Question about 2001 GMC Yukon Denali

1 Answer

Keyless Entry Code Box

Where can i find my Keless Entry Code Box in my 2001 Denali so i can Get the Keless Remote

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 56 Answers

On the ecu behind and below the dash

Posted on Feb 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remote keyless entry doesn't work


try looking for a fuse relay for the remote central locking in the fuse box

Oct 10, 2012 | 2001 Oldsmobile Alero

2 Answers

2001 ford explorer sport, door keypad reset


How to find the Security Keyless Keypad Code on the 1995-2001 Ford Explorer or Mountaineer and how to use the Keypad functions. The factory code is also printed on a label which is installed on the Remote Anti-theft Personality (RAP) Module. This is the module that controls the keyless entry system. It is located in the left rear quarter behind the removable panel (see photo). You will need to turn the two thumb screws counter clockwise and take the plastic panel off to be able to see the unit. A flashlight may be helpful in seeing the code. You are looking for the module and the 5 digit code on it like the one shown below.

1948e32.jpg


Now that you’ve got the code I’ll tell you how to use the Keyless entry and set-up your own code.Make sure when pressing the controls on the keyless entry keypad you press the middle of the buttons to ensure good contact with the controls.

4f796b1.jpg

Check this for Programing the Keypad.

Hope this help (remember rated this comment).

Mar 29, 2010 | 2001 Ford Explorer Sport

1 Answer

I need to know how to change auto door lock code on my mercury mountaineer


i dont know if this will help you but to change the auto lock codes on a 94 mercury sablethat is set into your remote keyless entry system at the factory.you can program your own personal code to unlock the vehicle. this code does not replace the prminant code that is programmed into your system.
to program your own code 1) select five digits for your personal code. 2) enter the code the dealership gave you. 3) within five seconds, press 1/2. 4) within five seconds of pressing 1/2, enter your personal code, pressing each digit within five seconds of the previous digit.
the keyless system registers this second code. to open your vehicle, you can now use either code. the module only remembers only one personal code at a time. entering a second personal code will erase the first personal code, replacing it withe new second one.
to erase your personal code 1. enter the original code. 2. press1/2 within five seconds of step 1. 3. wait six seconds
the keless entry system auto erased your personal code and will only respond to the permenent one. i hope this helps

Jul 24, 2009 | 1994 Mercury Sable

2 Answers

Sonata 06 keless programing


Hi,

I have heard of a site that would help you regarding programming your remote :-

http://keylessride.com/

Hope that i helped you.

Thanks for using "Fixya".

Jun 23, 2009 | 2006 Hyundai Sonata

2 Answers

Need the factory keyless entry code to reprogram drivers door keypad. Owners manual insert is no longer available.


Check inside the trunk lid for a label with a 5 digit code. If unsuccessful, then any dealer would be able to help you by checking the VIN number.

May 11, 2009 | 1998 Lincoln Continental

1 Answer

Key Pad Entry does not work


does the key pad light when you press a button at night? If yes, the fuse is ok.
Do you have the plastic card with the permanent code in your owner manual packet? If yes, tryit.
report back.

Keyless Entry The keyless entry keypad is hardwired to the GEM. The GEM interprets the inputs from the keyless entry keypad and then controls the associated operation. The keyless entry keypad will be illuminated for five seconds when any button is pressed. Additionally, it will request the illuminated entry feature to turn the courtesy lamps on. If a lock all doors code is entered, the illumination will turn off, as well as request the illuminated entry feature to turn off the courtesy lamps. When pressed, the keyless entry keypad supplies the ground signal to the GEM or the GEM receives a signal from the keyless entry remote transmitter. Then the GEM outputs a ground signal to the appropriate lock or unlock relay which supplies the power to the actuator to lock or unlocks all doors, including the luggage compartment. The keyless entry remote transmitter also unlocks the liftgate or activates the panic alarm by sending a signal to the GEM.
--------------------------------------------------------------- Visual Inspection Chart Mechanical Electrical
  • Keyless entry keypad
  • Keyless entry remote transmitter
  • Central junction box (CJB) Fuse F222 (20A)
  • Circuitry
  • Generic electronic module (GEM)
------------------------------------------------------------------------
  • No communication with generic electronic module (GEM)
  • Generic electronic module.
  • Circuitry.
  • REFER to Section 419-10 .
------------------------------------------------------------------------------------

Mar 08, 2009 | 2003 Ford Taurus

3 Answers

I can't find the keyless entry code for my 2004 ford freestar


The code is on the fuse box under the dash near the hood release. On my van there are two bar codes on a sticker attached to the fuse box. Under the first bar code, on the right side is the 5 digit code (bring your glasses the numbers are really small). After you get this code, just search the internet and there are plenty of forums on programing the keyless remote and also adding your own unique number to the key pad entry.

Good Luck

Mar 08, 2009 | 2004 Ford Freestar

3 Answers

Entry code om drivers door


The keyless entry module is located in the rear of the vehicle on the driver's side. You will need to partially remove the left rear panel in the cargo area. You will then see the keyless entry module bolted behind a metal reinforcement bar. There is a sticker on the module that has the 5 digit entry code.

May 26, 2008 | 2001 Mercury Mountaineer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

227 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...