Question about 1992 Chevrolet S-10

2 Answers

Need to find drain plug on radiator for 1992 S 10

Want to drain water, can't find plug

Posted by on

  • yadayada
    yadayada May 11, 2010

    it is on the engine side of the radiator tank, u will need to jack the car up to see the drain ****.

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

You will find it on the Inside torwards the Motor at the Bottom Passenger Side. It looks like a Wing nut Mounted on the Very Bottom. Do Not Over Torqe this when Loosening because it will not come all the Way off. Just loosen until it Stops and it will Drain the Radiator. Please Rate My Response! Thanks!

Posted on Feb 04, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

On the radiator on th drivers side on the back side of the radiator is a draincock you have to turn it to open it and it will drain

Posted on Feb 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change the radiator fluid?


Most radiators have a drain plug on the bottom tank the engine block also has a drain plug . Remove the radiator cap ,open both drains ,let all the coolant run out, if there is no radiator plug remove the lower hose , remove the heater demister hoses, with the heater control on hot flush out all the coolant from the heater radiator. with a garden hose, till the water runs clean, tighten the radiator plug or re fit the hose,put a garden hose into the radiator and flush out till the water at the block plug runs clean ,refit the heater hoses, refit the block plug, fill the radiator from the hose leave the cap off , If it has a overflow tank clean and flush it. start and run engine for 5 minutes top up radiator if needed . stop engine and drain out all water. most important that all old coolant is drained out, only buy the best coolant you can . If you make up your own use only distilled water. keep some to top up with never mix with another brand. Fill radiator with coolant top up over flow tank, run engine top up coolant as needed, refit radiator cap run for another 10 minutes check for leaks,

Oct 14, 2014 | 2006 Chevrolet Trailblazer

Tip

Flush the coolant on the 2002 tundra


PROCEDURE TO FLUSH
  • Park the Toyota Tundra on a level surface and set the parking brake. Then, with the engine off, touch the radiator to gauge its temperature. If the radiator is still warm, allow it to cool off before you start next step.
  • Twist the radiator cap one full turn, pause for a few seconds and then fully remove the cap. You want to pause to relieve any internal pressure inside the radiator. Opening a pressurized or hot radiator can cause it to spew hot coolant and burn anyone it comes into contact with.
  • Position a bucket or tray with a two-gallon capacity underneath the radiator, below the drain plug. To access the drain plug, you may have to remove the plastic engine undercover, which should be on the driver's side of the Toyota Tundra's radiator. Use a socket wrench to open the plug.
  • Open the drain plug and allow the existing coolant to drain completely into the bucket. Once complete, pour the old coolant into a sealable container for proper disposal.
  • Put the drain bucket back under the radiator and close the drain plug. Then, fill the radiator with distilled water. Next, open the drain plug to let the water flow into the bucket. Replicate this procedure until the water runs debris free out the radiator.
  • Replace the radiator drain plug and pour fresh coolant into the radiator until it's within an inch of overflowing. With the Toyota Tundra, you need to use the same coolant that came with the truck. Most likely, it is Toyota Long Life red coolant, but consult the owner's manual to be sure.
  • Start the engine of the Tundra and turn the heating fan to high. Allow it to run until the cooling fan turns on two separate times.
  • Switch the Toyato Tundra off and check the coolant level. If it is lower than before, add more coolant. If not, put the radiator cap back on and close the hood.
TIPS
  • You will need 2 gallons of coolant for the four-valve Toyota Tundra and 3 gallons of coolant for the six-valve model.
  • Using tap water from a hose is an alternative to flushing with distilled water, but tap water can leave sediments behind that can damage your coolant system
WARNING
  • Because coolant is extremely toxic to people and pets, it's imperative that you dispose of the old coolant properly.

on Mar 17, 2010 | Toyota Tundra Cars & Trucks

1 Answer

HOW THE COOLANT SISTEM FLOW ON 2001 FORD WINDSTAR. I TRY TO FLUSH THE RADIATOR BY REMOVING THE DRAIN PLUG BUT THE WATER WONT DRAIN, I REMOVE THE THERMOSTAT THINKING IT'S COULD BE THE PROBLEM BUT...


Remove drain plug from radiator by unscrewing, if this does the trick you are on your way if not, take a tooth pick and pick at the hole. if this fails and you still need to drain radiator, let it sit until it cools down then remove lower radiator hose..This will remove all coolant from block and radiator.

Oct 02, 2011 | Cars & Trucks

1 Answer

Flushing antifreeze on a 2006 kia sorento


This procedure makes a bit of a mess and requires catch pans but it is the best way to flush a coolant system without cutting any hoses or adding a flush kit.


If your radiator does not have a drain plug is to remove the LARGE lower radiator hose and drain the anit-freeze. (Even if it does have a drain plug the steps below are the best way) You then plug the lower radiator hose connection on the radiator and have a 2nd person add water to the radiator with a hose. They will need to place a rag over the fill port for the radiator and flush the block until you get clear water from the lower drain hose. Once you get clear water drain off the fresh water by unblocking the lower radiator fitting and flush the radiator. Once you get cleanwater from the radiator connection, reconnect your lower radiator hose. (Tighten the clamp!) Then add your anti-freeze. Remember there will still be a some water in the block so do not be afraid to keep your anit-freeze / water ratio a tad higher because the left over water in the block will dilute it slightly.

Thanks for choosing FixYa,
Kelly

Aug 01, 2011 | 2003 Kia Sorento

2 Answers

I want to learn how to drain and flush my radiator. I need help on how to do so without making as mess


well its bound to make a little mess but you should have a drain plug on the radiator at the bottom towards the engine side on one of the 2 tanks (sides of radiator ) unscrew drain plug and let drain into a pail or pan ( 2 gallon ) after it drains remove lower radiator hose. use a garden hose and fill radiator and let it flush for a little, hook lower radiator hose back, tighten drain plug and fill with a 50/50 mix new antifreeze,

Feb 07, 2011 | 1996 Ford Taurus

1 Answer

How to replace coolant for nissan altima 2006


Park the Nissan Altima on a flat surface and set the parking brake. Next, open the hood and check the external temperature of the radiator. If the radiator is warm to the touch, wait for the radiator to cool before you continue.

Twist the radiator cap one turn to relieve any pressure. Step back from the radiator and allow a few seconds to pass, and then completely remove the radiator cap.

Place a bucket or tray with at least a 2-gallon capacity underneath the radiator and below the drain plug. The drain plug on a Nissan Altima is on the passenger side bottom of the radiator.

Loosen the drain plug and let the old coolant drain completely into the bucket. Take care while loosening the drain plug, because it's plastic and can be brittle. Pour the old coolant into a sealable container for proper disposal later and put the bucket back under the drain plug opening.

Close the drain plug and pour distilled water into the radiator until it's full. Then, open the drain plug and let the water flow into the bucket. Keep repeating this procedure until the water runs clear and debris free into the bucket. You will need at least 3 gallons of distilled water.

Make sure to tighten the drain plug and fill the radiator with fresh coolant. Refill the radiator to within an inch of it overflowing. Check the drain plug and hoses for any possible leaks.

Start the Nissan Altima and turn the heater to the high setting. Let it run for about 10 minutes and shut the engine off. Check the coolant level and refill, if necessary. Finally, put the radiator cap on and close the hood.

Oct 23, 2010 | 2006 Nissan Altima

1 Answer

How to replace the radiator fluid


- Make sure the engine is cold and not running.
- Drain the radiator fluid by opening the drain plug at the bottom of the radiator or for a better/faster drainage and cleaning, carefully remove the bottom radiator hose by first loosening the hose clamp.
- Open the radiator cap and water rinse/flush the radiator core via a garden water hose until you no longer see any dirty water coming out of the bottom hose (or drain plug).
- Flush the radiator over flow (plastic) container by overfilling it with your garden water hose.
- remove garden water hose, carefully refit the bottom radiator hose, tighten the bottom radaitior hose clamp, refit/tighten the radiator drain plug.
- refill the radiator with approved radiator fluid for your climate and also refill the radiator overfow tank to the indicated level..
- Refit radiator cap
- Start your engine until it warms up and check for any water or steam leaks. Refit and or replace any faulty hoses or radiator (regulator) cap!
It is not difficult and have fun!

Dec 25, 2009 | 2003 Volkswagen Beetle TDI

2 Answers

How do I flush the coolant on the 2002 tundra V6?


PROCEDURE TO FLUSH
  • Park the Toyota Tundra on a level surface and set the parking brake. Then, with the engine off, touch the radiator to gauge its temperature. If the radiator is still warm, allow it to cool off before you start next step.
  • Twist the radiator cap one full turn, pause for a few seconds and then fully remove the cap. You want to pause to relieve any internal pressure inside the radiator. Opening a pressurized or hot radiator can cause it to spew hot coolant and burn anyone it comes into contact with.
  • Position a bucket or tray with a two-gallon capacity underneath the radiator, below the drain plug. To access the drain plug, you may have to remove the plastic engine undercover, which should be on the driver's side of the Toyota Tundra's radiator. Use a socket wrench to open the plug.
  • Open the drain plug and allow the existing coolant to drain completely into the bucket. Once complete, pour the old coolant into a sealable container for proper disposal.
  • Put the drain bucket back under the radiator and close the drain plug. Then, fill the radiator with distilled water. Next, open the drain plug to let the water flow into the bucket. Replicate this procedure until the water runs debris free out the radiator.
  • Replace the radiator drain plug and pour fresh coolant into the radiator until it's within an inch of overflowing. With the Toyota Tundra, you need to use the same coolant that came with the truck. Most likely, it is Toyota Long Life red coolant, but consult the owner's manual to be sure.
  • Start the engine of the Tundra and turn the heating fan to high. Allow it to run until the cooling fan turns on two separate times.
  • Switch the Toyato Tundra off and check the coolant level. If it is lower than before, add more coolant. If not, put the radiator cap back on and close the hood.
  1. TIPS
  • You will need 2 gallons of coolant for the four-valve Toyota Tundra and 3 gallons of coolant for the six-valve model.
  • Using tap water from a hose is an alternative to flushing with distilled water, but tap water can leave sediments behind that can damage your coolant system
WARNING
  • Because coolant is extremely toxic to people and pets, it's imperative that you dispose of the old coolant properly.

Nov 14, 2009 | 2002 Toyota Tundra

1 Answer

How do you drain radiator?


Draining water from your radiator? Take a look at the
bottom portion of your radiator and find a screwed plug.
Just unscrew this, and drain the water. Take care that
you do not do this while the engine is still hot, water coming out is HOT.

Oct 17, 2009 | 2005 Nissan Quest

2 Answers

Where is drain plug for 1998 dakota 4x4 i need to drain radiator &what is the turning thing on the lower drivers side of radiator 4


1998 dakota 4x4
You can remove the drain plug in the bottom on the radiator.
You can remove the lower radiator hose. Since the vehicle is 10 years old you may want to inspect the hoses for replacement anyway.

) Make sure the vehicle is cool.
) Slightly loosen the radiator cap to release any pressure.
) Re-tighten the radiator cap.
) Place a suitable container under the drain point.
) open the drain.
) Re-loosen the radiator cap again.
) Allow to drain.
) REPLACE THE DRAIN PLUG.
* At this point the radiator can be fill with water and a radiator cleaning agent- run the engine - allow to warm up.
* Re-drain the radiator - .
) REPLACE THE DRAIN PLUG.
) Refill the radiator with water/anti-freeze.
) Dispose of waste fluid according to the local regulations. Some city dumps will accept it. Some parts stores may accept it. Do not pour down the drain or dump on the ground.

Apr 19, 2009 | Dodge Dakota Cars & Trucks

Not finding what you are looking for?
1992 Chevrolet S-10 Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...