Question about Hyundai Motor 2002 Elantra

2 Answers

Handbrake adjustment? I have a hyundai accent 1.6.I have changed rear brake shoes but handbrake still not holding.Can any body tell me what the problem is please?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 21,949 Answers

You havent set the rear brakes up properly,slacken off handbrake cable first,remove the rear shoe any side first or both together ,firstly with a small angle grinder flaten the lip thats built up around the edge of the drum ,taking care not to catch the shiney facing.then look at at the handbrake pulling arm and make sure it right the way back onto the shoe .Next the hard part and this is adjusting the the automatic adjuster till as you put drum on their is a slight resistance sliding over shoes but the drum turns with a slight resistance and a bit of noise where the shoes are just catching,Do both side sides and adjust handbrake till you have 3 notches (clicks) .check wheels still turn ok with a slight noise of the shoes dragging .Now footbrake should be firmer and this car will lock back wheels up at 30mph ,and bounce out the brake tester at the annual mechanical inspection

Posted on Feb 04, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 73 Answers

There is a cable tha runs to each break . sometimes the cables are adjusted from the handle just move the cover from the lower part of the lever and check the cables i think it's a 7/16th bolt you use to adjust the cable might be a 1/2 in

Posted on Feb 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace the rear break drums on a hyumdai accent gs


Brake Drums-They seem to be fastened with a nut and have bearings that need to be regreased based on the diagram found for replacing the shoes. Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Wheel 02-04_hyundai_accent_brake_drum.gif

    • Brake drum
To Install:
  1. Install or connect the following: 02-04_hyundai_accent_brake_drum.gif

    • Brake drum
    • Wheel
--- Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Wheel 02-04_hyundai_accent_brake_drum.gif

    • Brake drum 02-04_hyundai_accent_rear_brake_backing_plate.gif

    • Shoe hold-down spring
    • Automatic adjuster spring
    • Adjuster lever
    • Shoe adjuster by spreading the shoes
    • Shoe to shoe spring
To Install:
Note: Apply the specified grease to the shoe to backing plate and shoe to anchor plate contact surfaces.
  1. Install or connect the following: 02-04_hyundai_accent_rear_brake_backing_plate.gif

    • Shoe hold down pin
    • Return spring to the push rod while it is shortened
    • Shoe hold down spring
    • Shoe to shoe spring
    • Shoe adjuster by spreading the shoes
    • Adjuster lever
    • Automatic adjuster spring 02-04_hyundai_accent_brake_drum.gif

    • Brake drum
    • Wheel
Note: After assembling the drum components, pull the parking brake lever all the way up several times
prev.gif next.gifprev.gif next.gif

Sep 30, 2010 | 2001 Hyundai Accent

1 Answer

How to adjust handbrake on Hyundai Accent 2000


adjustment will be done on the rear brake shoes

Jun 30, 2010 | 2000 Hyundai Accent

1 Answer

Does the abs sensor have to come off to change rear brake shoes on accent?


hi from the uk in answer to your question you do not need to disconnect or remove the abs sensor you just remove the brake drum from the hub then remove shoe locating springs that retain shoes to backplate then lift off and remove bottom return spring this then allows you to slip the brake shoes off w/cyl at top complete with spring and auto adjuster ? then to remove the handbrake cable just pull the shoe and the quadrant lever apart so cable can be lifted out of the hook up on lever ? you can now interchange shes/springs /adjuster on your bench ? also run te adjuster wheel back on thread to off position this will enable you to fit shoes back to backplate and moreso help in fitting cable to its hookup ? when brakeshoes are refitted ? and centralized on back plate ? you can manuall rotate the adjuster wheel and keep tryin the drum for fitting and rotating with no binding trial/error method when satisfied ? refit screws to secure drum then do same with other side when completed you must bleed both wheels this will improve b/pedal your handbrake will also be better/less travel when applied hope these instructions help you ? best wishes from uk

Mar 16, 2010 | 2000 Hyundai Accent

1 Answer

How do i adjust 1996 excel handbrake


first thing to check is the rear shoe linings for wear. if they are to worn the handbrake would be very loose. this is where you adjust the brake. there is a shoe adjustment in the drum.

Jan 23, 2010 | Hyundai Excel Cars & Trucks

1 Answer

I just got my handbrake adjusted in my hyundai excel. whenever i pull up on a slope it still rolls back with the handbrake on


If the hill is steep or is covered with dirt or sand then you may not have a problem. Did you park there before and it held? Do you use the hand-brake all the time? Have there been times that you forgot to release the parking brake? When the shoes were adjusted were the shoes inspected before the adjustment? The tech. should have looked for problems.

Nov 11, 2009 | 2001 Hyundai Accent

1 Answer

Rear brake on 2002 hyundia accent


hi from uk after supporting car on stand or blocks ? remove wheel then you will see x head screwsx2 remove screws then release handbrake drum should now rotate freely you may need to lightly but firmly tap the drum off the hub if you have an old vac ? use it to vac the dust from shoes and drum ? if your shoes are ok ? then make sure the auto adjuster is free and clean? if your h/brake travel is high and the reason for checking brakes? then notch up auto adjuster a couple of clicks at atime whilst keep trying the drum fits so the shoes are just enabling rotation of drum by hand then press b/pedal a cople of times to centralise shoes to drum ? if drum still rotates freely with no binding on shoes ? then re assemble carry out same proceedure on other side ? do not adjust brake cable! unless you do adjustment as above you may/will find your h/brake is better /less travel ? also your foot brake will feel better and less travel ? hope this helps you but if you req further info/assistance by all means come back to board best wishes from lancashire uk

Jun 04, 2009 | 2002 Hyundai Accent

1 Answer

Knocking when brakes applied


REAR BRAKE NOISE - SHOE AND LINING KIT
A shoe and lining kit is available for installation if an Elantra (XD) or Accent (LC)
equipped with rear drum brakes exhibits a chattering noise from the rear brakes when
the brakes are applied.

APPLICABLE VEHICLES:
• Accent (LC) and Elantra (XD) equipped with rear drum brakes and in the following
Production Date and VIN Range:
SERVICE PROCEDURE:
For further information, refer to the applicable Shop Manual.
Model Production Date Range VIN Range
ACCENT (LC) May 21,1999 - Dec. 28, 2005 ALL WITH DRUM
BRAKES.
ELANTRA(XD) June 30, 2000 - May 23, 2006 JOB#1-
KMHDN46016V363974

ACCENT SHOE & LINING
KIT
ASSEMBLY
58305-25A00 58305-25F00 7"(00MY - 05MY)
58305-25A10 58305-25F10 8"(00MY - 05MY)

May 03, 2009 | 2003 Hyundai Accent

1 Answer

2003 Hyundai Accent Rear Brake Noise


the rear shoes need to be cleaned and adjusted. nothing to worry about unless it annoys you too much.

Mar 29, 2009 | 2003 Hyundai Accent

1 Answer

Handbrake problem


hi fro uk when you reassembled brake shoes? did you notice the tubular bar just below b/cylinder? it fits between the two shoes and has a toothed wheel on the treaded side(l/h) this is the auto adjuster ie as tooth wheel is rotated it extends the treaded side thus adjusting shoes to drum o/k? this is normally done auto by the small lever below but when fitting new shoes you must adjust this rod with tooth wheel and keep trying drum fitting when you can fit drum /just? fit and press brake to centralise shoes to drum then adjust again if req'd so that drum fits and rotates withh shoes not binding ?? do both sides THENyou willdrums fitted you will feel b/pedal is improved ie less travel on braking ? SO FIRST THING YOU HAVE TO DO IS SLACKEN OFF H/BRAKE CABLE ADJUSTMENT /SLACK ? then proceed with the above instruction afterwards if you do as above then you pull h/brake up one notch ? then adust slack from cable to light tension release h/brake and ensure wheels rotate freely when you apply h/brake it should hold on approx four//five notch ? hope this helps

Feb 04, 2009 | Hyundai Motor 1998 Accent

3 Answers

Remove rear brake drums


0f2c8a8.gif
1. After removing the wheel, remove the brake drum. 2. Remove the shoe hold down spring, the automatic adjuster spring and adjuster lever.
7b7d17f.gif
3. Spread the shoes and remove the shoe adjuster. 4. Remove the shoe to shoe spring and shoe hold down spring.
a1a62c3.gif

Jun 03, 2008 | 1999 Hyundai Accent

Not finding what you are looking for?
Hyundai Motor 2002 Elantra Logo

1,093 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

61292 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...