Question about 2007 Ford Edge SEL Plus

1 Answer

The side lights and dash lights failed

This is a 1999 ford ka for a novice driver and it is not very good for the lights to fail,as the can has no manual i can not look for a solution and ford have been very unhelpful

Posted by on

  • Anonymous Feb 17, 2009

    We've checked fuses and bulbs but dash and rear lights not working. Brake lights and head lights ok.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Ford Master
  • 443 Answers

Fuses are under dash somewhere sounds like either that or under the hood is the relay box .. under the lid of the relay box it tells you which relay is which .. also your fuse box under the dash will tell you which one is which on the back side of the lid.. try this and see if it has one blown or not working properly .. always try easiest things first then if that fails go to the next step . thanks jerry holler if you need more.

Posted on Feb 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi I'm just wondering I have a ford ka 2000 and need to find were the fog light is located any help much appreciated thanks


Switch is usually located on the dash for fords on the left side of the driver. If not there then look for a rotary type switch on the signal arm or washer/wiper arm.

Jan 18, 2015 | 2000 Ford Ka

2 Answers

Firing diagram for 1999 ford f250 5.4L


okay, this should help you:
Firing Orders; (4.6L - 5.4L)
Firewall
(Passenger Side) 4 * 8 (Drivers Side)
(Passenger Side) 3 * 7 (Drivers Side)
(Passenger Side) 2 * 6 (Drivers Side)
(Passenger Side) 1 * 5 (Drivers Side)
Radiator
-------------------------------------------------------------------
Ford 4.6L Engine
Firing Order: 1-3-7-2-6-5-4-8
Distributorless ignition system
Ford 5.4L Engine
Firing Order: 1-3-7-2-6-5-4-8
Distributorless ignition system
(One coil on each cylinder)

Nov 09, 2010 | 1999 Ford F250 Regular Cab

1 Answer

Tcm how do i check no data to dash gauges including temp and gas


The issue being that over time thru vibration and such one of these solder joints will fail (happened on or 1999) you can repair this though. You will have to remove all of the trim from around the driver's side dash board, this will include the trim towards the center of the dash. Once these pieces are remove you'll need to remove the gauge panel (I believe (4) allen head screws) carefully bring the panel and release the wire clip from it. Looking at the back of the panel, where the plug was, carefully with plenty of light look for one of the pins to have a failed solder joint. It will be very faint however the failed joint will be a fine dark line around the pin. To correct use a small soldering iron and reheat this solder until it wants to flow, let it cool and reassemble.
I hope this may have helped,
Tom
PS: I have helped several persons with this issue, please review my profile; good luck with it (also often times with this issue the ABS light stays on)

Sep 12, 2010 | 1999 Dodge Caravan

1 Answer

Ford 1981 KA Laser horn fuse


LOOK IN THE FUSE BOX UNDER THE DASH ON THE DRIVERS SIDE

Nov 14, 2009 | 2006 Ford Laser

2 Answers

The odometer speedometer gas gauge and heat gauge do not work


There has been issues with the solder joints on the PIN connection to the gauge cluster. The issue being that over time thru vibration and such one of these solder joints will fail (happened on or 1999) you can repair this though. You will have to remove all of the trim from around the driver's side dash board, this will include the trim towards the center of the dash. Once these pieces are remove you'll need to remove the gauge panel (I believe (4) allen head screws) carefully bring the panel and release the wire clip from it. Looking at the back of the panel, where the plug was, carefully with plenty of light look for one of the pins to have a failed solder joint. It will be very faint however the failed joint will be a fine dark line around the pin. To correct use a small soldering iron and reheat this solder until it wants to flow, let it cool and reassemble.
I hope this may have helped,
Tom
PS: I have helped several persons with this issue, please review my profile; good luck with it (also often times with this issue the ABS light stays on)

Oct 17, 2009 | 1999 Plymouth Voyager

1 Answer

99 gmc yukon daytime running lights dont work checked the fuse but not blown dash indacator shows it is on but are not please help


Make sure Parking brakes are fully released and then check the diode under the dash, drivers side above right foot, remove diode and shunt tyhe connection if lights lite diode is bad. These diode reduce the power by 25% and are prone to fail

Sep 10, 2009 | 1999 GMC Yukon

1 Answer

Ford ka window switches not working


Check for loose wiring connections behind the door panel on the offending side.

Nov 27, 2008 | 2007 Ford Edge SEL Plus

Not finding what you are looking for?
2007 Ford Edge SEL Plus Logo

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...