Question about 1995 GMC Safari

1 Answer

Remove and replace motor

Where to cut upper radiator support to remove motor

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I have pics of a V8 swap in progress,engine installed via cut radiator support. send me an email at two-turbo@hotmail.com if you would like pics of it to see.

Posted on Mar 28, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Thermastat diagram install


Thermostat - 3.0L (2V) Removal and Installation
  1. Partially drain the engine cooling system. For additional information, refer to COOLING SYSTEM DRAINING, FILLING AND BLEEDING .
  2. Remove the three thermostat housing bolts. Fig. 25: Removing Thermostat Housing Bolts
    Courtesy of FORD MOTOR CO.

  3. Remove the thermostat O-ring seal.
  4. To install, reverse the removal procedure.
Thermostat - 3.0L (4V) Removal and Installation
  1. Raise and support vehicle. For additional information, refer to JACKING & HOISTING .
  2. Remove the front splash shield. For additional information, refer to FRONT END BODY PANELS .
  3. Drain the cooling system. For additional information, refer to COOLING SYSTEM DRAINING, FILLING AND BLEEDING .
  4. Remove the cooling tube bolt. Fig. 27: Removing Cooling Tube Bolt
    Courtesy of FORD MOTOR CO.

  5. Lower the vehicle.
  6. Remove the radiator upper cooling tube bolt. Fig. 28: Removing Radiator Upper Cooling Tube Bolt
    Courtesy of FORD MOTOR CO.

  7. Disconnect the upper radiator hose and engine vent hose. Fig. 29: Disconnecting Upper Radiator Hose And Engine Vent Hose
    Courtesy of FORD MOTOR CO.

  8. Remove the two bolts, and separate the radiator tube from the thermostat housing. Remove the thermostat. Fig. 30: Removing Bolts And Separating Radiator Tube From Thermostat Housing
    Courtesy of FORD MOTOR CO.

  9. To install, reverse the removal procedure.

Apr 22, 2012 | 2002 Ford Taurus

1 Answer

How do I replace the radiator hoses


I hope this is a routine maintenance replacement...Ask to see the radiator hoses at your local parts store...the exact replacement is best used for a perfect fit...in rare cases the replacement has to be slightly modified...(usually length) be sure the fit clears all fans...etc...there are 2 hoses involved, called the upper, and lower radiator hoses...the upper attaches to the water inlet on the motor...and the upper radiator connection...the lower connects to the water pump, and the radiator...when removing expect a major water spill...try to catch with a trash can lid under the front of your Acura...use new hose clamps in re-assembly. Hope this helps.

Feb 21, 2011 | 2000 Acura TL

1 Answer

How to change a radiator


1988–91 Models
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into a suitable container.
  3. Disconnect the fan motor and motor connector.
  4. Disconnect the upper and lower radiator hoses.
  5. Disconnect and plug the automatic transaxle cooling lines at the radiator, if equipped.
  6. Disconnect the coolant reservoir overflow hose.
  7. Remove the radiator attaching bolts and brackets.
  8. Remove the radiator with the cooling fan attached.
  9. Remove the cooling fan and shroud from the radiator. NOTE: Check all cooling system hoses for any signs of damage, leaks or deterioration and replace if necessary. To install:
  10. Attach the cooling fan and shroud to the radiator and install the assembly.
  11. Attach the radiator bolts and brackets. Tighten the radiator bracket bolts to 7 ft. lbs. (10 Nm).
  12. Connect the coolant reservoir overflow hose.
  13. Connect the automatic transaxle cooling lines to the radiator, if equipped.
  14. Connect the upper and lower radiator hoses.
  15. Connect the fan motor and thermo-switch wire connector.
  16. Refill the system with the proper type and quantity of coolant, check for leaks and bleed the cooling system.
  17. Reconnect the negative battery cable. Fig. 7: Cooling system components — 1988–91 engines 86833085.gif
1992–95 Models
  1. Disconnect the negative battery cable.
  2. Properly drain the cooling system into a suitable container.
  3. Disconnect the fan motor and motor connector.
  4. Disconnect the upper and lower radiator hoses.
  5. Disconnect and plug the automatic transaxle cooling lines at the radiator, if equipped.
  6. Disconnect the coolant reservoir overflow hose.
  7. Remove the radiator attaching bolts and brackets.
  8. Remove the radiator with the cooling fan attached.
  9. Remove the cooling fan and shroud from the radiator. NOTE: Check all cooling system hoses for any signs of damage, leaks or deterioration and replace if necessary. To install:
  10. Attach the cooling fan and shroud to the radiator and install the assembly.
  11. Attach the radiator bolts and brackets. Tighten the radiator bracket bolts to 7 ft. lbs. (10 Nm).
  12. Connect the coolant reservoir overflow hose.
  13. Connect the automatic transaxle cooling lines to the radiator, if equipped.
  14. Connect the upper and lower radiator hoses.
  15. Connect the fan motor and thermo-switch wire connector.
  16. Refill the system with the proper type and quantity of coolant, check for leaks and bleed the cooling system.
  17. Reconnect the negative battery cable. Fig. 8: Cooling system components — 1992–95 engines 86833086.gif
prev.gif next.gif

Aug 27, 2010 | 1991 Honda Civic

1 Answer

Need instructions on how to replace the cooling


Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Radiator upper crossmember
    • Fan motor electrical connector
  3. Drain cooling system below the level of the upper radiator hose.
  4. Remove or disconnect the following:
    • Upper radiator hose from radiator
    • Radiator fan fasteners and upper clip
    • Fan assembly by lifting upward to clear radiator
To Install:
  1. Install or connect the following:
    • Radiator fan assembly
    • Upper clip and fasteners
    • Upper radiator hose to radiator
    • Fan motor electrical connector
    • Radiator upper crossmember
  2. Fill cooling system.
prev.gif next.gif

Jul 17, 2010 | 2004 Dodge Intrepid

2 Answers

How do I replace a radiator on a 2002 maxima


Nissan Car 350Z & Maxima 1999-06 Radiator - Removal & Installation

  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Coolant reservoir tank and bracket Upper mounting bracket Upper radiator hose Oil cooler lines, if equipped Lower radiator hose Cooling fan and condenser fan Fan motors and shields Radiator

To install:
  1. Install or connect the following:
    Radiator Fan motors and shields Cooling and condenser fans and torque the bolts to 44 inch lbs. (5 Nm) Lower radiator hose Oil cooler lines, if equipped Upper radiator hose Upper mounting bracket Coolant reservoir tank and bracket and torque the bolt to 44 inch lbs. (5 Nm) Negative battery cable
  2. Fill the cooling system to the proper level.
  3. Start the vehicle, check for leaks and repair if necessary.
WARNING Do not remove radiator cap when engine is hot. Serious burns could occur from high-pressure engine coolant escaping from radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter of a turn to release built-up pressure. Carefully remove radiator cap by turning it all the way.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    Negative battery cable Coolant reservoir tank and bracket Upper mounting bracket Upper radiator hose Oil cooler lines, if equipped Lower radiator hose Cooling fan and condenser fan Fan motors and shields Radiator
To install:
  1. Install or connect the following:
    Radiator Fan motors and shields Cooling and condenser fans and torque the bolts to 44 inch lbs. (5 Nm) Lower radiator hose Oil cooler lines, if equipped Upper radiator hose Upper mounting bracket Coolant reservoir tank and bracket and torque the bolt to 44 inch lbs. (5 Nm) Negative battery cable

  2. Fill the cooling system to the proper level.
  3. Start the vehicle, check for leaks and repair if necessary.
WARNING Do not remove radiator cap when engine is hot. Serious burns could occur from high-pressure engine coolant escaping from radiator. Wrap a thick cloth around the cap. Slowly turn it a quarter of a turn to release built-up pressure. Carefully remove radiator cap by turning it all the way.
240ef5f.jpg

Fig. Exploded view of radiator and components
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    CAUTION Do not damage or scratch the A/C condenser and radiator core while removing.
    CAUTION Because A/C condenser is onto the front-lower portion of radiator, moving to rear direction should be at minimum.
    Negative battery cable Engine cover Air duct and air cleaner case assembly Bracket mounting bolt for anchoring A/C piping Reservoir tank and bracket Upper and lower radiator hoses Radiator cooling fan assembly On A/T models, A/T fluid cooler hoses. Plug hoses to avoid leakage Cover, then two A/C condensing mounting bolts located in the upper part of the radiator Rotate two radiator upper mount brackets 90 degrees in the direction shown in the illustration and remove fce8147.jpg

    Fig. Removing A/C condensing mounting bolts

    d3c8f50.jpg

    Fig. Rotating radiator upper mount brackets 90 degrees

    edb9f67.jpg

    Fig. Removing radiator
  4. Remove the radiator by performing the following:
    CAUTION Lifting A/C condenser should be minimum to prevent a load to A/C piping.
    With lifting and pulling radiator in a rear direction, disassemble lower mount from radiator core support center. Lift A/C condenser up and remove radiator after disengaging the fitting as front-bottom surface After removing radiator, put A/C condenser on radiator core support center to prevent a load to A/C piping, and temporarily fix it with rope or similar means

To install:
  1. To install, reverse removal procedure.
  2. Check radiator cap for any leaks.
  3. Start and warm up engine. Check for engine coolant leaks and A/T fluid leaks.

Hope this help (remember comment and rated this).

May 12, 2010 | 2002 Nissan Maxima

1 Answer

How do i remove radiator fan from my 2004 pt cruiser?


Hope this helps!

Removal & Installation
NOTE The fan motor, fan, and the shroud are serviced as an assembly.



CAUTION Do not open the radiator draincock with the system hot and under pressure, because serious burns from coolant can occur.


  1. Disconnect negative cable from battery.
  2. Remove battery and battery tray.
  3. Drain cooling system below upper radiator hose level.
  4. Remove grille.
  5. Remove upper radiator closure panel and center brace.
  6. Disconnect upper radiator hose from radiator.
  7. For turbocharger equipped vehicles: Remove radiator inlet neck.
  8. Hoist vehicle.
  9. Disconnect radiator fan electrical connector (.
  10. Remove the two lower and left side radiator fan screws and.
  11. Lower vehicle and remove the remaining radiator fan attaching screws.

    WARNING Care should be taken not to damage the radiator cooling fins and tubes during fan removal.

  12. Remove radiator fan by lifting up from the engine compartment.

c83d6ac.gif
Radiator fan mounting points

To install:
  1. Install the radiator fan into position on the radiator.
  2. Hand-start all radiator fan fasteners.
  3. Tighten all radiator fan retaining screws to 55 inch lbs. (6 Nm).
  4. Connect the radiator fan electrical connector.
  5. Carefully lower the vehicle.
  6. For turbocharger equipped vehicles: Inspect radiator inlet neck O-ring. Replace if necessary. Install radiator inlet neck. Torque fasteners to 55 inch lbs. (6 Nm).
  7. Connect the upper radiator hose to radiator. Align hose and position clamp so it will not interfere with the engine or the hood.
  8. Install upper radiator closure panel and center brace.
  9. Install grille.
  10. Install battery tray and battery.
  11. Connect cables to battery.
  12. Fill cooling system.

Apr 18, 2010 | 2004 Chrysler PT Cruiser

1 Answer

Want to replace the radiator on my 1997 ford thunderbird


Radiator Aluminum Core, Crossflow — 3.8L (Base) and 4.6L Engines
Removal
  1. Drain engine cooling system as described. Disconnect upper radiator hose (8260) and lower radiator hose (8286) and radiator overflow hose (8075) from the radiator (8005). Disconnect the transmission oil cooler inlet and outlet lines from the radiator.
  1. Remove cooling fan motor,fan blade (8600) and fan shroud (8146) assembly as described.
  1. Remove radiator upper bracket retaining bolts and remove bracket. Lift radiator from vehicle.
Installation
  1. Position the radiator into the vehicle. Install upper brackets and tighten bolts securely.
  1. Connect the transmission oil cooler lines to the transmission oil cooler fittings.
  1. Install cooling fan motor, fan blade and fan shroud assembly as described.
Engine Cooling Fan Motor, Fan Blade and Fan Shroud Assembly, Electrical Removal
  1. Disconnect (pull apart) the male-female cooling fan motor wiring connector at the side of the fan shroud (8146). Remove the male terminal connector retaining clip from the fan shroud mounting tab.
  1. Remove two fan shroud upper retaining bolts at the radiator tanks.
  1. Lift cooling fan motor/fan blade (8600)/fan shroud assembly past radiator (8005), disengaging fan shroud from two lower retaining clips.
Installation
  1. Follow removal procedure in reverse order.
  1. Tighten fan shroud retaining bolts to 5.2-7.2 Nm (46-63 lb-in).

  2. 10e2638.gif
    8d231fe.gif HOPE THIS HELPS.

    Oct 30, 2009 | 1997 Ford Thunderbird LX

    1 Answer

    I need to install an evaporator core in 1997 xj6. Any tips or suggestions?


    Ok , I will try to guide you as simple as I can :
    1- Remove the Heater / Cooler unit this is how : * Disconnect Battery ground cable
    * Recover AC gas or empty it in open space
    * Drain radiator coolant only
    * Remove instrument panel for access
    * From under the hood disconnect AC pipes at the evaporator , by removing bolts , discarding O-Rings and make sure to install blanking plugs so that no dirt goes in.
    * Disconnect heater hoses from heater matrix pipes , by releasing the spring band clips and make sure to blank the pipes
    * From inside the car , remove driver footwell duct , by removing the screw and then removing the duct
    * Remove upper steering column lower fixing , nuts and bolts
    * Remove upper steering column upper fixings (Bolts) , and allow column to rest down o the floor
    * Cut cable tie which secures console harness to LH blower duct
    * Remove LH fan motor duct (screws)
    * Remove passenger side footwell vent (nut)
    * Cut cable tie securing console harness to RH blower duct.
    * Remove RH fan motor duct (screws)
    * Disconnect Heater/Cooler Connector
    * Disconnect drain tubes from Heater/cooler assembly
    * Disconnect A/CCM connectors
    * Remove evaporator pipe support bracket fixing.
    * Remove Heater/Cooler assembly fixing , by removing lower nut and upper nut
    * Remove tape securing RH rear footwell intermediate duct joint. Remove duct to clear access
    * Remove tape securing LH rear footwell duct
    * Remove Heater/Cooler assembly from car.

    2- Remove AC control module 3- Remove evaporator pipe seal plate 4- Disconnect heater tempreture sensor 5- Remove footwell servo motor from heater/cooler unit * Disconnect connector
    * Remove screws
    * Remove motor complete with bracket
    6- Disconnect evaporator sensor connector * Detach heater/cooler connector
    * Detach evaporator sensor connector
    * disconnect connector
    7- By now you can see one upper and one lower case * Remove heater/coolent unit upper case from lower case
    * Remove screw
    * Remove 15 clips
    * Remove upper case from lower
    8- Remove evaporator from case * Remove sensor and clip

    You are done , make sure to replace all seals that you see to make sure that every thing is ok and you do not have any leaks after installation.
    Installation : Reverse order and after installing make sure to do a pressure test to make sure that there are no leaks

    Jul 12, 2009 | 1997 Jaguar XJ6

    1 Answer

    Replace radiator


    1. Disconnect the radiator fan motor connector. kcob130a.gif 2. Set the temperature control switch to the hot position. ecda063a.gif 3. Loosen the radiator drain plug to drain coolant. 4. Disconnect the upper and lower hose and overflow tube. 5. For vehicles with automatic transmission, disconnect the oil cooler hoses from the automatic transmission. Plug the ends of the oil cooler hoses and the automatic transmission fittings to prevent transmission fluid from spilling out and foreign material from entering. 6. Remove the radiator mounting bolts. 7. Remove the radiator and the fan motor together. 8. Remove the fan motor from the radiator. findme(''); findme(''); findme('');

    May 19, 2009 | 2001 Hyundai Elantra

    Not finding what you are looking for?
    1995 GMC Safari Logo

    Related Topics:

    77 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top GMC Experts

    yadayada
    yadayada

    Level 3 Expert

    61168 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you a GMC Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...