Question about Nissan Pulsar

1 Answer

Need to change the clutch in my 1995 nissan pulsar 1.5l...is it difficult

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 104 Answers

No, piece 'o cake! Like some other Nissans, but smaller.

Posted on Feb 03, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you adjust the clutch on a 1999 Nissan pulsar ?


if its a hydraulic clutch no, so if you have a problem with engaging the trans you will need a clutch. first check clutch fluid level and for leaks in system.. if its cable you can adjust.

Jun 30, 2015 | Nissan Cars & Trucks

1 Answer

Does a 1992 nissan pulsar radiator fit in a 1995 nissan pulsar


look it up on ebay. after searching for the right make and model, click on "see compatible vehicles"

Dec 15, 2014 | Nissan Cars & Trucks

1 Answer

1988 nissan pulsar n13 keeps getting stuck in first gear


YOUR CLUTCH CABLE MAY NEED ADJUSTING,HERE'S A LINK ON IT,

Feb 12, 2014 | 1988 Nissan Pulsar

2 Answers

Have a Nissan Pulsar 1999 - 1.6L. Was running fine, stopped at an interesection, went splutter, splutter, stop. Plenty of fuel in tank. Have since changed the fuel filter, checked there is fuel being...


Okay Im confused it says a 1999 nissan pulsar 1.6 Then it says a 1995 licoln continental. HMMM HMM . Okay lets begin a nissan 1999 pulsar (by the way pulsar was stopped in 1989) 80 psi is more that enough feul pressure for either vehicle. Fuel filter is change food. There is spark okay. 5 short and 5 long alright 5long 5 short in nissan it means no problem system pass. 5 short 5 long in Ford means ECM internal failure. For the Ford the Harmonic balancer need to be look at there is a crank sensor but the crank sensor is dependant on the signal ring on the Harmonis balancer if you put you hand on it are you able to move it either way if you can then you found the problem and that can set off 5 long and 5 short. Now for the nissan, spark and fuel look on the air cleaner youll see a long black duct is it torn up or did it come apart if that came out it sputter and sputter then stall. and that will give a 5 short and 5 long.

Apr 22, 2011 | 1995 Lincoln Continental

1 Answer

My sons Nissan pulsar n14 clutch is slipping, how hard is this to adjust?


hi, that is an auto adjusting clutch. If it is slipping then either the adjusting mechanism is broken or your clutch is worn out and needs replaced.

Sep 19, 2010 | 1990 Nissan Pulsar

1 Answer

Nissan pulsar '88. replaced starter motor, then


Is it a manual, or an automatic? Earlier Nissans sometimes have a problem with the neutral safety switch (a device that keeps the engine from rolling over in gear or without the clutch depressed.) Generally, if their bad, they need to be a little warm before they'll start, like setting in the sunlight for a few hours.

Good Luck!

May 22, 2010 | 1988 Nissan Pulsar

1 Answer

Clutch cable just fixed and just started to stick to floor again


Check each end of the cable, there should be a clamp that holds the cable casing in place. If the
clamp became loose, when you step on the peddle
it would pull the cable and case not the clutch fork.
And the result would be, what you have now.
I hope this was of some help.

Jan 28, 2010 | 1990 Nissan Pulsar

1 Answer

1988 Nissan Pulsar will not engage clutch. Engine


You need to replace the clutch and pressure plate --your clutch is worn out. Plus other parts like throw-out bearing ,pilot bearing and may even need the flywheel machined flat.
You need to take it to a shop or if you are mechanicaly minded could do it your yourself,

Nov 15, 2009 | 1988 Nissan Pulsar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...