Question about 2001 GMC Yukon Denali

1 Answer

Keyless Or Alarm

I Need to Find Where in my Truck the Keyless System Or the Alarm System is located at I know its somewhere around the dash but Where?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

It is located under the dash passenger's side.

Posted on Mar 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I bought a ford pick up truck that came with a security alarm and a ungo remote control, I would like to know if this remote is keyless entry , so far I've been able to make it work only to turn the a


You can reset Your system by turning Your Key on and off several times and you should hear the doors lock and unlock.. you will need to this really fast/ On and Off and On and Off and On and Off . Then You should be able to set Your remote control numbers it will be a 4 digit code.. give it a try..

Dec 27, 2014 | Ford Cars & Trucks

1 Answer

Keyless entry does not unlock doors, open trunk, or start vehicle (remote start built onto keyless entry). Battery is new in BOTH remotes and neither one works. Could a fuse in vehicle be bad? Secondly,...


RFA / MOD fuse 10amp . location - insturment panel fuse box. Fuse Block - I/P
Right side of the I/P, behind the access panel
If the fuse is good your best bet would be to take it to a qualified repair shop , that doesn't mean the dealer . Lot of good independant repair shops around , just have to check the yellow pages.
Do you know what DTC'S are ? diagnostic trouble codes ! Not only the ones for the engine management system OBD 2 . There are also DTC'S for the remote keyless entry system , BCM - body control module. You need a factory or professional scan tool to view this codes
DTC B3101
DTC B3102
DTC B3103
DTC B3106

The remote control door lock receiver (RCDLR) communicates with the body control module (BCM) through the keyless entry serial data circuit. When any button on the keyless entry transmitter is pressed, the transmitter sends a signal to the RCDLR. The RCDLR sends a lock, unlock, or panic alarm request to the BCM, depending on which button is pressed on the transmitter. The BCM receives the message and performs the appropriate function. The BCM also uses the keyless entry serial data circuit in order to communicate with the RCDLR when programming transmitters. Do you know what serial data circuits are ?

DTC B3101 Keyless Entry Data Link Circuit Range/Performance
DTC B3102 Keyless Entry Data Link Circuit Low
DTC B3103 Keyless Entry Data Link Circuit High
DTC B3106 Keyless Entry Data Link Parity Error

This is what the factory manual said as to the location of power steering fluid reservoir ! Not much help , you would do better googling it.
The power steering fluid reservoir holds the power steering fluid and may be integral with the power steering pump or remotely located. The following locations are typical locations for the remote reservoir:
• Mounted to the front of the dash panel
• Mounted to the inner fender
• Mounted to a bracket on the engine

Aug 19, 2017 | 2005 Buick LaCrosse

1 Answer

Alarm will not go off


Answer
Gotcha, let's put it into valet/service mode,
and try to reset the alarm to default mode.

Look under the dash area for a button or, a toggle
switch. When you locate it, turn on the ignition
key, press and hold in the button (little
spring loaded micro button, red or black possibly)
until the alarm chirps 1 time. This should over ride
the system, and only the keyless entry part,
if installed, would still be operating.
The LED (light emiting diode) light in the dash
should also go on solid.

At this point. the alarm would have reset.
If this had a starter kill relay installed,
it would now be opened, and the engine would
turn over when tried.

You would repeat these steps to go back to
user mode to see if this was corrected.

Let me know if it works for yours.

ALARMTEK
INSTALLSUPPORT.COM

Nov 07, 2009 | 1995 Chevrolet Lumina

1 Answer

How to deactivate the car alarm on a Nissan pick up.


There should be a switch up under your dash board for this. Or a fuse for it as well

Aug 29, 2009 | 1997 Dodge Dakota

1 Answer

New battery -alarm sounds- have to disconnect the battery-


The sounding alarm maybe a security system installed by in the truck. Disconnecting the battery will only temporarily solve your problem, but will resume once you reconnect the battery for electrical power.

You must find the keychain/remote of the security system and disable it. If you are unable to locate this, you can have it disconnected by a qualified automotive electrician.

Word of caution though, if you are using the keyless entry system with the security system, this will be disabled until you install a receiver with such function.

Hope this helps.

Jun 29, 2009 | 1999 Nissan Pathfinder

1 Answer

Keyless and alarm stop working


I would have the keyless module replaced it,s located in the dash board . see manual.. if problem persists then The Alarm system has a electrical short and needs disconnecting or replacing...GL

Jun 26, 2009 | Saab 900 Cars & Trucks

1 Answer

Valet Switch/Button


Contact a dealer for the location of switch

May 02, 2017 | 2002 Mitsubishi Galant

1 Answer

Alarm system


locking and unlocking the drivers door with the key should deactivate the alarm

May 28, 2009 | 2000 Dodge Stratus

1 Answer

Connot manually turn off the alarm system


locate under dash fuse box. possibly on side of dash or in the glovebox. youll find an after market button. posh it.

Apr 25, 2009 | 1999 Toyota Tacoma PreRunner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...