Question about 2002 Mercedes-Benz C-Class

1 Answer

Won't turn on

It only does it does it sometimes that it won't want to turn on
i went to the movies after the show it wouldn't turn on after 10 minutes it turned on or in the morning it won't turn on

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 61 Answers

Their could be a bad ground to motor. Check the ground to the motor, it should go right from the battery to the motor.

Please contact me if your problem presists.

Thanks, Charlie

Posted on Feb 04, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 98 Sentra does not turn over


Has the battery been load tested? do that first.

Apr 30, 2017 | 1998 Nissan Sentra

1 Answer

91 Cherokee will crank but won't fire. Replaced


how much is the RPM showing in the datatlogger while cranking?

Dec 03, 2012 | Cars & Trucks

1 Answer

I have a 97 Crown Vic/w police interceptor....I asked a question several days ago because of issuses I'm having with my car. The car starts sometimes, with no problems. Other times...it won't...


Sounds like its a starter problem,if you can pull the starter off take it to an auto parts store,

there are many locations that have equipment to put a load on the starter, and they will be

able to tell if its bad. once you pull the starter off, if you can check the teeth on the fly wheel,

if there is a dead spot, the starter could spin and not engage the flywheel. I hope it's the

starter. the bendix on the starter the teeth that engage the flywheel could also have dead

spot's. and not engage all the time. good luck!

Jul 27, 2011 | Ford Crown Victoria Cars & Trucks

1 Answer

I am hoping someone on here can help me with my problem...My check engine light came on my 2003 Chrysler 300 M special edition and also wouldn't start at times for up to 30-45 minutes at a time, and...


Have you had the battery changed since you had the car. Have that checked for a full charge and no dead cells. Always have the air-conditioning completely off when starting the car. The starter takes a lot of amps to turn over and having the AC on doesn't help.

and another reason is the code didn't clear out completely. this tool can help you test the code.

Jun 22, 2011 | 2003 Chrysler 300M

1 Answer

Replaced stock bcm with used. Was reprogramming with the method of turning key to start position (vehicle won't start) then leaving it in the on postition for approx 10 minutes until the theft lock...


A used body control can be used in a vehicle other than the vehicle it was installed in. the body control module when first installed is programmed with the vehicle vin number. the vin number can not be changed was it was written to the BCM. the oprions can be always change in the BCM but not the VIN number. basically the used bcm you have installed has the vin number from the vehicle was installed in, now the vin number in the used BCM doesnt match all the other control modules

Jun 07, 2011 | Chevrolet Equinox Cars & Trucks

1 Answer

2004 Range Rover HSE won't start. Last week i had problem starting the rover. I checked the starter and the relay and was hoping that it could be one or the other. But this week i noticed that the...


Sounds more like a low voltage current flow in the ground circuit(harness).
Or the voltage output from ignition switch.
If No check engine light ever came on, or is not on, then the PCM/ECM is telling us there is No fault anywhere,
TCM-automatic transmission computer- uses VSS- vehicle speed sensor, to know when to shift gears.
A low input power to any of these control modules would result in lack of performance
Rough shifting could be caused by low fluid level

1. Check all fuses
2. ensure the battery cables are tight.
3. Check negative from battery has ground to frame rail
4. Check Transmission Fluid Level.

If you notice other symtoms, or situation continues, please post back

Mar 02, 2017 | 2004 Land Rover Range Rover

1 Answer

2004 Sante fe 3.5L 2WD went out to go to work and wouldn't turn over, (assumed dead battery), went down and got new battery and installed, still wouldn't turn over, (assumed starter shot),removed...


TEST POWER LEADS TO STARTER FOR POWER
AT STARTER (BATTERY POSITIVE TO STARTER BATTERY NEGATIVE TO ENGINE BLOCK)
THEN TEST FOR SIGNAL POWER TO SELENOIDE ON STARTER
(KEY TURNED TO START POWER SHOULD GO TO SELENOIDE)
IF NO POWER TO SIGNAL WIRE CHECK FUSES AND RELAYS
ON STARTER CIRCUIT
IF THIS CHECKS OUT MAY BE AUTO TRANSMISSION NUTRAL PARK SWITCH
TRY TO START IN NUTRAL OR WHILE SHIFTING TRUE GEARS SLOWLY WITH SHIFTER
IF STANDARED CHECK NUTRAL SAFETY SWITCH

May 08, 2011 | 2004 Hyundai Santa Fe

Not finding what you are looking for?
2002 Mercedes-Benz C-Class Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

yadayada
yadayada

Level 3 Expert

70387 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...