Question about 2001 Jeep Cherokee

1 Answer

Window off track

The little plastic piece conected to the cable on the auto, window. Wher does it fit inside the door frame

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

It either goes to regulator or door run channel or glass Please rate my response thank you very much

Posted on Feb 02, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Needinstruction on replacing window on 2000 jaquar s type

Windows do not come of any track

The window regulator that puts it up &
down has broken

Remove the inner door panel & you will
see the issue

Replace the broken assy,do not try &
piece it back together

Other than finding door removal instructions,
your on your own ,once inside the door

Try You Tube Video-- may get lucky & can
watch what you need to do yourself

Jan 24, 2013 | 2000 Jaguar S-Type

1 Answer

My driver side window on my 03 saab arc will not move. i took the door panel off and found there is a little plastic piece that slides up and down on the track that is broken. Now 2 cables, one from bottem...

you have to replace the whole window regulator it comes as a whole unit cable,slides (the broken plastic pieces)and may with or with out a motor. contact napa auto parts, a online saab parts supplier and ask for a window regulator assembly.

Apr 27, 2011 | Saab 9 3 Cars & Trucks

2 Answers

The passenger side window in my 2000 Lincoln LS has come off the track. How do fix that?

The window regualors on the lincoln LS are know pieces of junk.I have had several fail on mine.

The removal of the door panel is the trick I can help you with.
There are screws hidden under a plastic coner. This cover is at the bottom of the recess where the hand hold recess is on the door panel (the place where your fingers fit when you close the door). Pop the little cover up, and you will find the fasteners. The rest is more straight forward, once you get the panel pulled away, you can see whats going on inside your door.
It's not a fun repair, but paying the dealer is even less fun.

Good Luck

Nov 04, 2010 | 2000 Lincoln LS

2 Answers

Rear window wont go up. Motor works but seems to be binding

The window regulator, is cable driven, the regulator will have to be replace, when the cable goes bad, that's the sound you hear, you can more then likely move the window up and down a little.

Sep 13, 2010 | 2002 Mercury Mountaineer

1 Answer

Driver-side window fell off track. How to remove door panels and get window back on track?

1) remove the little plastic panel the covers the access to the outside mirror 2) remove the inside door opening handle 3) remove the window switches panel 4) disconnect all electrical contacts for #2 and #3, pull the upholstery panel, it has no screws, just self locking plugs, and careful with the door light, it has a very short cable. 5) remove the clear plastic protective sheet, very carefully, in order not to damage it, since it is attached with a reusable rubbery material. 6) determine what went wrong with the window glass guide.

Jun 28, 2010 | 1998 Honda Accord

1 Answer

How do you replace the window regulator and motor on the driver front side on 98 dodge grand caravan

Remove the two Phillips head screws that hold in the power master switch in the door. Gently pry it upward. Push the red clips aside on the plugs and squeeze the release on the plug and pull them off. Remove the screws from inside the door panel. Lift the panel up and away. Peel back the plastic to reveal the inner door. Duct tape the window over the upper frame a few times to keep in up. Peer inside the door for two metal clips that hold the regulator to the window and slide them out. Unbolt the front and rear vertical tracks that slide the window up and down. Take out the three torx head bolts that come through the door and hold the motor in place. Check tor plastic anchors (ribbed pointy things) that hold the cables (from making noise) going from the front and rear vertical tracks. Twist and wiggle the tracks and motor out the hole at the bottom rear of the door. It's a little stubborn to finagle out, but it'll come. Patience will overcome.

Mar 14, 2010 | 1998 Dodge Caravan

1 Answer

The drivers side rear window does not work. It does side down, and when the power switch is press the motor turns on. could the window be off its track or does the window unit need replaced?

It sounds like the window may be off its track. All that needs to be done is to remove the inner door panel. Be careful to pry the clips very gently. They break easily. However, most auto parts stores carry replacements. Once the door panel is off, remove the plastic sheeting that covers the door frame. It's attached with a mastic adhesive.
Once you have a clear view of the window rail, carefully pull the pane up and set the glass on the track. You may need to apply some silicone in the track to keep the glass in place.

Then, test the alignment by pressing the power button and roll the window up and down. With the window closed, replace the plastic sheeting and the door panel.

That should do it.

Oct 09, 2009 | 1994 Lincoln Town Car

1 Answer

How to install a rear window regulator on a 2000 Oldsmobile Intrigue

How do you remove door panels and replace window regulator on an Intrigue? Answer : For a 2002 Intrigue – Front Passenger I didn’t disconnect battery. You use window switch later to align window tabs to regulator frame – with ignition off power locks work, nothing is exposed.
1. Remove visible screw under armrest, pop out finger inset oval panel, remove exposed 2nd screw. 2. Pop off door handle trim – lock button assembly slide thru its hole in door panel. 3. Pop off window switch trim/holder – slide thru its hole in door panel. 4. Remove 2 slot screws under bottom of door.
5. I used a smooth metal letter opener (or old fork) to pry panel from door at each point plastic fasteners insert into metal. Start prying a little, see three on bottom perimeter two inches from edge. Three on door open edge and three on door hinge edge. Slow and easy = whole panel will pop off. A metal compression spring fastener connects at top door hinge edge trim – pry out. Be sure door lock and window switch remain inside. Clean all surfaces of door panel and lay on back seat.
6. With panel off you see clear plastic moisture sheet stuck to door with black rubbery paste - peel it from door for reattachment. You now see mechanism and fastener points. Lay out replacement window regulator and motor on mat by door to help you recognize fastening points, etc.
7. Carefully pull glass all way up and hold in place with two pieces duck tape two feet long with ¼# removal tabovers. Put a foot on outside glass and loop over door frame a foot to inside glass – with room to later redo when you twice lower and raise a foot to access bolts removing/attaching it to regulator bar.
8. Remove 3 bolts holding motor to door. 9. Remove upper 2 bolts and lower 2 bolts holding regulator frame to door.
10. Lower window to expose thru panel cutout area two bolts holding glass tabs to regulator, retape securely. Remove bolts, raise window, retape securely by looping over door frame.
11. Window regulator and motor assembly comes out as unit. Unplug window switch tab to release from motor. BEFORE reassembly clean the inside of the door, put in a little Borax for bugs, etc.
12. Reassemble by starting three motor bolts, fitting regulator assembly in door cavity. Replug window switch, motor can be placed in thru oval slots, leave all bolts loose. Replace two upper and two lower regulator bracket bolts, leave loose.
13. Turn on ignition, use window switch to lower window glass regulator tab bracket until accessible thru panel cutout. Turn off ignition, manually lower glass until tabs align with regulator bracket bolt holes and tighten these bolts. Take tape off, turn on ignition, raise window to top.
14. Tighten three motor bolts and four regulator bracket bolts, make sure alignment is OK. Remove your tape residue - clean goo from both glass sides with Goof Off. THEN raise and lower several times to assure all fits and works like new.
15. Reinstall clear plastic sheet, aligning any fastener holes and rubbing down perimeter with a cloth .
16. Align door panel, assure door lock and window switch are pulled thru. Visually align each tab on door opening side and pop them in one at a time. Continue on bottom – make sure you see them align or they will break. Finish on door hinge side and with metal fastener at top. IF you break a fastener, take one from small bag you bought from Pep boys - otherwise take bag back for refund…
17. Reinstall 2 armrest screws and 2 bottom panel screws, then pop in door lock, trim piece and window switch.
Clean the window inside and out with glass cleaner/polish/raineze so it will slide easily and your done. You can’t do anything about the motors going out. You can avoid regulator tab breaks by making sure the window is raised BEFORE closing those big doors – down is the weak moment!! I work slow and clean as I go, the job took two hours. I highly recommend – saved a bundle over dealer and they shipped everything in several days – as ordered!

Jul 27, 2009 | 2000 Oldsmobile Intrigue

1 Answer

Power window

there is a little plastic peace that rides on the inside track ,at the bottom of the window,its probably broke.Beware taking off the door panel is a pain,anyways,there is an arm that is attached to the motor ,with a ball on it & hard to see,you will have to constuct your own part because umm... you will not be able to find that part at a junkyard. So, look at the door itself and pop off one of the plastic pieces that you screw the door panel on with. Pop it out and drill a hole larger to fit the arm on the motor. The piece will slide into the bottom of the track of the window, it will fit like a glove

Aug 29, 2008 | 1989 Buick LeSabre

4 Answers

Door window on 2000 jaguar s type

take off inner door panel, lower track and put the window back in. If parts on track are broken buy new ones. Use urathain to reinstall window.

Jul 28, 2008 | 2000 Jaguar S-Type

Not finding what you are looking for?
2001 Jeep Cherokee Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

77939 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides