Question about 1999 Saturn SC

1 Answer

How od i get the window crank handle off so i can replace speaker


Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

You can get the Tool for this at your Auto Parts Staore. There is a Special tool to remove and Reinstall the Clip for the Handle. Please Rate My Response! Thanks!

Posted on Feb 02, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

No sound from speakers in 2000 GMC Yukon? Whats going on?

1 Disconnect the trucks negative battery cable.
  • 2 Unhook the clip for the door's manual window crank with a hooked tool behind the handle (or rub a rag behind the handle), or for a power window, pry off the window switch assembly from the door handle with a trim stick and disconnect its electrical connector.
  • 3 Pry off all small panels and bezels on or near the door with the trim stick, including the triangular panel on the mirror mount and the bezel surrounding the door handle.
  • 4 Unscrew and remove all of the mounting screws for the door's inner trim panel then pull the panel out to detach the clips. Disconnect all remaining electrical connectors on the door panel.
  • 5 Peel off the plastic water deflector sheet from the door.
  • 6 Press down on the speaker's upper mounting tab while grasping the speaker, then tilt the speaker out of the door frame and lift it off the tabs on the bottom. Disconnect the speaker's electrical connector.
  • Connect the replacement speaker to the electrical connector.
  • 8 Secure the speaker to the lower tabs and pivot it into the mounting hole, clipping it in place with the door's mounting tab.
  • 9 Press the plastic shield back into place on the door.
  • 10 Reconnect the trim panel onto the door, connecting all needed electrical connectors and engaging all its clips, then apply its mounting screws. Reconnect all smaller panels and bezels to the panel.
  • 11 Reinstall the window crank or control switch with its clip or electrical connector.
  • 12 Reconnect the black battery cable onto the negative terminal.


  • Jun 01, 2012 | GMC Yukon XL Cars & Trucks

    1 Answer

    Need to remove driver side door panel?

    1. Disconnect the negative battery cable.
    2. If equipped with an accessory switch panel, carefully pry the switch panel up and away from the door panel. Tag and disconnect the switches from the panel.
    3. On 1981-86 models, remove armrest attaching screws.
    4. On 1987-96 models, remove the retainer screws secure the pocket in the molded armrest on the door panel.
    5. If equipped with crank type windows, remove window crank handle with the appropriate clip removal tool.
    6. If equipped with manual remote mirrors, remove the control knob bezel.
    7. Remove inside door handle cover attaching screw and trim plate.
    8. If equipped with door mounted speakers, remove the speaker, and disconnect the speaker wires. For speaker removal and installation steps, refer to .
    9. Remove all external screws securing the door panel. Insert an appropriate prytool between the door panel and door frame to remove the hidden clips securing the panel.
    10. Holding door panel vertical lift straight up to release the upper clip.
    11. Inspect all retaining clips and replace any broken or missing pieces.

    To install:
    1. Position the door to the door and carefully press on the retainer clips to engage. If a clip will not engage, inspect the mounting hole behind the panel to make sure the clip is properly aligned. Install any panel-to-door retainer screws.
    2. If equipped with crank windows, attach the washer and crank to the window regulator stud.
    3. On 1981-86 models, attach the armrest to the door using the retainer screws.
    4. On 1987-96 models, insert the armrest pocket and secure in place with retainer screws.
    5. If equipped with door panel mounted speakers, attach the speaker wires to the speaker and secure the assembly to the door panel.
    6. If equipped with remote cable mirrors, attach the control knob to the door panel with the retainer bezel.
    7. If equipped with an ashtray, insert the holder assembly, and secure in place with retainer screws. Install the ashtray to the holder assembly.
    8. Position the door handle trim panel around the door handle assembly, and secure in place with the retainer screw.
    9. If equipped with accessory switch panel, attach the harnesses to the switches, and press the accessory plate into the door panel.
    10. Connect the negative battery cable.
    11. Check and make sure all panel components function correctly.

    Apr 03, 2010 | 2002 Ford Explorer Sport Trac

    1 Answer

    Remove & replace window cranks---- Jeep patriot 2009

    you need to use a window crank removing tool and remove handle. Make sure window is all the way up before reinstalling handle on splines.

    Mar 05, 2010 | 2009 Jeep Patriot

    1 Answer

    How to remove 1991 subaru window handle knob

    There is a clip holding the handle in place. It is just behind the handle and not easy to see.
    This video should help, even if the vehicle is different (oh, and it is not a trick or hack as those are overused terms these days):
    Window Crank Removal Trick

    Jan 21, 2018 | 1991 Subaru Loyale

    1 Answer

    Broken plastic window crank handle on Geo Trakcer 1994

    get a toyota handle its plastic but its stronger, the metal handle is going to be hard to interchange, the best thing to do is remove your handle and go to a junk yard and see which handles are the same, you can even put your handle on and see if it works on that car, hope this helps.

    Feb 05, 2010 | 1996 Geo Tracker 2 Door

    1 Answer

    How to remove the inside door panel from a dodge 2005 2500 pick up

    Release door latch and open door.
    Roll window down.
    Remove window crank Window Crank - Typical , if equipped.
    Remove screws attaching trim panel to door Door Trim Panel and Trim Panel Screw
    CAUTION: Do not forcibly pull trim panel from door, damage to trim panel may occur.

    Simultaneously lift upward and outward to release retainer steps from inner door panel Trim Panel Retainer
    Disengage inside handle linkage rod from inside handle.
    Disconnect speaker harness wire connector Speaker And Power Mirror Connector
    Disengage power mirror wire connector, if equipped (driver's side only) Speaker And Power Mirror Connector
    Disengage clips attaching power window/lock switch panel to door trim panel. Disengage wire connector from switch panel, if equipped Power Door Lock/Window Connector
    Separate door trim panel from vehicle.
    Position trim panel at door.
    Engage wire connector for window/lock switch panel, if equipped. Engage clips attaching power window/lock switch panel to door trim panel.
    Engage power mirror wire connector, if equipped.
    Connect speaker harness wire connector.
    Engage inside handle linkage rod to inside handle.
    Align trim panel retainer steps with inner door panel and slide trim panel into place.
    Install screws attaching trim panel to door.
    Install window crank, if equipped.

    Hope helped with this; remember rated this help. Good luck.

    Nov 12, 2009 | 2005 Dodge Ram 2500 Truck

    1 Answer

    I need to take the window crank handle off of my door

    auto parts store h as special tool to remove clips but u can use a flathead scerw driver gently pull handle from door panel and sneak screw driver behind handle pushing c clip out but becarefull they sometimes shoot out

    Mar 26, 2009 | 1995 Dodge Neon

    1 Answer

    Window crank handle on a 97 dodge dakota

    Look for screws in door little pop outs then take backside of mirror off then pull out at the bottom of the door then around the sides lift up and out then take vapor barrier off then you can seeeverything else/ Please rate my response thank you very much

    Jan 22, 2009 | 2001 Dodge Dakota

    2 Answers

    How to get the window crank off on 2dr 06 cobalt

    there is a clip behind the handle. you should see something like a big plastic washer between handle and panel, the clip is between this washer and handle use a pick to get clip off

    Nov 25, 2008 | 2006 Chevrolet Cobalt

    1 Answer

    Removing the front door panel

    there a special tool to remove that clip or you can use a women nylon slip the nylon beetween the handle and door panel and move it be carefull that clip fly off when it loose thanks pierre

    Oct 08, 2008 | 1999 Chevrolet Malibu

    Not finding what you are looking for?
    1999 Saturn SC Logo

    Related Topics:

    49 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Saturn Experts


    Level 3 Expert

    79865 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8836 Answers

    Are you a Saturn Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides