Question about 1999 Chevrolet Suburban

1 Answer

Broken door handle

Broken drivers inside door handle. How do I take off the ring around the handle? I have figured out the rest of the door, except this part.

Posted by on

  • Anonymous Mar 29, 2014

    Drivers door handle

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Inserted a small screwdriver between the ring and the handle assembly. There are three tabs that needs to be released. One on top, one on bottom and one on end(opposite of the locking lever). After that. the ring simple popped off.

Posted on Feb 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hoo.com need to change a door handle on a 1999 chevy surburban and am having trouble


Inside door handle? unscrew two screws in arm rest, then lift the back of the window switch up and unplug everything, then insert a small screw driver to pop the small taps loose around the outer edges of the door handle trim ring, then lift the door panel straight up. drill the rivet out and slide the handle forward

May 24, 2011 | 1999 Chevrolet Suburban

1 Answer

Broken handle on outside of rear sliding door 2005 toyota sienna. Cannot figure out how to get the door panel off from the inside to access it.


THE PANEL HAS NAPS THAR GOES INSIDE OF THE METAL AROUND THE PANEL YOU WILLNEED A SMALL SCREW DRIVER TO STICK IN BETWWEN TO GET A LITTLE OPEN AND PULL IT OFF CAREFULLY

Mar 09, 2011 | Toyota Sienna Cars & Trucks

1 Answer

The front driver side door's outside handle on my 1996 Ford Explorer became very loose. It still works but I wanted to know how to take off the door panel to look inside to see how I can fix it. Thanks


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Pull back the weather seal and you'll be able to get to everything. Either the bolts holding the outer handle on has broken or fallen out, or the handle anchor (plastic) has broken

Sep 18, 2009 | 1996 Ford Explorer

3 Answers

The inside door handle does not open the door. I can open it from the outside but not the inside.


I just fell into the same situation. My interior driver's door handle just does nothing all of a sudden. I went on the Mazda Forum website and came away with at least a temporary fix.
The lock switch can be used to open the door from the inside by pushing it the opposite way it's pushed when locking the door. In other words, the rear portion of the lock switch needs to be depressed and the front portion needs to be pulled away from the door. It may be difficult to do with the trim piece around the lock still on. The trim piece can be removed by pulling the small plastic cap away from the base (it's on a plastic hinge) off and unscrewing the holding screw underneath it. Pull the handle away from the door and the trim piece will come right off.
I'm using that as a temporary solution now until I get a new/used door assembly.
Hope that helps.

Sep 02, 2009 | 2001 Mazda Tribute

1 Answer

Can't open driver side door from outside--only the inside--I need to know how to get paenl off to get to door latch--or how to fix the problem


undo all fittings on door trim [arm rest] etc.
panel has pressure plugs so be carefull pulling on the trim to release it from the door!
somtimes you may just have to wiggle a bit
so start on the corner first& work it loose all the way around
check the rodsto the door handle & lock mechanism is still attatched or thtat the handle has broken off the tab that moves the rod

Jul 18, 2009 | Volvo 240 Cars & Trucks

1 Answer

Drivers side door on my jeep cherokee will not open from inside


most likely the inner door handle has a broken hooking tab for the rod to the latch plate.most door panels are held in place with a few screws around the door pull handle and arm rest than most of the sides and bottom of the door panel are held by plastic snap clips. with a large straight blade screw driver start at a corner of the door panel , slide the blade of the screw driver under the edge of the panel and lightly pry out untill you lossen up one of the clips than slide along the screw driver to the next clip , keep going till the panel is lossened up.

Mar 29, 2009 | 2000 Jeep Grand Cherokee

1 Answer

How do I remove the door panel on a 97 Volvo 960 wagon


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door.. It sounds like the linkage connecting to the outside handle may have come off or broken

Mar 07, 2009 | 1997 Volvo 960

1 Answer

Remove inside door panel without breaking it


they have push in clips that hold the panel on the door you can pull it off with your hand or go to parts store and buy a door panel removal tool
PLS take time to rate this solution and by the way you will probably need to buy new push in clips to hold panel on

Feb 17, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

Drivers side door will not open from the outside


check your outside door handle to see if it is broken if not adjust the rod to the handle,they are adjustable, make the rod longer,to do this unhook the rod from the door handle and screw the adjuster counter clockwise one turn and try it, if still wont work give it another turn, 2 turns should fix it.

Feb 06, 2009 | 1997 Oldsmobile Cutlass Supreme

1 Answer

Door Panel removal


remove all visable screws from panel and arm rest. Arm rest should come off. Use a flat thin tool or piece of metal and slip it between the panel and the metal door frame. Slip it in about 2 inches,. Slide it back or forth til you hit a stop. That should be a plastic pop in.twist metal tool to pull panel away from the door. It should pop away from door frame. Don't overdo it if it doesn't come out. try another spot. once you get one loose, you can tell how to get the others out. Once panel is loose push it upwards to get top lip out of window bottom. If it has power windows,disconnect plug. If it has manual windows, you will have to remove the window crank There is a snap ring behind window crank that has to be removed.push in on panel by window crank and you can see the ring.

Dec 06, 2008 | 1998 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...