Question about 1996 Chevrolet K1500

1 Answer

Lost reverse in 96 4x4 4l60-e trnsmission

4l60e tranny in 4x4 has no reverse. did not slip before going out. what happened? is there anything i can do at home to fix it, to avoid complete re-build?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 2,920 Answers

No theres nothing you can do at home to repair it you will need to send it to a shop to have it repaired

Posted on Feb 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transmission on my 99 suburban with no warning signs started slipping in all gears even reverse can a dirty filter cause this issue


if your transmission has been slipping, it means that the clutch plates and steel plates have gone. youre going to have to have it rebuilt or swapped out for a rebuilt one.

A transmission filter should never get dirty enough to prohibit the valve body and pump from getting enough fluid. unless you have driven the truck through deep water or heavy off road use.

The 99 suburban has a 4L60E or 4L80E transmission. depending on the chassis package, If you have a 1.5" rear yoke diameter(the thing connecting the trans to the driveshaft), its a 4L60E, if its larger you have the other. The trans are usually good for at least 150K miles under normal use.

Nov 10, 2013 | Cars & Trucks

1 Answer

1999 Blazer -4x4 4.3 liter 140,000 miles- lost reverse...no prior problems or symtoms...happened pretty much at once, Fluid ok...linkage appears to be ok....time for new tranny?


That year of blazer would have the electronic transmission in it, a 4L60E I believe? A pretty common problem I have seen with people who have the same kind of vehicle is the control module for the transmission and not so much the transmission itself, especially in 4x4's. Often times this problem occurs after going out wheeling, and it's often as simple as reconnecting the plug on the tranny, or pulling it off and cleaning off the contacts, or if that doesn't work then head to the junkyard and pull the module off of one from there (and hope that it didn't have the same problem)

Aug 20, 2010 | 1999 Chevrolet Blazer

1 Answer

My tahoe wont go in reverse is it the tranny? what kind of tranny is it. it has 4wheel drive


it is a 4l60e trans with a busted reverse shell..need to see your local trans shop for repairs...dealer would be best

Dec 19, 2009 | 1997 Chevrolet Tahoe

1 Answer

I have an 04 Silverado with the 4L60E. The


I would be interested to know why you kept pulling the tranny. Its possible you lost the prgram in the PCM. You may need a reflash. Where there codes. Or you may have a bad torque converter or trans oil pump.

Jul 15, 2009 | 2004 Chevrolet Silverado 2500HD

1 Answer

This is the 3rd tranny - Exact same thing is happening.


You might try to add a transmission cooler. If its getting hot it will eat the transmission easily. time to swap it out and sell the problem to someone else.

Jun 03, 2009 | 1996 Chevrolet Astro

1 Answer

4l60e slips in 3rd and 4th


There are to many things that can cause this problem, best thing to is go get the ECM scanned for DTC codes at a transmission shop or Auto zone or Parts Source since they scan for free.
The ECM should have DTC code in it's memory on how the transmission is Performing and have the Transmission line tested for Fluid pressure.
Good luck and hope this helps. Oh and also ways check with more then on transmission shop if there tell you that you need a new Transmission,
It could be a simple as the transmission filter falling off causing the lost of transmission fluid pressure. Check the transmission fluid too.

Apr 15, 2009 | 1996 Chevrolet Camaro

2 Answers

Replacing a 4L60E with a 700R4?


Not with good results, the 4L60E is run by your ecm, the 700R4 while looking close to the same does not relie on your ecm for commands,it relies on a cable to regulate your line pressure.

Jan 01, 2009 | 1994 Chevrolet K1500

1 Answer

4L60E slipping and not locking up


Very well could be taht the Computer is not recieving the Shift codes Correctly. Just for an Easy Solution, Remove the ECM Fuse from the Fuse panel for 2 or 3 Minutes to Reset the Computer and let me know what you get.

Dec 31, 2008 | 1994 Chevrolet K1500

Not finding what you are looking for?
1996 Chevrolet K1500 Logo

Related Topics:

373 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...