Question about 1992 Buick LeSabre

1 Answer

1992 Buick LeSabre brakes bleed but very lil brake at pedle

All air is out no fliud loss any where but not much brake

Posted by on

  • iowa500 May 11, 2010

    think you mean not much brake pedal right

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 39 Answers

Start bleeding your brakes from the rear wheels and work your way to the front. I'm assuming you already did a pad change since you say you got the air out. make sure you keep the fluid level and not let it get too low while you're bleeding them or air will get into the master cylinder and you have to start all over again. Make sure you have someone help you that is competent enough to hold the brake pedal down all the way and not let off even the slightest bit until you get the bleeder screw tightened.

Posted on Feb 06, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Having a problem reinstalling Rear Brake Caliper


I am not sure what kind of vehicle we are talking about. not all rear calipers have a screw type piston. to take a stab in the dark at your problem as far as lining up the caliper when reinstalling the bolts get both bolts started before tightening. If your problem is fitting the new pads and caliper over the rotary it would be necessary to push the piston further back into the caliper. if it is a screw type or just requires you to push it back always push or screw it back all the way till it bottoms out after installation it will take a couple pumps of the brake pedal to set everything back to specs. FYI when pushing the caliper back I do not like clamping the hose or backing off the bleeder screw to me it leaves to much room for erorr. i prefer to pop the master cylinder cap off and then just lay it on there then begain to back the pistons up that way there is no fliud loss nor a chance for air to breach the system. good luck friend.

Apr 10, 2014 | Cars & Trucks

1 Answer

Hand brake light on dash intermittant. Switch at hand brake is ok


check the brake fluid level. the brake fluid can be low and comes on when stopping or going around curves. the brake fliud level sensor uses the same brake light as the parking brake. if the fliud is low check the pads and /or shoes for wear.

Aug 07, 2011 | Toyota RAV4 Cars & Trucks

2 Answers

I bleed brakes i get good brake for a day or two then they go out again what can i do


air must be entering the system somewhere, check all wheel cylnders for leaks, and check the master cylnder for leaks( some cars's master cylnders leak at the firewall and fluid runs down inside the car under the carpet)

Jul 12, 2011 | 1992 Buick LeSabre

1 Answer

How to adjust brake pedal in buick lesabre


Should not need to adjust the brake pedal.If it is low or going to floor check for leaks or air in brake lines.could also be that the rear brakes need adjusting.

Apr 14, 2011 | 1992 Buick LeSabre

1 Answer

The fluid is below at min, which the mechani says is good for a mazda 3. Is that right?


As you didn't explain which fluid is low, here's a general explaination. There's always a cause for any fliud being low, the only fliuds that can fall below minimun levels are brake fliud [ as the brake pads or shoes wear it takes more fluid to push the surfaces together ] if not checked on a routine service, such as oil changes. The other is windshield washer fliud, which is lost with use.
Any other fliud loss isn't normal, and should be addressed.

Mar 27, 2011 | Mazda MAZDA3 Cars & Trucks

1 Answer

How to properly bleed brakes on a 1992 buick regal gs


Loosen bleeder screw connect one brake bleeder tool from autozone and other shops similar. Keep posing it untill all bibles and air comes out of the brake line. Remember to refill while bleeding.

Dec 29, 2010 | 1992 Buick Regal

2 Answers

No brakes I think the booster was going out because my peddle got soft but would still stop me then i changed my brake pads shortly after the brakes completly went out and can now only stop with the...


The problem is not the booster, the job of the booster is to make braking easier. If the booster went out the brakes would be hard to press.
Your soft pedal is likely due to air in the brake lines. Bleed the brakes and go from there.

Dec 13, 2010 | 1992 Buick Park Avenue

1 Answer

Bleeding front brakes and brake pedal still goes to floor board


Must bleed all four brakes to determine if there is air in the lines.

If after bleeding several times, the brake pedal still goes to the floor board, the master cylinder may be determined to be bad.

Aug 12, 2010 | 2002 Buick LeSabre

Not finding what you are looking for?
1992 Buick LeSabre Logo

468 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...