Question about Cadillac STS

1 Answer

Over heating - STS Cadillac Cars & Trucks

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 404 Answers

Hi!
It appears we have an Air lock scenario and you will need to perform a system Bleed.
Park the vehicle on level ground, when cold remove coolant filler cap, start engine and leave to idle, turn heater on full and blower to max. When engine reaches operating temperature watch and listen near coolant filler, keep clear as gurgling and hopefully a boil over should occur. Top up with very warm coolant and wait as it may do it again.
Check for heat inside vehicle if warm replace coolant cap but keep an eye on temperature gauge as the ~Air lock may have moved on from heater matrix/core so proceedure needs to be carried out again from COLD.
If persistent boil ups/over attention must made in the cylinder head
or gasket area, or possibly water pump?
Please press the Blue button to appraise my FREE Efforts, Thank You!
Paul 'W' U.K.

Posted on Feb 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Trying to find which fuse is for the heated seats on a 2004 ford explorer sports trak


Heated Seats
This system allows the electrical heating of the front seats on passenger demand.
The components of the system are:
  • the seat heating elements located in the seat cushion and backrest.
  • the heated seat control switch, located on the seat side trim panel.
  • temperature sensors located in the seat cushion heating elements.
  • heated seat relay.
Do both front seat heaters not work ? Do you know how to test electrical circuits with voltmeter ?
PINPOINT TEST J: THE HEATED SEAT IS INOPERATIVE Test Step Result / Action to Take J1 CHECK HEATED SEAT SWITCH OPERATION
  • Key in ON position.
  • Press the heated seat switch on the driver and passenger seats.
  • Are both heated seat switch indicators illuminated?
Yes
If both indicators illuminate, Go To Pinpoint Test K . If only one indicator illuminates, GO to J5 .

No
GO to J2 . J2 CHECK THE HEATED SEAT RELAY CIRCUITS
  • Key in OFF position.
  • Disconnect: Heated Seat Relay C3250 (located under the driver seat).
  • Key in ON position.
  • Measure the voltage at heated seat relay C3250-86, circuit 1003 (GY/YE), harness side and ground; and between C3250-30, circuit 566 (DG), harness and ground.
    s5r~tr~en~file=a0078817.gif~gen~ref.gif
  • Are the voltages greater than 10 volts?
Yes
GO to J3 .

No
REPAIR inoperative 1003 (GY/YE) or 566 (DG) circuit. TEST the system for normal operation. J3 CHECK HEATED SEAT RELAY GROUND CIRCUIT
  • Key in OFF position.
  • Measure the resistance between heated seat relay C3250-85, circuit 57 (BK), harness side and ground.
    s5r~tr~en~file=a0078818.gif~gen~ref.gif
  • Is the resistance less than 5 ohms?
Yes
GO to J4 .

No
REPAIR circuit 57 (BK). TEST the system for normal operation. J4 CHECK THE HEATED SEAT RELAY
  • Install a fused jumper lead between heated seat relay 3250-30, circuit 566 (DG), harness side and heated seat relay C3250-87, circuit 1064 (YE/LB), harness side.
    s5r~tr~en~file=a0078819.gif~gen~ref.gif
  • Do both heated seat indicators illuminate when pressed?
Yes
INSTALL a new heated seat relay. TEST the system for normal operation.

No
REPAIR circuit 1064 (YE/LB) to switches. TEST the system for normal operation. J5 CHECK INOPERATIVE HEATED SEAT SWITCH INPUT
  • Key in OFF position.
  • Disconnect: Heated Seat Switch C320 (Driver) or C321 (Passenger) for the inoperative heated seat.
  • Key in ON position.
  • Measure the voltage between heated seat switch C320-2 (driver) or C321-2 (passenger), circuit 1064 (YE/LB), harness side and ground .
    s5r~tr~en~file=a0078820.gif~gen~ref.gif
  • Is the voltage greater than 10 volts?
Yes
GO to J6 .

No
REPAIR circuit 1064 (YE/LB). TEST system for normal operation. J6 CHECK CIRCUIT 57 (BK) FOR AN OPEN
  • Measure the resistance between heated seat switch C320-4 (driver) or C321-4 (passenger), circuit 57 (BK), harness side and ground.
    s5r~tr~en~file=a0078821.gif~gen~ref.gif
  • Is the resistance less than 5 ohms?
Yes
INSTALL a new heated seat switch. TEST the system for normal operation.

No
REPAIR circuit 57 (BK). TEST the system for normal operation It's not that simple , being a fuse . It's probably the relay or the heating element .
PINPOINT TEST K: SEAT DOES NOT HEAT BUT THE HEATED SEAT INDICATOR ILLUMINATES WHEN PRESSED ? Does it ?
Your best bet would be to take to a qualified repair shop .
Do

Jun 29, 2016 | 2004 Ford Explorer Sport Trac

1 Answer

Honeywell troubleshooting


Emergency heat is the setting that shows that your heat strips are activated. Sometimes people do not wire up the heat strips at all as the use a great deal more power than the normal heat pump uses. The problem is that a heat pump comes to a point where it is not efficient at about 28 degrees and this is where you need the heat strips or if you want to heat the house quickly which a heat pump will not do. Heat strips are located in the ductwork and act like a space heater. A H/A tech is probably needed to check this stuff out for you.

Nov 15, 2013 | Cars & Trucks

1 Answer

2003 kia sedona replaced rear heat pipes now no heat and over heating?


Something is blocking the way for the heat to reach the vents.
Reconnect the pipes

Nov 25, 2012 | 2003 Kia Sedona

2 Answers

Heater not working blows but no heat


Oh no! What do you do when your car heater not working? How do you figure out why there's no heat in car? What if you have no heater in car? Before you start trying to figure out how to fix car heater yourself, you should know a little about how your car's heating system operates. That will help you to figure out your car heater problem and why your heater isn't working properly or even at all! So, let's talk about how your heating system functions and then about some of the more obvious reasons that it you may be getting no heat from car heater. In order to heat up the inside of your car, the heating system uses some of the excess heat produced from your engine. Actually the engine produces so much heat that if you didn't have a way to release it (the heating/cooling system in your car) it could harm and even destroy the engine! That is why the heating/cooling system is set up to remove some of the heat and keep your car running smoothly.

Oct 05, 2012 | 1997 Lincoln Continental

1 Answer

The driver's side heated seat won't turn off on my 2003 Mecury Moutaineer. Also, how do I change my cabin filter?


Your vhicle build date is on a blue sticker on the driver door or door frame. If not there, check other doors.
The heated seat Module is under the seat. You can unplug the connector on it or the heated seat switch to shut it off. I supect the module is bad. get one used from car-parts.com. The cabin air filter is under the leaf screen at the base of the windshield. Remove wiper arms and leaf screen for access. Please rate, thanks. Principles of Operation - Heated Seats - Vehicles Built 03/2002 Onward
NOTE: Two heated seat modules are used, one for vehicles built up to 03/2002 and one for vehicles built 03/2002 onward. The modules are not interchangeable.
The driver and passenger heated seats share a common battery and ignition feed. A shared ground source supplies the heated seat control switches. When the heated seat control switch is pressed with the ignition switch in RUN or START, a momentary ground signal is sent to the heated seat module. The heated seat module then supplies power to the heating element circuit. The cushion element and seat backrest element are wired in series and powered by the same output. The heated seat module also will ground the separate indicator circuit at the dual automatic temperature control (DATC) module display panel to indicate an ON state. The heated seat module will remain on until the heated seat control switch is pressed and a momentary voltage signal is received, or until 10 minutes expire. If the ignition source is removed from the module, the heated seat module will enter an OFF state and will not return to ON until the switch is once again pressed with the ignition switch in RUN. The heated seat module is designed to heat the seat to 37.5?C (99.5?F) and maintain the temperature until time-out or switched off. This temperature is maintained by the heated seat module monitoring the temperature sensor located in the seat cushion element, and adjusting the current flow to the heating elements.
--------------------------------------------------------------------------------------------------------------------------------

May 22, 2011 | 2003 Mercury Mountaineer

2 Answers

Where is the bank 1 sensor 1 o2 sensor located in a 2006 hyundai sontata gls v6?


The bank has to do with which side of the engine. The 'Sensor 1' indicates that it is upstream of the catalytic converter.

Heated Oxygen Sensor Removal & Installation Heated Oxygen Sensor (Front) (2.4L) hyundai-04-24-5822.gif

Heated Oxygen Sensor (Rear) (2.4L) hyundai-04-24-5823.gif

Heated Oxygen Sensor (Bank 1/Sensor 1) (3.3L) kia-04-00-5213.gif

Heated Oxygen Sensor (Bank 1/Sensor 2) (3.3L) kia-04-00-5214.gif

Heated Oxygen Sensor (Bank 2/Sensor 1) (3.3L) kia-04-00-5215.gif

Heated Oxygen Sensor (Bank 2/Sensor 2) (3.3L) hyundai-04-33-5855.gif

prev.gif next.gif

Jan 13, 2011 | 2006 Hyundai Sonata

1 Answer

Heated leather seats will not heat up. Switch lights up and all fuses are okay. Is there a hiddedn relay I am not finding? Is there a quick way to determine if the problem is in the heating element under...


are you saying neither the heated seat cushion nor heated seated back on either seat works? But the light or lights does work?

Please rate as solved if this helps you. It took some time to dig all this stuff up. Please report progress.

Here's some info to start you off:

  • The heated seat is inoperative — seat does not heat but the heated seat switch illuminates when pressed
  • Circuitry.
  • Heated seat module.
  • Seat heater and temperature sensor.
  • Seat back heater.
  • Heated seat switch.


17ca9e8.gif
1d57fc6.gif

May 28, 2009 | 1999 Ford Expedition

1 Answer

2002 Grand Cherokee Heated Seats don't work


I will post it in 2 different posts because its too long DB

HEATED SEAT SYSTEM
Individually controlled driver and passenger side electrically heated front seats are available factoryinstalled optional equipment on this model, when it is also equipped with the power seat option. The heated seat system allows both the driver and the front seat passenger the option to select one of two seat heating ranges, Low or High, or to turn the individual seat heaters OFF using the heated seat switches located in the center lower bezel near the bottom of the instrument panel center stack. The heated seat switch circuit operates on ignition switched battery current supplied through a fuse in the junction block, only when the ignition switch is in the ON position.

The heated seat system consists of the following components
  • Heated seat elements
  • Heated seat sensors
  • Heated seat module (or memory heated seat module)
  • Heated seat switches.
The heated seat system also relies upon resources shared with other electronic modules in the vehicle over the Programmable Communications Interface (PCI) data bus network. The PCI data bus network allows the sharing of sensor information. This helps to reduce wire harness complexity, internal controller hardware, and component sensor current loads. At the same time, this system provides increased reliability enhanced diagnostics, and allows the addition of many new feature capabilities. For diagnosis of these electronic modules or of the PCI data bus network, the use of a DRB scan tool and the proper Diagnostic Procedures are recommended.

The electronic modules that may affect heated seat system operation are as follows:
  • Body Control Module (BCM) - Refer to Body Control Module in Electronic Control Modules for more information.
  • Heated Seat Module (HSM) - Refer to Heated Seat Module in Electronic Control Modules for more information.
  • Memory Heated Seat Module (MHSM) - If the vehicle is equipped with the Memory System, refer to Memory Seat Module in Electronic Control Modules for more information.
Refer to Power Seats Premium I/III in the Contents of Wiring Diagrams for complete circuit diagrams. Following are general descriptions of the major components in the heated seat system.

The heated seat system will only operate when the ignition switch is in the ON position, and the surface temperature at the front seat heating element sensors is below the designed temperature set points of the system. The heated seat system will not operate in ambient temperatures greater than about 41 °C (105 °F) . The front seat heating elements and sensors are hard wired to the Heated Seat Module (HSM) or the Memory Heated Seat Module (MHSM).

The heated seat switches are hard wired to the Body Control Module (BCM). The BCM monitors the heated seat switch inputs, then sends heated seat switch status messages to the HSM or MHSM over the Programmable Communications Interface (PCI) data bus. The HSM or MHSM contains the control logic for the heated seat system. The HSM or MHSM responds to the heated seat switch status messages, ignition switch status messages, and the front seat heating element sensor inputs by controlling the output to the front seat heating elements through integral solid-state relays.

When a seat heater is turned ON, the sensor located on the seat cushion electric heater element provides the HSM or MHSM with an input indicating the surface temperature of the seat cushion. If the surface temperature input is below the temperature set point for the selected Low or High heated seat switch position, the HSM or MHSM energizes the integral solid-state relay, which supplies battery current to the heating elements in the seat cushion and back. When the sensor input indicates the correct temperature set point has been achieved, the HSM or MHSM de-energizes the solid-state relay. The HSM or MHSM will continue to cycle the solid-state relay as needed to maintain the temperature set point.

The HSM or MHSM and the seat heater elements operate on non-switched battery current supplied through the power seat circuit breaker in the junction block. However, the HSM or MHSM will automatically turn OFF the heating elements if it detects an open or short in the sensor circuit, a short or open in the heating element circuit causing an excessive current draw, or when the ignition switch is turned to the OFF position.

See the owner's manual in the vehicle glove box for more information on the features, use and operation of the heated seat system.

I WILL POST THE REST

Jan 31, 2009 | 2002 Jeep Grand Cherokee

1 Answer

No heat


1 Inspect Cooling System Mix Coolant level low or flow is restricted. grey_line.gif 2 Inspect Thermostat Thermostat stuck closed grey_line.gif 3 Inspect Heater Control Valve Leaking or defective heater control valve.

Dec 04, 2008 | 2002 Pontiac Aztek

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...