Question about 2002 Mercury Villager

1 Answer

2002 mercury villager, the fan will not work with the heat. used to only work on notch 4 but now not working at all. replaced the resistor but still doesnt work, trying to replace the blower motor itself but i can't get the last bolt undone closest to the firewall, any suggestions? taking glove box out maybe?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

Go to this site nad see photos posted by me.

Gerryhttp://autos.groups.yahoo.com/group/villagerquest/

Posted on Feb 11, 2009

6 Suggested Answers

  • 7 Answers

SOURCE: how to replace blower motor resistor on 2000 grand caravan

there will be two 8mm screws holdin it in.. with two connectors into it

Posted on Jan 05, 2009

chuck943
  • 783 Answers

SOURCE: Location of blower motor switch resistor on 2004 Grand Marquis

The blower speed controller is located under the hood on the right or passenger side on the heater housing just to the side of the heater hoses near the very back of the right cylinder head.
Yes that would cause the concern you are having.

Posted on Feb 05, 2009

c17hydro
  • 2984 Answers

SOURCE: does the blower motor resistor just pull out of

  1. Disconnect and isolate the negative battery cable.
  2. Disconnect the electrical connector from the front blower motor resistor.
  3. Carefully slide a screwdriver behind the driver’s side of the resistor to press in the locking tang and pry the resistor from the housing.

482a810.gif
To Install:
  1. Install the resistor in the housing with "TOP" at the top.
  2. Connect the electrical connector to the blower motor resistor.
  3. Reconnect the negative battery cable.

Posted on Jun 28, 2009

cj2176
  • 520 Answers

SOURCE: Where is the blower resistor on a 2001 Nissan Sentra?

Its actually not that bad to change. If you open the glove box and remove the screws then the screws along the bottom of the glove box at the bottom of the dash the box will slide out. Remember to disconnect the light if it has one. Now you will be able to see the underside of the dash. You can see a large black box that has wires and vacuum lines all over. You need to locate a small flat plate with two screws and a plug in the middle. Disconnect the plug and remove the screws. The resistor will come straight out. The back side will look like small coiled up springs of different sizes. Install in reverse.Hope this helps. Good luck. Please re-post with updates. Thanks cj2176.

Posted on Jul 13, 2009

  • 6982 Answers

SOURCE: Air Conditioner blower motor resistor was replaced

Motor is also energized by a relay. check that and also check that the motor itself is good by running a hot lead right to it. I'm sure you already checked the fuse and know the switch is good?

Posted on Jul 20, 2009

  • 181 Answers

SOURCE: Location of Front Blower Resistor on 99 Suburban K1500

MAIN BLOWER , MOTOR RESISTOR IS THE PLUG RIGHT BY THE BLOWER MOTOR. IF LAYING ON YOUR BACK LOOK UP AT BLOWER MOTOR IT THE PLUG TOWARDS THE FRONT SET ABOUT ONE INCH AWAY. PULL TWO 9/32 BOLTS OUT IT WILL PULL DOWN. THANKS

Posted on Feb 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The fan switch that works both heating and a/c only works on high or setting 4.


replace the blower motor resistor. its usually close to the blower motor.

Nov 19, 2010 | 2001 Mercury Villager

1 Answer

We have a 2002 villager, the fan only works on Hi setting, Checked the 20 Amp fuse in the panel to the left of the steering column, as well as the larger fuse in the engine compartment. Both are fine. Is...


The blower motor doesn't use a different fuse depending on the speed. The most common cause for your concern is bad blower motor resistors. The resistors lower the voltage to the blower motor so it doesn't turn at full speed when you have it set to fan speed 1. When the resistors blow out the only setting that works is full speed because it doesn't go through the resistor.

Sep 05, 2010 | 1999 Mercury Villager

1 Answer

A/C fan switch only works on high


it's your blower motor resistor in the plenum case. They usually blow the thermal limiter because the blower motor is drawing too much current. It's starting to go.
You can replace the resistor, 2 screws under the dash on the passenger side. It has a 4 or 5 wie connector. About $25 from a Ford or Mercury dealer.
Also go to the Villager site for more help.

http://groups.yahoo.com/group/villagerquest/

Jun 15, 2010 | 2001 Mercury Villager

2 Answers

Fan Blower only works on high. Resistor or ?


replace the fan speed control resistor.

Dec 23, 2009 | 2002 Mercury Villager

1 Answer

Location of blower fan resistor 02 mercury villager


if you have a manual control a/c system, it is in the heater plenum case held in with 2 screws. On the passengers side.

example

e439b31.gif
If you have electronic system, it does not have a resister. It has a blower motor speed controller.

Jul 14, 2009 | 2002 Mercury Villager

2 Answers

Electrical


If the fan only works on "high" fan speed then you need to buy what is called a blower motor resistor. You might be able to get one from your local parts store. I don't think that is a dealer item because of the age of the car. But if it is it shouldn't be very expensive. This I'm positive will solve the issue with the front fan. Don't have enough information about the rear . Hope this is helpful.

Apr 23, 2009 | 1996 Mercury Villager

Not finding what you are looking for?
2002 Mercury Villager Logo

Related Topics:

345 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...