Question about 1994 Mitsubishi Galant

1 Answer

1994 mitsu galant CKP location?

I've got a 1994 Mitsubishi Galant S, it wont start so i took the OB1 codes and one was the crankshaft position sensor. The book i own isn't exactly user friendly being that its designed for pros... and i cant (some how...) find a diagram on the internet. Anybody have a diagram or just know where the location is?

Thanks,
Andrew

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 188 Answers

Why not go and purchase the sensor to see what it looks like. Then you know what you look for. It is usually close to the bottom pulley, usless it the cam chaft positioner?????

Posted on Feb 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I am trying to find the location for my crankshaft position sensor on my 1999 Mitsubishi Diamante


Your 1999 Mitsubishi Diamante is a 3.5L MFI SOHC 6cyl engine.
MFI = multi-port fuel injection
SOHC = single overhead camshaft
This answer covers Mitsubishi Diamante1.8L, 2.4L, 3.0L (SOHC and DOHC), 3.5L, and 1997-2000 1.5L Engines.

2.4L engine shown, others similar.

Fig.1 - CKP position and its two mounting bolts
am-trying-find-location-crankshaft-vkz3iz4htmqkl2kxsk34hqrj-3-0.jpg

In Fig. 1, the two arrows point to the CKP (crankshaft position sensor) mounting bolts to remove. 2.4L engine shown.

Fig.2 - CKP reluctor removal
am-trying-find-location-crankshaft-vkz3iz4htmqkl2kxsk34hqrj-3-2.jpg
Remove the sensor and slide the reluctor wheel off of the crankshaft-2.4L engine shown.

1. Disconnect the negative battery cable.
2. Remove the timing belt.
3. Unplug the sensor connector.
4. Unfasten the two retaining bolts, then remove the CKP sensor from the vehicle.
5. Installation is the reverse of the removal procedure.

Reference: Autozone online repair guide: Mitsubishi Galant/Mirage/Diamante 1990-2000, at
www.autozone.com

Fig.3 - photo - new 99Diamante CKP, a Wells part #SU4313
am-trying-find-location-crankshaft-vkz3iz4htmqkl2kxsk34hqrj-3-5.jpg

Jul 31, 2016 | 1999 Mitsubishi Diamante

1 Answer

Misubishi galant 2001 no spark wont start


Hi Tammy, does you vehicle have any lights lit on the Dash, check engine light etc... You need to see if you have battery + voltage at the coils , an to see if the PCM is turning them on an off ! PCM - is the engine control module . An see if there is an input signal from the crankshaft position sensor . It would also be good to hook-up a scan tool to see if it can communicate with the PCM . Mite have a shorted 5volt reference circuit . Do you have 2.4 L 4 cylinder or 3.0L V-6 ? IF you have the 2.4 L 4 cylinder you need to Check for B+ on the Black/White wire at pin 4 in the connector at the ignition failure sensor with the key on. Jumper the Black/White wire at pin 4 to the wire at pin 3 at the ignition failure sensor connector. If spark is present now, replace the ignition failure sensor. Unplug the Crankshaft Position (CKP) sensor connector. Check for 5 volts on the Green/Red wire. Reconnect the CKP sensor connector. Check the Black wire for a good ground. Check for B+ on the Red wire. If the Green/Red wire goes higher when connected to the sensor and cranking the engine, the CKP sensor is faulty. Let me know if you have questions, thanks.

Mar 08, 2015 | 2001 Mitsubishi Galant

1 Answer

Location of crankshaft position sensor on 2004 galant


Hey Kellop,here's a picture where it's at.Here's the sensor.

Feb 17, 2013 | 2004 Mitsubishi Galant LS

2 Answers

2001 mitsubishi galant crankshaft position sensor


the camshaft position sensor is located behind the harmonice balancer remove balancer and timing cover once removed you will see it u will also have to remove the crank gear and timing belt be sure to reset the timing or mark the gears before removal hope this helps

Jan 19, 2013 | 2001 Mitsubishi Galant

1 Answer

Mitsubishi 1994 galant idle suts off wont start back after % months at the technition


You need to check the fuel pressure and to run a fault code test on the electronic engine control system. Also check the cam belt. To run the test go here.

Oct 19, 2012 | 1992 Mitsubishi Galant

1 Answer

Install crank sensor on a 1999 mitsubishi galant need a diagram of the engine.


Hello! When you request help it is important to include the engine size...The 1995 Galant has two options; A 2.4L (4 cylinder) and a 3.0L (6 cylinder)...The Crankshaft Positioning sensor (CPS) requires removal of the timing belt...Purchasing a manual is a necessity...Guru...Saailer

Nov 01, 2011 | 1999 Mitsubishi Galant

1 Answer

2002 Mitsubishi Galant 2.4 with repeating error codes P0335,P0340


Check your timing marks , you may have jump the tooth on a timing belt.

May 10, 2010 | Mitsubishi Galant Cars & Trucks

1 Answer

Wont start sometimes after warm,code says cps


Its located on the right [ timing belt ] end or the engine,adjacent to the crankshaft timing belt sprocket.......

Jan 13, 2010 | 2001 Mitsubishi Galant

1 Answer

Why does 20a motor fuse blow? 1994 mitsu galant


I give up,,, why does a 20 amp fuse blow?seriously its probably an electrical short from the starter or alternator you may need an auto elec to diagnose the problem

Oct 25, 2009 | 1994 Mitsubishi Galant

Not finding what you are looking for?
1994 Mitsubishi Galant Logo

Related Topics:

327 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...