Question about 1995 Nissan Maxima

1 Answer

Rear piston stuck in calipier

Maxiama qx

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 362 Answers

If you are talking about the rear disc brake caliper, then you need to replaced the caliper with a rebuilt unit.

Posted on Feb 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Left rear calipier


you mean the electric handv
brake?it is the small engine electrical on the caliper,
replace and re initiate by open close with computer,reset controle counter to 0
open and close by computer command,

Mar 24, 2014 | 2007 Volkswagen Passat Sedan

1 Answer

Front brakes shimmy or pulsate


Sound like warped rotors. Has the car been siting for while (eg at an airport ). Does the shimmy through the steering wheel or just the brake pedal? Make sure the pads are free in calipier, calipier slides are prone to sticking make sur there sliding ok. And pistons are going back ok hope this year helps

Aug 12, 2012 | 2000 Toyota Sienna

3 Answers

How do you get the caliber to move backwards so i can change rear brakes


REMOVE CALIPIER MOUNTING BOLTS ,THERE IS A CALIPER TOOL THAT TURNS THE CAPLIER PISTON IN FLUSH SO YOU CAN INSTALL NEW BRAKE PADS

Dec 19, 2010 | 2005 Pontiac Grand Prix

1 Answer

Smells like rubber burning


Check for brake problems stuck calipier or rear drum not releising see if there hot one more then the others but be careful not to get burned brakes that get stuck can get vary hot

Oct 30, 2010 | 1998 Jeep Cherokee

1 Answer

Changing rear brake pads. calipier wont aline bottom rod is out to far


you either havent recessed the caliper enough or you need to run your caliper through brake lathe some rotor that are new need to be turned in order to be true.there are slight variations even if new.or pads in backwards?

Nov 25, 2009 | 2005 Chevrolet Express

1 Answer

Rear brakes 05 merc montego


Try turning again clockwise with a little more pressure. If the brakes were worn badly the piston is just stuck from being adjusted out so far.

Jul 27, 2009 | 2005 Mercury Montego

1 Answer

Audi A6 Allroad


jack the car up saftely then take the wheels off .. then you will see the brake calipier turn the wheel towards you so the calipier is facing you . at the bottom of the calp you will see a small bolt at bottom undo this and lift prize the calp up then remove 1 pad the inside on where the piston is then put calp back down and put the bolt back in just to hold it in place then when you have done this put a large stronge screw driver in via hole in front to push the piston all the way back but make sure you do the evenly and piston goes in straight or it will get stuck same with all types of brakes. once you have done this reopen calp and take the other pad out clean all area with a wire brush and replace the new pads in place,, and retighten bolt etc , before you start the other side please make sure you pump brake peddle until it goes hard again. then do same to over side ,

hope this is a great help matdav69

Apr 07, 2009 | 2004 Audi allroad

1 Answer

BRAKES ON FRONT 2002 PROTEGE 5 MAZDA


When I change my front brakes, I use a "C" clamp to slowly push the piston back in. (You can get them for a few dollars at Wal-Mart, etc.) Make sure you open the brake fluid reservoir while compressing them, as the fluid level will rise; but don't leave the reservoir open too long, as brake fluid will absorb water from the air.
For the parking brake, I'm not sure. I think the parking brake often works off of the rear brakes, so changing the pads should have helped there. Maybe air in the lines? Do you have any trouble with "soft" or "mushy" brakes when you use them? If so, you might want to bleed the system, to get any air out - it can be dangerous.

Mar 21, 2009 | 2002 Mazda Protege

1 Answer

Rear brakes


The caliper is probably stuck, I had to replace one of mine, drivers rear. The piston on the caliper screws back in, so you'll need a caliper press to seat the piston.

Oct 25, 2008 | 2000 Lincoln LS

2 Answers

Rear brake pads


You need a spanner tool. You have to rotate the piston clockwise until it screws back into the calipier. DO NOT USE A C CLAMP as this will brake the calipier.

Aug 17, 2008 | 2004 Pontiac Grand Prix

Not finding what you are looking for?
1995 Nissan Maxima Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...