Question about 1995 Toyota Camry

1 Answer

Auto headlight feaature not working

After I turn off the engine, remove the key and then open the driver door, the headlight won't shut off if I leave it on. It should turn off immediately after opening the driver door.
One of the suggestion I found was to replace the headlamp relay. Is this correct? If so, how to remove the old relay,is it just unplug it? I tried to unplug it but it's kind hard to come off. Do I need more power to unplug it?
Thanks.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Before you go into any extensive electric workup, you should first check the trigger on the door to see if it is defective. It happens often in ice cold weather on old vehicles. It is a little black mushroom held by spring on the frame where the door has contact with. Wiggle it a few times to see if it turns the lights off.

Posted on Feb 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

How to disable auto-locking of your Toyota when you engage gear


As above, and works for all toyotas of a certain age, if it auto-locks when you put the car in gear, you can disable this if you wish - here's what to do:

Put the key in the ignition, turn it to the on position. Open the driver's door and remove the key (keep door open). Put the key in and out 4 times (in/ out only without any turning of the key) with the key taken out at the end. Hit the drivers side unlock button 5 times. Wait at least ten seconds and shut the driver's door. Away you go. If the car battery is ever disconnected it will reset this function, so you would have to repeat the above sequence once if this ever happens to disable the auto locking once again - or to put it back on, just disconnect the car battery for 10 minutes - remember to get the radio code before taking the battery off for any reason!

on Jan 17, 2010 | Toyota Camry Cars & Trucks

1 Answer

Alarm won't shut off on 1999 Chevy blazer 4x4


Is it factory alarm or aftermarket??. Try using the key to lock and unlock the doors driver and passenger then turn the ingnition on with the key and leave it in the key on engine off position for a few minutes and start the vehicle

Oct 14, 2012 | Cars & Trucks

1 Answer

What battery do i need for a 1999 323 key fob


It should be a CR2025 battery, u will also need to program the remote again.
REMOTE PROGRAMMING PROCEDURE:
Preparation
1. Close all doors, trunk, and hood.
2. The security system must be in disarm mode and key must be removed from the ignition key slot.

Enter Code learning mode
3. Open trunk and leave it opened.
4. Open the driver's door and sit in the driver's seat.
5. Close the driver's door.
6. Cycle ignition switch 5 times between Off and On (DO NOT START ENGINE, just quickly turn key to the position that illuminates all of the lights in the instrument cluster 5 times.)
The red status light will illuminate continuously, and the siren will chirp once to indicate that the code learning mode has been initiated.
The ignition switch cycling must be performed within 10 seconds.
The sequence in steps 1-6 must be performed within 45 seconds.

Register/Delete ID Code(s)
7. Open driver's door (remain seated in driver's seat.)
8. Close driver's door.
9. Press and release any button on the remote you wish to register into the system. The status led will shut off momentarily to indicate that one ID code has been registered.
10. Repeat steps 7 to 9 to register the remain the ID codes (remotes).

Exiting code learning mode
11. Open driver's door and exit vehicle, leaving the door open.
12. Close trunk.
13. Close driver’s door. The LED will turn off and the siren will chirp

Mar 15, 2010 | 1999 BMW 323 Series

3 Answers

2006 FORD FREESTAR VAN THE RADIO CONTINUE TO PLAY AFTER THE VAN IS TURNED OFF AND THE KEY IS REMOVED. ALSO THE CLOCK CONTINUES TO DISPLAY WITH THE KEY REMOVED


This is normal until you open a door. It will stay on for about twenty minutes as long as no doors are opened.

Mar 24, 2009 | 2006 Ford Freestar

2 Answers

The security on my 1993 Grand Cherokee will not turn off


I may be able to help if you havent fixed it yet. I believe I had the same/similiar issue...

I would make sure all of the doors were locked with auto lock button on inside of door, then I would shut the door so all doors were locked from pressing the inside auto lock button. then I would use my key to unlock the trunk, open the trunk and close it leaving it unlocked. then i would use the key to unlock the drivers door and the security would reset... if not then unhook the battery for a few minutes then hook back up and see if that works.. glgl

Mar 10, 2009 | 1993 Jeep Grand Cherokee

1 Answer

Program my remote


Program your factory keyless entry functions
For 2001+ Tacomas equipped with a factory alarm or keyless entrymag-glass_10x10.gif, here are some programming options that allow you to adjust the way your locks work.
The first programming option allows you to set the entry unlock to: (A) unlock the driver door with one push, and the remaining doors with a second push OR (B) unlock all of the doors with a single push.
  • Open the driver's door. Remove the key from the ignition switch.
  • (Complete these steps within 40 seconds)
    1. Insert the key into and remove it from the ignition switch 2 times.
      (IN - OUT - IN - OUT)
    2. Close, then open the driver's door 2 times.
      (SHUT - OPEN - SHUT - OPEN)
    3. Insert the key into and remove it from the ignition switch 1 time.
      (IN - OUT)
    4. Close, then open the driver's door 2 times.
      (SHUT - OPEN - SHUT - OPEN)
    5. Insert the key into the ignition switch and leave it in.
    6. Close the driver's door.
    7. Turn the key from LOCK to ON 4 times, ending at LOCK
      (LOCK - ON - LOCK - ON - LOCK - ON - LOCK - ON - LOCK)
    8. Wait for the locks to stop, then remove the key from the ignition switch.
  • On the key fob, press and release both LOCK and UNLOCK buttons at the same time.
    1. [For all doors unlock] press and release the UNLOCK button.
    2. [For driver door unlock] press and release the LOCK button.
  • Open the driver's door. The programming is complete. If programming did not occur, start over.

Jan 13, 2009 | 2001 Toyota Tacoma

1 Answer

97 camry headlights stay on


more than likely one of these is bad: 1. GAUGE Fuse (I/P J/B No.1)
2. Integration Relay (I/P J/B No.1)
3. Door Courtesy Switch (Driver’s)
4. Wire Harness

BE−14
BE−31

Nov 21, 2008 | 2006 Toyota Corolla

1 Answer

2005 Ford Expedition XLT, major electrical problems


You have a wiring harness problem
Take it to the dealer directly.......

Nov 18, 2008 | 2005 Ford Expedition

Not finding what you are looking for?
1995 Toyota Camry Logo

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...