Question about 1997 Ford Expedition

1 Answer

My 4 wheel drive went into 4 wheel high while my switch was in 2 wheel high and it wont go back. i checked the fuses and they are ok.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

There is a comfort control module under the dash that controls this function. mine got wet from a leak in the windshield (OE seal) it is on the drivers side. i replaced it and all is fine. (it had water stains inside it)

Posted on Feb 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Wont disengage out of 4 wheel drive 1998 ford ranger first time its stuck in 4 low we have backed up turned switch numerous times shut it off and restarted


Be sure to put the truck in neutral, while engine is running, while you disengage from 4 wheel drive (low) to 4 wheel drive (high) and then finally to 2 wheel drive. It is critical to shift transmission into neutral when switching out of 4WD Low, as indicated in your owner's manual. Hopefully, this will help to FixYa problem!

Oct 14, 2010 | 1998 Ford Ranger SuperCab

1 Answer

Won't shift out of 4 wheel drive low


modulator stuck or damaged located at transfer case take a rubber mallet and hit around where modulator and case connect than try to shift again if nothing than un bolt and lube and move actuator rod, with out try to move electronically w/switch back to 2 wheel drive -if moves should work can replace but look for replacement as back up if happens again just change over

Oct 05, 2009 | 2001 GMC Yukon XL

1 Answer

I put my 2000 escalade in 4 wheel low last night; and now I cannot get it switched back to 2 wheel high. I will not go above 50 miles an hour when I drive it. When I press the 2 wheel high button it...


start truck leave in park press 2 wheel high button put truck in drive move truck,check for being in 2 wheel high, if still in 4 wheel low have switch and shift solenoid checked

May 17, 2009 | 2007 Cadillac Escalade Two-Wheel Drive

1 Answer

1999 Chevy Suburban wont kick into four wheel drive


if it is electronic there is probably something wrong with the wiring..

but if it is manual...it might be the actuator........



Feb 11, 2009 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

1994 K1500 4 Wheel Drive Issue


No probably not, first check the fuse for the 4wd in the fuse box if that's OK its likely the actuator on the front axle..........providing the shifter handle moves to the proper location and if its push button the lights light in the switch when selected...the actuator plugs into the wiring harness and screws into the front differential.an easy remove and replace part even for a novice.

Dec 22, 2008 | 1999 Chevrolet Silverado 1500

3 Answers

Ford F150 front tires won't engage in 4 wheel drive


look on fire wall pass. side you will see 2 parts with vacume lines attached 99 percent of the time that is what went i had the same problem

Dec 15, 2008 | 1999 Ford F150 Regular Cab

1 Answer

93 ford explorer xlt


First check your 4 wheel drive switch to make sure it works, for on an off settings. (Use a volt-ohm meter for this. On should show continuity in the readings (if digital then it should show zeros in the dial) Off should show no continuity or 1.0 in the dial.

1. Check your fuses.
2, IF OK, then check your FUSE LINKS.
3. IF OK, then check your 4 Wheel Drive relay in the fuse box.
4. IF OK, then check continuity of the wires harness to the 4 wheel drive switch for DC voltage.

Jul 26, 2008 | 1994 Ford Explorer Limited

4 Answers

4 wheel drive wont swich back to 2 wheel drive


For a temporary fix so the car can drive, remove the fuse for the four wheel drive. it won't actuate the four wheel. The car is always in 2wheel drive. the fuse is located under the hood, the very right side of the of the fuse box, the third fuse up from the bottom. This can be checked in the owners manual. When I need four wheel dr I place the fuse back in. I haven't fixed the problem yet but can drive it 2wheel on the road. think it is the control module for the four wheel dr located under the dash board behind the glove box. Dealer part for $450, I would rather install and remove a 10cent fuse

Jun 19, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
1997 Ford Expedition Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70374 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...