Question about 1992 Toyota Camry V6

1 Answer

Removing widow hand crank from passenger door

I need to replace the window crank on my 1992 Camry, but I can't seem to figure out how to remove the old one. I have removed all of the screws and fasteners, but there are none on the hand crank itself, and the crank won't just pop off. I don't want to damage anything by forcing it off either. Any suggestions?

Posted by on

  • Stacey Wallis Feb 03, 2009

    That was fast! Thank you so much, and I will give that a whirl.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

There is a Special Removal Tool that is available at any Auto Supply Store. Just tell them what you are trying to do and they will know what Tool that you need. There are a Few Different Kinds. Please Rate My Response! Thanks!

Posted on Feb 03, 2009

  • Travis Humphries
    Travis Humphries Feb 03, 2009

    No Problem! Happy to Help!



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do you remove the drivers side door panel on a 89 Camry. My manual crank window is out of the track and the door lock is broken. Also doyou just pull the window crankoff oris there ahidden screw.

The manual crank has a u shaped clip that holds it in place to the crank pulley. U may need a special tool to open the clip and slide it off so you can remove the handle.

Jan 16, 2017 | 1989 Toyota Camry

1 Answer

The exterior door handle on my 1993 Nissan pickup broke. I have a new handle but can't figure out how to remove the inside door panel to get to the area where I can remove the old handle and replace with...

Inside door handle should have some screws that need to be removed and the window crank will have a c-clip behind it . or some you have to pop the cover off the window crank

Oct 14, 2017 | 1993 Nissan Pickup

1 Answer

Remove drivers door

unbolt the outer door skin by removing the door handle fist there is a small pin in the bottom of the handle next to the lock when you have that out you will need to remove the t25 bolts that holds the skin to the fram

Sep 03, 2013 | 1992 Saturn SC

2 Answers

How to replace passenger side mirror on 2007 Camry

To remove mirror pry off inside triangle panel(black) which exposes 3 nuts which are removed with socket wrench. Detach wire harness and pull out mirror assembly. To replace insert new mirror screws thru assigned holes and reconnect wire harness and tighten nuts to snug. Push inside triangle panel back into place and you're done! It's that easy.

Dec 04, 2009 | 2007 Toyota Camry

1 Answer

The car alarm goes off and won't allow the car to crank. I had a window replaced in the drivers door and the automatic locks don't work what can I do. do i need a code to reset the alarm

whomever replaced the window removed the alarm harness. have the panel removed and check that the alarm harness is still attached to the back of the lock cylinder, Also you may try to unlock the car from the passenger side to disarm the alarm.

Oct 08, 2009 | 1992 Nissan Maxima

2 Answers

Replace outside door handle

Your going to have to remove the inside door panel to get to the two screws that hold the door handle in place. Just make sure your windows are up so the window is not in the way to get to the two screws to un bolt the out side door handle. You can buy the replacement door handle from Auto Zone and buy extra door clips, since they always break. Auto Zone will have the step by step instructions to get the job done and it should take just under an hour, some band aids will be handy too. Good luck and hope this helps, keep me posted, be glad to help.

Jun 22, 2009 | 2000 GMC New Sierra 1500

1 Answer

Need to install a passenger side mirror on my 1992 Honda Civic

Remove the door panel, one screw at the inside handle and one at the door pull hole, one plastic screw clip under mirror, use universal window crank removal tool to pop out a wire thin horse shoe shaped clip from the window crank if you loose it you can get another at the auto parts store for 50 cents. Gently pry off door panel, gentley pry off inside mirror cover from the top. Remove three screws to remove outside cover, Install mirror using 8mm head size nuts, reinstall.

Mar 12, 2009 | 1992 Honda Civic

1 Answer

Inside door panel removal

u need a window crank remover tool get at ny parts store

Feb 25, 2009 | 2001 Pontiac Sunfire

1 Answer

92 Toyota Camry V4

Sounds like the power lock actuator is going.On some cars it's part of the door latch and somethey are sep.. To remove door panel remove all the srews and pull out on panel. actuator is in lower corner of door. should be easy to find just use power locks and listen.

Sep 13, 2008 | 1992 Toyota Camry V6

Not finding what you are looking for?
1992 Toyota Camry V6 Logo

Related Topics:

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides