Question about 1996 Chevrolet Blazer

1 Answer

Rear Window Glass won't Release

Turn the key but the window doesn't open.
Don't hear click.....fuses good.
How can I release the glass to access the solenoid??

Posted by on

  • bizzyman45 Feb 04, 2009

    Does the window glass release with a solenoid or a motor?

    I will pull the dash panel and check the relay.


  • Roberta Smith
    Roberta Smith May 11, 2010

    what solenoid ? or do you mean the window motor.... first check the relay in the fuse panel under the dash

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Followed owners manual for emergency opening of rear window glass.
Removed upholstery panel from the tailgate once glass was opened. Found a broke (plastic) actuator arm on the actuating motor.
Ordered new one for replacement.

Posted on Feb 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

On my 1997 Blazer the rear hatch class wont open by key or botton so what could i do to fix it


The easy way to open the glass without tearing up the tailgate panel or ripping out your carpet:

Pull back the interior tailgate panel right above the bump in the middle where the latch is. There are no screws or boltsicon1.png in that area, so it should pull away about 2 inches. Then you'll have to reach in and push down the release bar. You should be able to feel for the part that needs to be pushed down to release the glass. Now that it is unlocked, you will be able to open the hatch and the tailgate. Once open, remove the interior tailgate panel, which has one screw on each side.

The failed actuator that needs to be replaced is not all that expensive and can be found at the dealer.

Dec 10, 2014 | 1997 Chevrolet Blazer

1 Answer

Fix for the door glass,2009 CHALLENGER. Won't reset to down position when opening door to allow window to break seal.Then move up and seal glass when door is closed. SMart Glass?


This may be as simple as relearning the window stop positions. Perform the following procedure to relearn the windows;

1) Sit in the drivers seat and ensure both doors are fully closed.
2) Turn the key to the ON position but do not start the vehicle.
3) Pull up on the drivers window switch until the window reaches the full up position, then CONTINUE HOLDING THE SWITCH UP for 2-5 seconds, then release the switch.
4) Push down on the drivers window switch until the window fully opens, then CONTINUE HOLDING THE SWITCH DOWN for 2-5 seconds, then release the switch.
5) Repeat steps 1-4 for the passenger window.
6) Close both windows and check the operation of the smart glass.

Let me know if you need further help.

Nate

Oct 18, 2014 | 2009 Dodge Challenger

1 Answer

97 jimmy rear glass won't open


if you can hear the motors its probabley the glass come of the runner or the wire has snaped remove the rear door card and have a look its should be easy to tell if its snaped or not get some one to press the button and watch how it works either replace wire or put glass back on runner hope this helps ivan

Oct 01, 2012 | Chevrolet Cars & Trucks

3 Answers

My back automatic window went down and now won't come back up. No sound from motor. Checked fuses. Even took back seat apart but don't know what to do or what caused it. How can I get window to go...


it may need to be reset.

SECTION 501-11: Glass, Frames and Mechanisms 2001 Explorer Sport/Sport-Trac Workshop Manual
GENERAL PROCEDURES Rear Window Motor Initialization s1r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.
NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.
NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.
NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.
NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.
NOTE: Steps 7 and 9 require that the power rear window control switch be held in the closed position until the power rear window motor stalls the window in the upper header seal. Step 8 requires that the window control switch be momentarily turned to the open position.
  1. Start with the ignition in the OFF position.
  1. Turn the ignition to the ON position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the OFF position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the ON position. The power rear window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialized mode.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls in the upper header seal.
  1. Momentarily rotate the power rear window control switch to the open position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls into the upper header seal. Once this operation is complete, the window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.
  1. Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions.
------------------------------------------------------------------------------------
  • The power rear window is inoperative (Explorer Sport Trac only)
  • Circuitry.
  • Battery Junction Box (BJB) fuse 3 (30A).
  • Central Junction Box (CJB) fuse 20 (7.5A).
  • Power rear window control switch.
  • Rear window glass motor.
  • Go To Pinpoint Test K .

------------------------------

Sep 15, 2011 | 2001 Ford Explorer Sport Trac

1 Answer

I need to remove nearside rear door window from Ford Focus 2003 , it has electric motor gear but I am unable to get the peg to push out from the plastic block which holds the window glass in, how do I get...


SECTION 501-11: Glass, Frames and Mechanisms 2003 Focus Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/24/2003 Rear Door Window Regulator and Motor adobe.gif Printable View (208 KB) Removal and Installation
  1. Remove the rear door speaker. For additional information, refer to Section 415-03.
  1. Remove the side impact bolster.
    e0001157.gif
  1. Position the door latch release handle aside.
    e0001156.gif
  1. ani_caut.gif CAUTION: Do not touch the adhesive surface, as re-bonding will be impaired.
    Remove the watershield.
    e0001158.gif
  1. Connect the window operating switch electrical connector.
    e0001851.gif
  1. Align the regulator clamp with the access hole.
    e0008374.gif
  1. Remove the window glass from the regulator clamp.
    1. Push out the pin.
    1. Push out the sleeve.
    1. Remove the window glass from the regulator clamp.
    e0001854.gif
  1. ani_caut.gif CAUTION: Make sure the window glass is adequately supported at the top of the opening.
    Using suitable hooks, raise and secure the window glass.
    e0001855.gif
  1. Disconnect the window operating switch electrical connector.
    e0001851.gif
  1. Disconnect the motor electrical connector.
    e0001856.gif
  1. Remove the bolts and the motor and window regulator.
    e0008353.gif
  1. To install reverse the removal procedure.

Jul 26, 2011 | 2003 Ford Focus

1 Answer

Troubleshooting rear lock on 1999 GMC Envoy


There are some mechanical rods in the rear hatch that are probably rusty and you will have to take the inner panel off to acces and clean them to get them moving to operate the lock.

May 09, 2010 | 1999 GMC Jimmy

1 Answer

Cant open the rear door of my freelander because the window will not go down


1st you need to get the window down are all fuses good ....if so you can get the inside panel off and gain access to the motor is the motor bad well you'll need to use a test light and determine power to it with a good ground and test with the key in the on position if power is present then make sure the connection is solid and work the window button if the trunk itself is not fully closed the window switch may not work as well after all above is checked remove the bolts from either the window itself 10 mm i believe or 7/16 wrench to remove the glass then you may open the lid and repair as needed and reassemble the glass close the lock_s itself and use teh switch to drop window down and then pull on the release handle to open the locks back up n close lid hatch and ensure the proper working of the window you may need to adjust the window one way or the other for alignment and if working good at this point reinstall the rear panel and yer done

Sep 07, 2009 | 2002 Land Rover Freelander

2 Answers

How do you open the rear window on a 1995 gmc jimmy


There is a small plunger on the tailgate, see if that is still doing it's job to push the glass out abit. the other thing too is if the two pistons that hold the glass up is weak can do that and if the car has been out in the sun for a while, i find that the weather strip hold the glass down. Good luck and let me know how your did. 

Apr 05, 2009 | 1995 GMC Jimmy

2 Answers

Rear Window Glass won't Release


what it seems to me is that your latch is stuck in a locked posiiton. If so, open the hatch itself to expose the screws in the inside panel. Once you have removed the screws the pry the bottom and sieds of the panel away from the body using a panel popper or flat screw driver. Then while applying upwards pressure to the panel from the bottom give the upper part of the panel a quick pop with the heel of your hand.. this should release the panel from the body, this will expose the latch itself. Using 10 millimeter socket, remove the latch from the body thus allowing you to remove it in a safe manner.

Apr 05, 2009 | 1995 GMC Jimmy

1 Answer

Rear window defroster


you need to make sure the wires are on the glass on each side and there is no broken wires in the glass there is a repair kit at a auto store to fix if you have a volt meter test it and that way you can find the problem look for breaks in the wire in the glass and do not for get the wires on each side of the glass.

Feb 11, 2009 | 1997 Ford Taurus

Not finding what you are looking for?
1996 Chevrolet Blazer Logo

397 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

71231 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7001 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...