaker bar into intake camshaft drive hub. Rotate camshaft until the camshaft hub aligns to the camshaft sprocket and damper attaching holes. Install the sprocket attaching bolts and tighten to 28 Nm (250 inch lbs.) .
  2. Turn the left side camshaft by inserting a 3/8 square drive extension with a breaker bar into intake camshaft drive hub and rotate camshaft until the sprocket attaching bolts can be installed. Tighten sprocket bolts to 28 Nm (250 inch lbs.).
  3. Rotate engine slightly clockwise to remove timing chain slack, if necessary.
117016946

  1. Activate the timing chain tensioner by using a flat bladed pry tool to gently pry tensioner arm towards the tensioner slightly. Then release the tensioner arm. Verify the tensioner is activated (extends).
117016947

  1. Install camshaft position sensor (2) and connect electrical connector.
  2. Install the timing chain cover, crankshaft vibration damper, and cylinder head covers.
  3. Install upper intake manifold.
NOTE: After installation of a reset tensioner, engine noise will occur after initial start-up. This noise will normally disappear within 5-10 seconds.
  1. Fill cooling system.

Mar 27, 2013 | 2001 Chrysler Concorde

2 Answers

Need timing gear marks for 2004 Kia Sadona 3.5L engine



Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Record the radio anti theft code data.
  3. Remove or disconnect the following:

    Negative battery cable Engine cover Accessory drive belts Idler pulley Crankshaft pulley Power steering pump pulley Belt tensioner pulley Upper and lower timing belt covers
  4. Support the engine with a floor jack and remove the engine mount.
  5. Rotate the engine to align the camshaft sprocket timing marks with the cylinder head cover timing marks.

    0996b43f8022cb71.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt routing and timing marks-3.5L Engine

  6. Remove or disconnect the following:

    Auto tensioner Timing belt

    0996b43f8022cb72.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt and related components-3.5L Engine


To install:
  1. Ensure that the engine is set to Top Dead Center (TDC).
  2. Prepare the auto tensioner for installation by compressing it in a vise and installing a retaining pin.
  3. Install the timing belt in the following order:
    1. Crankshaft sprocket
    2. Idler pulley
    3. Left bank exhaust camshaft sprocket
    4. Left bank intake camshaft sprocket
    5. Water pump pulley
    6. Right bank intake camshaft sprocket
    7. Right bank exhaust camshaft sprocket
    8. Tensioner pulley

  4. Install the auto tensioner. Do not remove the retaining pin at this time.
  5. Check that the crankshaft and camshaft timing marks are aligned correctly.
  6. Rotate the crankshaft 1 / 4 turn Counterclockwise .
  7. Rotate the crankshaft 1 / 4 turn Clockwise to return the engine to TDC.
  8. Loosen the tensioner pulley center bolt.
  9. Apply 44 inch lbs. (5 Nm) torque to the tensioner pulley as shown and tighten the center bolt to 32-41 ft. lbs. (43-55 Nm).

    0996b43f8022cb73.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Adjusting the tensioner pulley-3.5L Engine

  10. Remove the auto tensioner retaining pin.
  11. Rotate the crankshaft 2 revolutions Clockwise , then wait 5 minutes for the auto tensioner to adjust.
  12. Measure the auto tensioner rod as shown. If the measurement is not 3.8-4.5 mm, then repeat the belt tensioning procedure.

    0996b43f8022cb74.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Measuring the auto tensioner rod-3.5L Engine

  13. When the auto tensioner measurement is correct, install or connect the following:

    Engine mount Upper and lower timing belt covers Belt tensioner pulley Power steering pump pulley Crankshaft pulley Idler pulley Accessory drive belts Engine cover Negative battery cable
  14. Reprogram the radio anti theft codes.

    Kia_Sedona_2002-2006
    Timing Chain, Sprockets, Front Cover & Seal

    Print


    Removal & Installation

    3.8L Engine

    1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
    2. Record the radio anti theft code data.
    3. Remove the engine from the vehicle.
    4. Remove the drive belt. Remove the power steering pump. Remove the air conditioning compressor.
    5. Remove the alternator. Remove the drive belt idler. Remove the drive belt tensioner. Remove the water pump pulley. Remove the intake manifold.
    6. Remove the connector bracket from the left cylinder head cover. Disconnect the right ignition coil connector, condenser connector and remove the bracket.
    7. Remove the left cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    8. Remove the right cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    9. Set the No. 1 cylinder to TDC on the compression stroke. Turn the crankshaft pulley and align its groove with the timing mark T of the lower timing chain cover.
    10. Check that the mark of the camshaft timing sprockets are in straight line positioning on the cylinder head surface. If not rotate the crankshaft 360 degrees. Do not rotate the engine counterclockwise.
    11. Remove the oil pan. Remove the crankshaft damper pulley. Remove the timing chain cover.
      NOTE Be careful not to damage the contact surfaces of the cylinder block, cylinder head and timing chain cover. Before removing the timing chain, mark the right and left timing chains with an identification mark based on the location of the sprocket because the identification mark on the chain for TDC can be erased.
    12. After compressing the timing chain tensioner, install a set pin. Remove the right cam to cam guide. Remove the right timing chain auto tensioner and timing chain tensioner arm.
    13. Remove the oil pump chain cover. Remove the oil pump chain tensioner assembly. Remove the oil pump chain guide. Remove the right timing chain.
    14. Remove the right timing chain guide. Remove the oil pump chain sprocket and oil pump chain. Remove the crankshaft sprocket, oil pump and camshaft drive gear.
    15. Remove the left cam to cam guide. Remove the left timing chain auto tensioner and timing chain tensioner arm. Remove the left timing chain.
    16. Remove the left timing chain guide. Remove the crankshaft sprocket and left camshaft drive. Remove the tensioner adapter assembly.

      0996b43f8020193b.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing chain and related components-3.8L Engine


    To install:
    1. Check the camshaft and crankshaft sprockets for wear and damage, replace as required.
    2. Inspect the tensioner arm and chain guide for wear and damage, replace as required.
    3. Check that the tensioner pin moves smoothly when the ratchet pawl is released with a thin rod.
    4. The key of the crankshaft should be aligned with the timing mark of the timing chain cover. This indicates that the piston is at TDC on the compression stroke.
    5. Install the tensioner adapter assembly. Install the crankshaft sprocket and left camshaft drive.
    6. Install the left timing chain guide and torque the retaining bolts 14-18 ft. lbs.
    7. Install the left timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, timing chain guide, exhaust camshaft sprocket, intake camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201924.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Left timing chain markings and installation: (D) exhaust camshaft sprocket (C) intake camshaft sprocket-3.8L Engine

    8. Install the left timing chain tensioner arm and torque the retaining bolts 14-16 ft. lbs.
    9. Install the left timing chain tensioner and torque the retaining bolts 7-9 ft. lbs.
    10. Install the left cam to cam guide and torque the retaining bolts 7-9 ft. lbs.
    11. Install the crankshaft sprocket, oil pump and right camshaft drive.
    12. Install the oil pump chain and oil pump sprocket. Torque the retaining bolt to 14-16 ft. lbs.
    13. Install the right timing chain guide. Torque the retaining bolts to 14-18 ft. lbs.
    14. Install the right timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, intake camshaft sprocket, exhaust camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201925.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Right timing chain markings and installation: (C) exhaust camshaft sprocket (B) intake camshaft sprocket-3.8L Engine

    15. Install the right timing chain tensioner arm. Torque the retaining bolts to 14-17 ft. lbs.
    16. Install the right timing chain auto tensioner. Torque the retaining bolts to 7-9 ft. lbs.
    17. Install the right cam to cam guide and torque the retaining bolts to 7-9 ft. lbs.
    18. Install the oil pump chain guide. Torque the retaining bolts to 7-9 ft. lbs.
    19. Install the oil pump tensioner assembly. Torque the retaining bolts to 7-9 ft. lbs.
    20. Pull out the pins on both the left and right hydraulic tensioners. Install the oil pump chain cover.
    21. Rotate the crankshaft two revolutions in the clockwise direction. Confirm the timing mark. Be sure to rotate the crankshaft in the clockwise direction.
    22. Apply sealant on the chain cover and on the cylinder head, cylinder block, and lower oil pan. Be sure these parts are free of engine oil and dirt.
      NOTE Before assembling the timing chain cover, the liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201926.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Sealant application (1 inch bead width)-3.8L Engine

    23. Apply sealant on the chain cover.
      NOTE The liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201927.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover sealant application-3.8L Engine

    24. Install a new gasket to the timing case cover.
      NOTE It is important that the dowel pins on the cylinder block and holes on the timing chain cover should be used as a reference in order to assemble the timing chain cover in the correct position.


      0996b43f80201928.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover gasket installation (A) gaskets-3.8L Engine

    25. Install the timing chain cover. Torque the retaining bolts in the proper sequence and to specification. The engine should not be started for at least thirty minutes after timing chain cover assembly.

      0996b43f80201929.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover bolt torque sequence and specification-3.8L Engine

    26. Install the timing case cover oil seal.
    27. Continue the installation in the reverse order of the removal procedure.

May 19, 2012 | 2004 Kia Sedona

1 Answer

How do u set timing on it? 1.8 engine


Installation
Install crankshaft sprocket on crankshaft.
Make sure mating marks on crankshaft sprocket face front of engine.

Position crankshaft so that No. 1 piston is at TDC and crankshaft key is at 12 o'clock.

Install slack side timing chain guide and timing chain tension guide.

Install timing chain on crankshaft sprocket.
Set timing chain by aligning its mating mark with that on the crankshaft sprocket.
Make sure sprocket's mating mark faces engine front.

Install camshaft sprockets.
Set timing chain by aligning mating marks with those of camshaft sprockets.

Install camshaft sprocket bolts to correct torque.
Apply new engine oil to bolt threads and seat surface.

Install chain tensioner.
Before installing chain tensioner, insert a suitable pin into pin hole of chain tensioner.
After installing chain tensioner, remove the pin.
Install timing chain guide.

Install O-rings to cylinder block.

Before installing front cover, remove all traces of RTV silicone sealant from mating surface using a scraper.
Also remove traces of RTV silicone sealant from mating surface of cylinder block.

Apply a continuous bead of Genuine RTV Silicone Sealant or equivalent to mating surface of front cover. Refer to RECOMMENDED CHEMICAL PRODUCTS AND SEALANTS .
Check alignment of mating marks on chain and crankshaft sprocket.
Align oil drive spacer with oil pump.
Place timing chain to the side of chain guide. This prevents the chain from making contact with water seal area of front cover.

Install front cover.

Make sure two O-rings are present.

Be careful not to damage oil seal when installing front cover.
Install cylinder head bolts at engine front side as shown in Fig. 55.
Tightening procedure:
Tighten bolts (1 - 4): 6.3-8.3 N.m (0.64-0.85 kg.m, 55.8-73.5 in.lb).

Install oil pump drive spacer.
Install water pump and water pump pulley. Refer to REMOVAL AND INSTALLATION .
Install idler pulley and bracket.

Install RH engine mounting bracket

Install RH engine mounting.
Install oil pan. Refer to INSTALLATION.
Install crankshaft pulley.
Remove ring gear stopper.
Install starter motor.
Install cylinder head front cover.
Apply RTV silicone sealant to cylinder head front cover.
Use Genuine RTV Silicone Sealant or equivalent. Refer to RECOMMENDED CHEMICAL PRODUCTS AND SEALANTS .

Install Camshaft Position Sensor (PHASE).

Before installing rocker cover, apply a bead of Genuine RTV Silicone Sealant or equivalent, to mating surface of cylinder head as shown in .

Install rocker cover gasket into rocker cover.
Install rocker cover and tighten in numerical order as shown in
Install spark plugs.
Install ignition coils.
Install front exhaust tube.
Install front/right-side splash undercover.
Install front RH wheel.
Install drive belts.
Adjusting drive belt deflection..

Nov 29, 2010 | 2002 Nissan Sentra

2 Answers

2001 chev cavalier timming chain diagram


Timing Chain and Gears REMOVAL & INSTALLATION 2.2L Engine Fig. 1: The timing marks on the sprockets should be in alignment. If not, turn the crankshaft until the marks are aligned 91113p63.jpg
Fig. 2: The timing chain tensioner is retained by a Torx head bolt (1) and a regular hex head bolt (2) 91113p58.jpg
Fig. 3: Unfasten the camshaft sprocket bolt 91113p59.jpg
Fig. 4: Remove the camshaft sprocket and the timing chain at the same time . . . 91113p60.jpg
Fig. 5: . . . then remove the tensioner assembly 91113p61.jpg
Fig. 6: Compress the tensioner spring and insert a cotter pin or nail in the hole provided to hold the tensioner in position 91113p62.jpg
  1. Disconnect the negative battery cable.
  2. Remove the front cover as previously detailed.
  3. Place the No. 1 piston at TDC of the compression stroke so that the marks on the camshaft and crankshaft sprockets are in alignment (see illustration).
  4. Loosen the timing chain tensioner nut as far as possible without actually removing it.
  5. Remove the camshaft sprocket bolts and remove the sprocket and chain together. If the sprocket does not slide from the camshaft easily, a light blow with a soft mallet at the lower edge of the sprocket will dislodge it.
  6. Using a suitable gear puller, remove the crankshaft sprocket. To install:
  7. Press the crankshaft sprocket back onto the crankshaft.
  8. Install the timing chain over the camshaft sprocket and then around the crankshaft sprocket. Make sure that the marks on the two sprockets are in alignment (see illustration). Lubricate the thrust surface with Molykote® or its equivalent.
  9. Align the dowel in the camshaft with the dowel hole in the sprocket and then install the sprocket onto the camshaft. Use the mounting bolts to draw the sprocket onto the camshaft and then tighten to 66-68 ft. lbs. (91-95 Nm).
  10. Lubricate the timing chain with clean engine oil. Tighten the chain tensioner.
  11. Installation of the remaining components is in the reverse order of removal. Fig. 7: Exploded view of the timing chain and sprockets - 2.2L OHV engine 87953107.gif

Nov 11, 2010 | Chevrolet Cavalier Cars & Trucks

1 Answer

How to set the timing on 1998 GMC Sierra 5.7


5.0L and 5.7L Engines To Remove:
  1. Remove the crankshaft balancer.
  2. Drain the cooling system.
  3. Remove the water pump.
  4. Drain the engine oil.
  5. Remove all engine oil pan fasteners except two nuts at rear of engine.
  6. Separate the engine oil pan from the front cover.
  7. Disconnect the crankshaft position (CKP) sensor wire. gm-03-50-845.gif

  8. Remove engine front cover. gm-03-50-849.gif

  9. Pry the oil seal from the front cover.
  10. Inspect the front cover seal area and crankshaft balancer seal area for damage. gm-03-50-846.gif

  11. Rotate the crankshaft until the timing marks on the crankshaft and the camshaft sprockets are aligned.
  12. Remove the crankshaft position sensor reluctor ring. gm-03-50-847.gif

    NOTE: Free play on the slack side of the camshaft timing chain must measure less than 0.43 inch (11Mm) or timing chain and sprockets must be replaced.
  13. Remove the camshaft sprocket bolts.
  14. Remove the camshaft sprocket.
  15. Remove the camshaft timing chain. NOTE: Do not turn the crankshaft assembly after the timing chain has been removed in order to prevent damage to the piston assemblies or the valves.
    gm-03-50-848.gif

  16. Remove the crankshaft sprocket using J 5825-A.
  17. Remove the crankshaft balancer woodruff keys (if required).
To Install:
gm-03-50-850.gif

  1. Install the crankshaft balancer woodruff keys into the crankshaft.
  2. Align the crankshaft sprocket keyway with the crankshaft balancer woodruff key. WARNING
    Wear eye protection when installing crankshaft sprocket.
    gm-03-50-851.gif

  3. Use J 5590 to install crankshaft sprocket.
  4. Install the camshaft sprocket and camshaft timing chain. 9308kg61.gif

  5. Ensure that the crankshaft sprocket alignment mark is in the 12 o'clock position and the camshaft sprocket alignment mark is at the 6 o'clock position.
  6. Install the camshaft sprocket bolts and tighten the camshaft sprocket bolts;
    • Torque to: 18 ft. lbs. (25 Nm)
  7. Install the crankshaft position sensor reluctor ring until completely seated against crankshaft sprocket. NOTE: The composite type engine front cover and seal must not be reused. Always install a new engine cover with a new seal.
  8. Install new engine front cover and bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  9. Clean sealer from corners of oil pan gasket where it meets the engine front cover. gm-03-50-775.gif

  10. Apply a 0.196 in (5 mm) bead of adhesive, GM P/N 12346141 or equivalent, 1.0 in (25 mm) long to the engine front cover to engine block junction.
  11. Install oil pan bolts.
    • Torque bolts to: 106 in. lbs. (12 Nm)
  12. Tighten oil pan nuts.
    • Torque bolts to: 18 ft. lbs. (25 Nm)
  13. Connect the crankshaft position sensor wire.
  14. Install the water pump.
  15. Install the crankshaft balancer.
  16. Fill the engine to the proper level with oil.
  17. Fill the engine to the proper level with coolant.
  18. Test drive the vehicle to confirm the repairs.

Nov 05, 2010 | GMC K1500 Cars & Trucks

1 Answer

Replacing the timing belt on a 1998 Nissan Quest and need to know cam shaft and crank shaft positions.


go here for expert help on Villager & Quest

http://groups.yahoo.com/group/villagerquest/

e09cf57.gif

Item Part Number Description 1 — 40 Timing Chain/Belt Teeth 2 6256 Camshaft Sprocket , Front 3 — 43 Timing Chain/Belt Teeth 4 6306 Crankshaft Sprocket 5 6268 Timing Chain/Belt 6 6256 Camshaft Sprocket , Rear
Removal
  1. Drain the cooling system. Refer to Section 03-03 for the procedure.
  1. Disconnect the battery ground cable (14301) .
  1. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedure.
  1. If equipped, remove the three A/C compressor drive belt idler pulley bolts and the A/C compressor drive belt idler pulley.
  1. Remove the upper radiator hose bracket bolt.
  1. Loosen the two upper radiator hose clamps and remove the radiator hose bracket bolt. Remove the upper radiator hose (8260) and the upper radiator hose bracket from the vehicle.
  1. Remove the water bypass hose (8597) from between the thermostat housing and the water hose connection (8592) .
  1. Remove the main wiring harness from the upper engine front cover (6019) .
  1. Remove the eight upper engine front cover bolts and the upper engine front cover .
  1. Raise and support the vehicle.
  1. Remove the RH front wheel and tire assembly.
  1. Remove the four RH outer engine and transmission splash shield bolts and two screws and remove the RH outer engine and transmission splash shield (6775) .
  1. Use Strap Wrench 303-D055 (D85L-6000-A) or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts.
  1. Remove the water pump pulley from the water pump (8501) .
  1. Remove the crankshaft pulley (6312) . Refer to the procedure in this section.
  1. Remove the five lower engine front cover bolts and the lower engine front cover .
  2. Ensure that the timing marks between the crankshaft sprocket (6306) and the oil pump housing line up.
  3. NOTE: The directional arrow is necessary to ensure that the timing chain/belt (6268) can be reinstalled in the same direction.
  4. Loosen the timing chain/belt tensioner nut.
  5. Remove the timing chain/belt .

  6. Installation
    NOTE: Ensure that the timing marks on the camshaft sprockets (6256) and the seal plate are properly aligned. Ensure that the timing marks on the crankshaft sprocket and the oil pump housing are still aligned. NOTE: A new timing chain/belt has three white timing marks that indicate the correct timing positions of the camshafts (6250) and the crankshaft (6303) . These marks will help ensure that the engine (6007) is timed properly. When the engine is properly timed each white timing mark on the timing chain/belt will be aligned with the corresponding camshaft and crankshaft timing mark on the sprocket. Because the white timing marks are not evenly spaced you will need to refer to the following illustration for proper timing chain/belt placement. There should be 40 timing belt teeth between the timing marks of the front and rear camshaft sprockets and 43 teeth between the timing mark on the front camshaft sprocket and the timing mark on the crankshaft sprocket .

    NOTE: Verify that the camshaft timing marks are aligned with the timing marks on the seal plate, and that the crankshaft sprocket timing mark is aligned with the timing mark on the oil pump (6600) .

    Install the timing chain/belt starting at the crankshaft sprocket and moving around to the camshaft sprocket following a counterclockwise path. Do not allow any slack in the timing chain/belt between the timing sprockets. After all of the timing marks are matched up with the timing chain/belt installed, slip the timing chain/belt onto the timing chain/belt tensioner .





Sep 20, 2009 | 1998 Nissan Quest

2 Answers

I need the diagram for the balance chain timing


Except Premier
Procedures applying to removal and installation of the auxiliary shaft drive chains are located under Auxiliary (Intermediate or Silent) Shafts Removal and Installation, later in this section.
2.5L Premier Engine (See Figures 1 through 5)

Fig. 1: To remove the timing chain, remove the timing chain case cover
641e9f9.gif
Fig. 2: When removing and installing the timing chain the crankshaft and camshaft sprocket timing marks should be aligned as shown
17939a6.gif
Fig. 3: While holding the timing chain, camshaft sprocket and crankshaft sprocket aligned install them onto the engine
7b5b4f8.gif

Fig. 4: Lock and unlock the timing chain tensioner by switching the tensioner lever, as shown
d87be65.gif

Fig. 5: To verify correct installation, turn the crankshaft until the camshaft sprocket timing mark is approximately at the one o'clock position, then count the number of chain link pins between the points shown
0f6902b.gif

  1. Disconnect the negative battery cable.
  2. Remove the fan shroud and cooling fan, as described earlier in this section.
  3. Remove the accessory drive belts. For more information, refer to .
  4. Remove the water pump pulley and crankshaft vibration damper, as described earlier in this section.
  5. Remove the timing case cover, as described previously in this section.
It is a good practice to either remove or cover the radiator area when performing extensive repairs to the engine to prevent accidental damage to the radiator core.
  1. Rotate the crankshaft until the 0 timing mark on the crankshaft sprocket is closest to and on a center line with the timing mark on the camshaft sprocket.
  2. Remove the oil slinger from the crankshaft.
  3. Remove the camshaft retaining bolt and remove the sprockets and chain as an assembly.
  4. If the timing chain tensioner is to be replaced, the oil pan must also be removed.
To install:
  1. Turn the tensioner lever to the unlock (down) position and pull the tensioner block toward the tensioner lever to compress the spring. Hold the block and turn the tensioner lever to the lock (up) position.
  2. Install the crankshaft sprocket, camshaft sprocket and timing chain together. Make sure the timing marks are aligned as indicated in Step 6 and in the accompanying illustration.
  3. Install the camshaft sprocket retaining bolt and washer. Tighten the bolt to 80 ft. lbs. (108 Nm).
  4. To verify correct installation of the timing chain, rotate the crankshaft until the camshaft sprocket timing mark is approximately at the 1 o'clock position. Count the number of chain link pins between the camshaft timing mark and the crankshaft timing mark, there should be 20 pins (2 per link) between the marks.
  5. Make sure that the timing chain tensioner switches to the unlocked position. If the tensioner does not switch automatically unlock, switch it manually to the unlock position.
  6. Install the oil slinger.
  7. Install the timing case cover, as described earlier in this section.
  8. Install the water pump pulley and crankshaft vibration damper, as described earlier in this section.
  9. Install and properly tension the accessory drive belts. For more information, refer to .
  10. Install the fan shroud and cooling fan, as described earlier in this section.
  11. Connect the negative battery cable, start the engine and check for leaks.

Good luck... and remember rated this help.

Aug 14, 2009 | 1991 Dodge Spirit

Not finding what you are looking for?
1994 Mitsubishi Montero Logo

4,682 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...