Question about 1998 Chevrolet S-10 Pickup

1 Answer

Blower motor won't work on 4

It works on 1,2,3 but not 4

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 91 Answers

On most gm cars the blower motor from 1-3 goes through a set of resisters to make the motor run slower, for four it's a straight through relay, replace the relay and your good to go.

Posted on Feb 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Heater won 39 t blow on 5


haw i fix my rpm meter problem

Sep 28, 2013 | Cars & Trucks

1 Answer

Heater won`t work at 1,2,3 settings, it only works on #4 setting (chrysler,sebring 2003)


sounds like a blower resistor. usually it is on the passenger side under dash near blower motor and hvac box. the resistor add resistance to the circuit to slow the blower motor, if it is inop then you only get high speed.

Dec 30, 2012 | 2003 Chrysler Sebring

1 Answer

Air condition and heat won't work


Check to see if you are getting voltage to the blower motor if you are the motor is bad if not check the fan speed switch. 1 2 3 or low medium high if you get voltage going to the switch but not from replace the switch if you have voltage from switch check the blower motor resistor the although with the blower resistor you commonly have a high fan speed in the max setting and the lower speed settings don't work wich would make you think 1 2 3 are not working but 4 is. That is why it is best to check all parts to make sure the part you do replace needed to be replaced

Oct 15, 2012 | 2000 Ford Focus

1 Answer

2005 Trailblazer EXT. Blower speed control not working...


Problem with blower motor is the blower motor resistor. They are usually located next to the blower motor, a couple of screws and a couple of plugs and your done. Autozone sells them for around $30 each. Wipers you may want to check for relays under the hood in the fuse block. There may be 2 relays 1 for low and 1 for high. I have switched relays from other working accesories and got wipers to work. Sometimes bad connection.

Mar 19, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

The HVAC blower fan on my 2001 Pontiac Aztec stopped working on settings 1-3 several weeks ago. Last week it stopped working at setting 4 and today it stopped working all together. What is the most likely...


the blower not working on settings 1-3 is the blower motor resistor. this limits the power provided to the blower motor itself to change the speed. at setting 4 it is getting full power. since it quit on 4 also, i would still say the resistor needs to be replaced first, then see if the blower comes back. you may also need a blower motor. if you have a voltmeter you can just turn the switch to 4 and see if the motor is still getting 12 volts. if it is and doesn't run, it needs a blower motor too. if it's not, then its just the resistor

Feb 24, 2010 | 2001 Pontiac Aztek

1 Answer

Heater only works on 5 settings 1-4 don't work


you need to change your blower motor resistor it should be located neer or on the blower motor housing.

Dec 30, 2009 | 2000 Chevrolet Impala

1 Answer

Speedometer and Heat blower not working


The fan motor has gone out,it was bad before it went out,drawing too many amps,so it took the blower motor resister out with it.The resister is next to the blower motor.On the speedo,check,or replace the speed sensor in the transmission,

Nov 20, 2009 | 2000 Ford Focus

1 Answer

Why does the blower motor only work on spped 4 and


Usually when the blower only works on the higher speeds, the blower motor resistor has gone bad. This should be located somewhere near the blower motor itself, it is usually bolted to the blower motor housing (or in that area), just unbolt it and you can replace it. Hope this helps

Jul 17, 2009 | 2001 Chevrolet Silverado

1 Answer

Switch for blower motor for heat & ac


Sounds like you need a blower motor resistor. It has bad paths between the 1 and 2 speed circuits.

Jun 02, 2009 | 1999 Oldsmobile Alero

2 Answers

Heater fan switch won.t work on 1,2,3 but only on 4 setting


this is a very simple problem, just replace the blower motor speed control resistor, it is in the air ducting right next to the blower motor.

Mar 13, 2009 | 2000 Jeep Cherokee

Not finding what you are looking for?
1998 Chevrolet S-10 Pickup Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...