Question about 2005 Chevrolet Impala

1 Answer

Water pump replace

What do i have to do to get the bolt out from behind the power steering pulley on a 05 impala with a 3.8? i how there is a trick?? thanks

Posted by on

  • Ronnie Wilson May 11, 2010

    Is there a Hole In the Pulley ? Go through the Hole

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,596 Answers

Water Pump Replacement (3.8L)

Removal Procedure

  1. Drain the cooling system.
  2. Loosen the water pump pulley bolts.
  3. Remove the drive belt.
    1. Remove the water pump pulley bolts.
    2. Remove the water pump pulley.
    3. Remove the power steering pump and reposition.
    4. Remove the water pump bolts.
      1. Remove the water pump.
      2. Remove the water pump gasket.
      3. Clean and inspect the water pump mating surfaces.
      Installation Procedure
      1. Install the water pump gasket.
      2. Install the water pump.
        1. Notice: Refer to Fastener Notice in Service Precautions. Install the water pump bolts.
          • Tighten the long water pump bolts to 34 Nm (25 ft. lbs.) .
          • Tighten the short water pump bolts to 22 Nm (16 ft. lbs.) .
            1. Install the water pump pulley.
            2. Install the water pump pulley bolts.
              • Tighten the bolts to 13 Nm (115 inch lbs.) .
            1. Install the power steering pump.
            2. Install the drive belt.
            3. Fill the cooling system.
    5. The Whole Thing I Know You Didnt Want to hear that about The P/S Pump Thats why I Did More Reserch you seemed to Know what You are Doin They get the Best of us though Hope this Helps & RATE ME PLEASE

Posted on Feb 03, 2009

2 Suggested Answers

  • 32 Answers

SOURCE: Water Pump removal on 2001 Impala

yes

Posted on Mar 22, 2009

  • 416 Answers

SOURCE: 97 lesabre water pump 1 bolt left behind power

you have to remove p/s pump need to put socket in hole on p/s pulley to get to bolts to remove pump

Posted on Feb 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace Power steering pump 05 impala 3.8 Motor


if it is like the 02 impala its under the alternator which has to be removed the radiator tank resevoir, the inlet for the heater hoses which is on the front of the motor also has to be removed to get all psp bolts out power steering pump 2 to 3 hour job DYI

Dec 02, 2011 | 2005 Chevrolet Impala

1 Answer

How do i get to the bolt on waterpump behind a pulley on 2005 chevy impala ls with a 3.8 engine? Bolt is behind a power steering pulley......


It would probably be easiest to remove the whole power steering pump. Sometimes you have to work around things like that when workin on cars

Jul 13, 2011 | 2005 Chevrolet Impala

2 Answers

I almost have the water pump off but there is one bolt that is behind the power steerng pulley that I can not remove. I was wondering how to remove the power steering pulley?


To remove the pulley wheel from the power steering pump you typically have to remove 3 bolts but to get to those 3 bolts you have to use a socket and go through the holes on the pulley itself.

Apr 30, 2011 | 1995 Buick Park Avenue

1 Answer

Serptine belt diagram


q4073a.gif



Belt Installation, Aerostar 4.0L Engine


q1815e.gif


Item Part Number Description 1 8620 Drive Belt 2 N606068 Bolt 3 10300 Generator 4 10153 Generator Mounting Bracket 5 8509 Water Pump Pulley 6 6B209 Drive Belt Tensioner 7 N800199 Screw 8 8678 Belt Idler Pulley 9 N802096 Screw 10 19703 A/C Compressor 11 2882 A/C Compressor Mounting Bracket 12 3C718 Brace 13 N806020 Bolt 14 3A674 Power Steering Pump 15 3A733 Power Steering Pump Pulley 16 N800199 Screw 17 N606572 Bolt 18 N620481 Nut 19 8501 Water Pump 20 6312 Crankshaft Pulley A - Belt Tension Check (See Specifications) B - Tighten to 40-55 Nm
(30-41 Lb-Ft) C - Tighten to 24-30 Nm
(18-23 Lb-Ft) D - Tighten to 21-29 Nm
(15-21 Lb-Ft) E - Tighten to 40-50 Nm
(30-37 Lb-Ft)

Belt Installation, Ranger and Explorer 4.0L Engine


q4082b.gif


Item Part Number Description 1 8620 Drive Belt 2 10300 Generator 3 8678 Belt Idler Pulley 4 19703 A/C Compressor 5 3A733 Power Steering Pump Pulley 6 8501 Water Pump 7 6312 Crankshaft Pulley 8 6B209 Drive Belt Tensioner 9 N806020 Bolt 10 2882 A/C Compressor Mounting Bracket 11 3A674 Power Steering Pump 12 N606572-S2 Bolt 13 N800199-S8M Bolt 14 N620481-S2 Nut 15 3C718 Brace 16 N606068 Bolt 17 10153 Generator Mounting Bracket 18 8509 Water Pump Pulley 19 N605805-S2 Bolt A - Belt Tension Check (See Specifications) B - Tighten to 21-29 Nm
(15-21 Lb-Ft) C - Tighten to 40-55 Nm
(30-41 Lb-Ft)

Belt Installation, Ranger 2.3L Engine


q3646c.gif


Item Part Number Description 1 8678 Belt Idler Pulley 2 10300 Generator 3 8509 Water Pump Pulley 4 3A733 Power Steering Pump Pulley 5 2E884 A/C Clutch Pulley 6 6312 Crankshaft Pulley

Belt Installation, Aerostar 3.0L Engine


q4740a.gif


Item Part Number Description 1 10300 Generator 2 3F671 Belt Idler Pulley 3 3A733 Power Steering Pump Pulley 4 6B209 Drive Belt Tensioner 5 6312 Crankshaft Pulley 6 8509 Water Pump Pulley 7 19703 A/C Compressor 2010&c18=modelyear&c35=wsm%2cdrive%20belt%20replacement%2cssk%2c03-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 07, 2011 | 1995 Ford Aerostar

1 Answer

Removing power steering pump from v8 windsor


Section 11-02A: Steering Pump, Power, C-II 1996 Aerostar, Ranger and Explorer Vehicles Workshop Manual REMOVAL AND INSTALLATION Pump and Pulley SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Steering Pump Pulley Remover T69L-10300-B Steering Pump Pulley Replacer T65P-3A733-C
Removal
  1. Disconnect the power steering return hose (3A713) at the pump and drain fluid.
  1. Remove the power steering pressure hose (3A719) by unscrewing connector from the pump.
  1. On the Aerostar 3.0L V-6 engine (6007), loosen the drive belt tensioner (6B209) and adjustment bolts.





    Item Part Number Description 1 10346 Generator 2 8501 Water Pump 3 8678 Belt Idler Pulley 4 3A733 Power Steering Pump Pulley 5 6303 Crankshaft 6 2884 A/C Clutch 7 — Without A/C On the 2.3L I-4 and 4.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a counterclockwise direction. On Ranger 3.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a clockwise direction. Remove drive belt (8620) from under drive belt tensioner and slowly lower pulley to stop. Remove the drive belt from the power steering pump pulley (3A733).





    Item Part Number Description 1 10346 Generator 2 2884 A/C Clutch 3 3A733 Power Steering Pump Pulley 4 8501 Water Pump 5 6303 Crankshaft 6 8678 Belt Idler Pulley 7 6B209 Drive Belt Tensioner
  1. NOTE: If the drive belt requires servicing, refer to Section 03-05 .

    Remove the drive belt from the power steering pump pulley.
  1. Remove the oil dipstick tube.
  1. Remove the power steering pump support (3C511).
  1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley.
  1. NOTE: Do not apply pressure on the power steering pump rotor shaft (3B559). Pressure will damage internal thrust areas of the power steering pump (3A674).

    While holding the remover tool nut stationary with a wrench, rotate the inner spindle of the remover tool clockwise until the pulley is pulled off the power steering pump rotor shaft.
  1. Remove the bolts attaching the power steering pump to the A/C compressor mounting bracket (2882).
Installation
  1. Install the power steering pump on the A/C compressor mounting bracket. Install and tighten attaching bolts to 41-61 Nm (30-45 lb-ft). On 4.0L engine, tighten to 47-64 Nm (35-47 lb-ft).
  1. Position the support on the A/C compressor mounting bracket. Install mounting bolts and tighten to 47-64 Nm (35-47 lb-ft).
  1. NOTE: Fore/aft location of power steering pump pulley on power steering pump rotor shaft is critical. Incorrect belt alignment may cause drive belt squeal or chirp. Make sure pull-off groove on power steering pump pulley is facing front and flush with end of shaft ± 0.254mm (± 0.010 inch).

    Install the Steering Pump Pulley Replacer T65P-3A733-C and install the power steering pump pulley.
  1. Install the drive belt on the power steering pump pulley.
  1. On the 2.3L I-4, Ranger 3.0L V-6, and 4.0L V-6 engines, position and rotate drive belt on engine. While lifting drive belt tensioner in a counterclockwise direction (clockwise on Ranger 3.0L V-6), slide drive belt under drive belt tensioner and lower drive belt tensioner to drive belt.
    On Aerostar 3.0L V-6 engine, position the belt idler pulley (8678) assembly to give the drive belt the tension specified. Refer to belt tension check in Section 03-05 . Tighten the drive belt tensioner and adjustment bolts to 47-64 Nm (35-47 lb-ft).
  1. Install the power steering pump support, if removed.
  1. Install the oil dipstick tube.
  1. Install the pressure hose tube nut and new Teflon® wagner into power steering pump valve outlet fitting (3D654) and tighten to 41-54 Nm (30-40 lb-ft).
  1. Connect the power steering return hose to the power steering pump, and reposition the clamp.
  1. Fill the power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent fluid meeting specification ESW-M2C33-F. Start the engine and turn the steering wheel (3600) from left to right without hitting stops to remove air from the system.
  1. Check for leaks and recheck the fluid level. Add fluid if necessary to proper level as specified in Section 11-00 .


    Power Steering Pump and Power Steering Pulley, 2.3L TPH Engine, Ranger Only





    Item Part Number Description 1 2882 A/C Compressor Mounting Bracket 2 N606543-S2 Bolt (2 Req'd) 3 N606069-S2 Bolt (2 Req'd) 4 N605803-S2 Bolt 5 N800199-S8M Screw 6 3D673 Power Steering Pump Pulley 7 3F671 Power Steering Belt Idler Support 8 N806020-S2 Bolt 9 3A674 Power Steering Pump 10 19703 A/C Compressor A — Tighten to 21.2-29 Nm (16-21 Lb-Ft) B — Tighten to 40.3-55 Nm (30-41 Lb-Ft) C — Tighten to 44-51 Nm
    (32-38 Lb-Ft)

    Power Steering Pump and Power Steering Pulley, 3.0L Engine, Aerostar





    Item Part Number Description 1 3A674 Power Steering Pump 2 3C511 Power Steering Pump Support 3 6007 Engine 4 N803564 Stud 5 N802827-S2 Nut 6 N800199-S8M Screw (3 Req'd) 7 N8011179-S2 Screw (3 Req'd) 8

Jun 09, 2010 | 1996 Ford Explorer

1 Answer

97 lesabre water pump 1 bolt left behind power steering pulley is there a trick of the trade or remove pump?


you have to remove p/s pump need to put socket in hole on p/s pulley to get to bolts to remove pump

Feb 18, 2010 | 1997 Buick LeSabre

1 Answer

2000 monte carlo how to replace water pump.last bolt


there should be holes in power steering pump pulley that when positioned correctly the bole should go through one of those holes, if not then you have to remove the pump

Apr 29, 2009 | 2004 Chevrolet Monte Carlo

4 Answers

Camaro Water Pump!!!!


this happened to me about 2 months ago there are 3 or 4 bolts behind the power steering pump and under the coil packs. there are 11 bolts in all that hold your water pump on some are hard to get to so you are most like likly gunna have to jack it up.

Sep 22, 2008 | 1995 Chevrolet Camaro

Not finding what you are looking for?
2005 Chevrolet Impala Logo

1,567 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...