Question about 2001 Jeep Grand Cherokee

1 Answer

Having Trouble! I've been trying to install the Transmission of my Jeep and it wont budge. I bought a new one since the one I had worked for only 4 mths. before it malfunctioned again. And I'm originally from Miami and took my Jeep with me to Houston and so now im here in Houston and i've been at it around this time last month.

Posted by on

  • Richard Scordino May 11, 2010

    Well, you've said a lot and told me nothing. Is the unit auto or stick? What exactly is the problem with install?



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 508 Answers

I am sure that it is an automatic. When you slipped the torgue converter into the front of the tranny you need to turn it until it engages the front pump. It will drop in to place about another inch. Also the front of the converter will need to be the correct size to fit into the end of the crankshaft and through the flex plate. If not it will never go in the last inch. Hope this helped you.

Posted on Feb 07, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Rear passenger window goes down but not up in my 95 jeep grand cherokee

pulling the window up could free it from it's mount, then you will be in trouble.
your going to have to take the door panel off and try and operate from inside. your going to have to remove it to fix the mechanism anyway.

Mar 09, 2013 | Cars & Trucks

1 Answer

A few weeks ago my 1993 jeep cherokee was having a problem shifting gears. As I looked around I noticed that the clutch reservoir was empty so I refilled it and it worked great. Yesterday, I was having the...

Your vehicle is (obviously) equiped with a manual transmission. I understand that you have been refilling your clutch resevoir, well the problem should be a leaking "slave cylinder" that is located down on the drivers side of the transmission bell housing. (If you are not mechanically inclined, and do not have the proper tools,I suggest that you take the vehicle to a mechanic to have this procedure performed.) You can purchase a new slave cylinder at your local auto parts store. You'll need to remove the old slave cylinder, There are only a couple of bolts, and one hydraulic line that attach this to the bell housing, which you'll need a "line wrench" to remove and re-install with. After removing the old part,and installing the new one, you'll need to re-fill the resevoir with the approved brake fluid,and then bleed the air from the from the system. To do this, you'll need another person to manually pump the clutch pedal from the driver seat. Once all of the air is out of the system, you should have a good pedal. Again, if you haven't done this before, I suggest that you take the vehicle to an experienced machanic.

Jan 03, 2011 | 1993 Jeep Grand Cherokee

1 Answer

1997 Jeep Grand Cherokee Laredo. While driving, I can feel hesitation in the gas peddle. Starving for fuel. I put on the brake at a stop light and the vehicle dies. Next either it will start immediately...

while its idling try wiggling the three large wires going into the pcm. if it stalls you need a pcm because inside solder joints are broken. common problem

Aug 01, 2017 | 1997 Jeep Grand Cherokee

1 Answer

I'm having trouble turning off the

push and hold the trip odometer button BEFORE turning the key on. keep holding it after you turn the key on. after about 10 seconds the light should begin flashing. when it is done flashing, the light is reset.

Nov 24, 2009 | 2000 Honda Accord

1 Answer

Jeep 1997 Wrangler. Gear shifting very hard

synchronizers are going bad a used trans would be cheaper than a rebuild due to the labor involved

Aug 19, 2009 | 1997 Jeep Wrangler

2 Answers

Jeep 1997 Wrangler. 6 Cyl Manual Having real trouble getting into gear, especially from stop. Grinding noise when backing up. Easier on gears 3/4/5 once moving. Can it be something as simple as clutch...

easy #1 check is what gear is hard when running turn car off it goes in easy probably just a clutch adj. or problem. gone unfixed can destroy the trans synchronizers

Aug 19, 2009 | 1997 Jeep Wrangler

1 Answer

Problem installing steering stabilizer for a jeep wrangler

If it's the anti-sway bar you are refering to then yes you can, just dont corner very fast, normal driving will be fiine.
I have worked on cars and found them broken and the owners didn't even know it.
Hope this helps

May 15, 2009 | 2000 Jeep Wrangler

1 Answer

92 jeep wrangler, winter in chgo, will not allow push, trans?

i found in my jeep the parking brake likes to freeze on in cold weather other than that it sounds like it could be tranny transfercase or axels seized

Dec 28, 2008 | 1992 Jeep Wrangler

4 Answers

No start

first things first,
deactivate the imobiliser and try and start it,
if it still wont budge try it manually, by shorting
out the starter.

Jul 23, 2008 | 1995 Volkswagen Jetta

Not finding what you are looking for?
2001 Jeep Grand Cherokee Logo

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides