Question about 1994 Chrysler Concorde

Open Question

94 Chrysler Concorde Cruise Control wont work.

Fuse checked and okay. Friend checked vacuum and it had same.
what next. Thanks

Posted by on

5 Suggested Answers

  • 1 Answer

SOURCE: horn,airbag light,cruise control

ON CERTAIN MINIVANS, THE DRIVER'S AIR BAG MAY BECOME DISABLED DUE TO A FAILURE OF THE CLOCKSPRING, WHICH IS LOCATED IN THE HUB OF THE STEERING WHEEL. Consequence Summary: THIS CONDITION WILL MANIFEST ITSELF THROUGH ILLUMINATION OF THE AIR BAG WARNING LAMP, AND COULD EVENTUALLY RESULT IN A DRIVER'S AIR BAG OPEN CIRCUIT, IF THE PART IS NOT REPLACED IN A REASONABLE AMOUNT OF TIME. Corrective Summary: DEALERS WILL REPLACE THE CLOCKSPRING ASSEMBLY ON ALL COVERED VEHICLES WITH 70,000 MILES OR LESS. FOR THOSE VEHICLES WITH MORE THAN 70,000 MILES, DAIMLERCHRYSLER WILL OFFER AN EXTENDED LIFETIME WARRANTY UNDER WHICH IT WILL REPLACE THE CLOCKSPRING AT NO CHARGE IF IT FAILS. DAIMLERCHRYSLER WILL ALSO REIMBURSE OWNERS WHO HAVE PAID TO HAVE THE CLOCKSPRING REPLACED ON THEIR VEHICLES. THE RECALL BEGAN ON OCTOBER 12, 2004. OWNERS SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403. A malfunctioning clockspring can also effect your cruise control,radio, wipers, and your horn relay. This can also happen one at a time til none of these are working.The solotion is to get the clockspring replaced . I DO NOT suggest you doing this on your own!

Posted on Jul 19, 2008

  • 1 Answer

SOURCE: Cruise Control Not Working, Fuse

my 1997 honda accord cruise control fuse blow and the car start up but will not go in gear. I change the cruise control fuse the car goes in gear then the fuse blow again. WHAT IS THE MY CAR PROBLEM.

Posted on Oct 24, 2008

  • 1348 Answers

SOURCE: MY HEATER WONT TURN OFF AND IT BLOWS HOT AIR EVEN

have the a/c pressure tested.if it is ok,then there is a vacuum actuator problem in the center console under the radio,it is on full heat

Posted on Jul 18, 2009

reisdos
  • 1297 Answers

SOURCE: 2001 F-150 cruise control stopped working.

really tough to do on the net but first we need to know about any codes...

Hold speed control OFF button, and turn ignition switch to RUN position. CRUISE indicator should flash once to indicate successful entry into self-diagnostic mode. If CRUISE indicator does not flash, start procedure over. If CRUISE indicator still does not flash, repair system by symptom there might be some switch concern

If CRUISE CONTROL indicator flashes once followed by 5 additional flashes, replace speed control servo/actuator.

Release speed control OFF button. Within 5 seconds in entering self-diagnostics, press speed control ON button. Press remaining speed control buttons in the following sequence; ON, RES, COAST and SET/ACCEL.

As each button is pressed, CRUISE indicator will flash.

Wait until indicator light goes out, then press next button. After sequence has been completed, indicator light will flash to indicate test passed or failed. With the codes we can then better diagnose your concern

Immediately after static test has passed, actuator performs a dynamic test by automatically operating throttle .04-.40" (1-10 mm). Observe throttle movement to witness any sticking in cable or linkage. Ensure throttle returns properly. Turn ignition switch to LOCK position. If self-diagnostics do not pinpoint fault there is more we can do but tough over the net

Posted on Mar 27, 2010

jturcotte
  • 6812 Answers

SOURCE: location of blend door or

The temperature door actuator is located at the bottom of the heater housing at the center terminal. It looks like this:

6b48b5c.gif
To remove the actuator

  1. Remove the left and right underpanel silencer ducts.
  2. Remove the two retaining screws from the actuator which are accessible from the right side of the center stack.
  3. Remove the screw from the actuator on the left side.
  4. Pull the actuator straight down from the shaft and disconnect the electrical wire. Upon removal, matchmark the shaft position of the actuator, because the shaft on this motor is keyed.

Posted on Oct 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

94 chrysler concorde, fan blower stuck on high wont turn down or off. also gas guage and other dash guages quit working. car starts and runs okay


Do you have the check engine light on?
There are some relays (I think they are in the engine compartment) that could be check. It sounds like a relay problem.
If the check engine is on, it could be a sensor, and the computer is sending the wrong information. Have it check by a professional.

Sep 22, 2015 | Chrysler Cars & Trucks

1 Answer

Why does'nt the Cruise Control Activate 2007 Chrysler Pacifica


Hi Daniel, I'm glad to help! One of the most found problems with cruise control's inoperative here at the dealership is a vacuum problem. If you do not have vacuum from the engine to the cruise control under the hood, then even though the rest of the system is working fine it will not pull the accelerator pedal. NEXT: Another problem could be that the cruise control unit under the hood is not getting power from the brake switch. Check and see if there is power at the unit's connector under the hood. If there is no power then replace the brake switch. NEXT: The PCM may not be getting a signal to apply the cruise and this mainly happens because of a cruise switch problem OR the signal is not getting through the "Clock Spring". This could be either one causing this problem, so replace the switch first because its cheaper. If all of these things check out good then it could be the Cruise Control Unit itself. Hope this helps and have an awesome day Daniel.

Jun 25, 2014 | 2007 Chrysler Pacifica Touring

1 Answer

HOW TO DISABLE CRUISE CONTROL ON 1993 CHRYSLER CONCORDE


if the cruise control is bad and you want to disable it. just pull the fuse in fusebox. if you cant find the fuse. just pull the wire connection off under hood.

Apr 20, 2011 | 1993 Chrysler Concorde

1 Answer

Where is the fuse for the cruse control on a 2003 pt cruiser


There's no individual fuse for the cruise control. If its stopped working it may be a cruise control switch or a brake light switch fault. If you have a manual gearbox, its probably a clutch pedal switch issue. Hope this helps...

Mar 10, 2011 | 1999 Chrysler Concorde

1 Answer

I had tried to use my cruise control on my 2002 pt cruiser and it wouldnt work what could it be


being that it is a 2002 I believe it will have electronic cruise and not vacuum power. so I would check your cruise control fuse and button. If all of those are OK, then its possible that the cruise control servo has gone out. That it the box that controls the throttle while engaged. You can find it by tracing the two cables coming from your throttle body. One leads through the firewall to your gas pedal, and the other will lead to you cruise control servo.

Nov 15, 2009 | 1999 Chrysler Concorde

1 Answer

MY HEATER WONT TURN OFF AND WHEN YOU TURN IT TO A/C IT BLOWS HOT AIR.. ITS A 94 CHRYSLER CONCORDE...AND I TRIED THE FUSE BUT THAT WASNT THE PROBLEM.


have the a/c system pressure tested,if it is ok,then there is a problem with the vacuum controller that controls the flip door in the console

Jul 18, 2009 | 1994 Chrysler Concorde

1 Answer

Lighter won't work/Wiper fluid sensor-94 Chrysler Concorde


u can check the fuse if the fuse is good replace the lighter assembly first check fuse and connection make sure u have 24v there

Jun 20, 2009 | 1994 Chrysler Concorde

Not finding what you are looking for?
1994 Chrysler Concorde Logo

Related Topics:

47 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...