Question about 2000 Hyundai Elantra

2 Answers

Car misses while driving and idling and sometime dies while idlin

I have put my car on a machine 3 times, changed 3 sensors and it is still doing the same thing. It misses while driving it and when it is idling it misses even more and then eventually dies. It does this in gear and in park. Help!!!

Posted by on

  • frankie_fran Feb 02, 2009

    Solution helpful, will try it.

  • Anonymous Mar 20, 2014

    car miss at idling and driving speeds

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 4 Answers

Did u check spark plug, distributor cap and roter

Posted on Feb 02, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

If your car is Missing while Driving and or Idling. First have the Spark Plugs changed if this does not work also change the Rubber Wires over the Spark Plugs. The car would misses worse when the AC was on and the engine power was drastically reduced.
Every car need a Tune Up every once in a while check your users manual.

Posted on Sep 17, 2012

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, i hope that i can get some help from anyone in this forum, i havin problems whit my Dodge Dakota 2004 6cil 3.7 lts, the thing is that i have a misfire at idle and the p0300 code comes on, the truck...


You did everything I will suggest in normal case.only one step you miss!
Remove the crank sensor and stick 4 layer of masking tape,turn the engine to point were the ring is full(no hole)and install the sensor again.Use scan tool and learn the new position of the sensor.when the sensor move the timing move to ,if your flex plate is lose or damage will give the wrong angle for cyl.#1 After computer register misfire wil go to fail safe mode and set the timing to 10 degree
good luck

Oct 11, 2014 | Cars & Trucks

1 Answer

I changed sparkplugs, and wires1yr ago,aprox.8000 mi. now i'm having a miss, it then showed a code po303 and po316 so i changed fuel filter ,pulled out the irridium sparkplugs i put last and put in new...


You either have a bad ignition module or a
vacuum leak,intake manifold,PCV Hose,etc
that effects cyl #3

Ohm Checking is for the 1980's

Todays tool is an oscilloscope, you won't
have at home.

Also Smoke the intake and EVAP System
for leaks (EVAP Smoke Machine)

Mar 26, 2011 | Ford Taurus Cars & Trucks

1 Answer

1999 DURANGO IDLES BAD, CHECK ENGINE LIGHT ON, DIAG SAYS OPEN CIR


check to see if the cat is clogged if it is this will cause this to happen.

May 20, 2010 | 1999 Dodge Durango

2 Answers

92 Ford F150 4.9L. starts good, idles rough, dies at slow speeds


4.9 litre ?? you having a laugh its a 10ton truck engine not a pick up -global warming machine,remove the pump/sender unit and check the gauze filter also look inside tank for a something floating around ,i think the idles is not a related problem to the vehicle losing power but their is a possibility you could have a problem with the little vac operated thing on the fuel injector line that allows the fuel through only when the engine is running

Mar 15, 2010 | Ford F-150 Cars & Trucks

3 Answers

Truck idles fine all the time. However, on the


did you change the wires?..and cap?...could also be a bad coil

Mar 09, 2010 | 1996 Chevrolet K1500

1 Answer

Truck has a miss at idle and all rpms


I believe you have two separate codes; 24 and 31. 24 is "open or short in intake air temp sensor circuit" and 31 is "open or short in airflow sensor circuit at idle". These sensors may share a common ground so I would check that as well. You could also try putting a stethascope or (long screwdriver with your ear at the other end) to each injector and see if all are clicking like they should.

Feb 28, 2009 | 1994 Toyota Pickup

3 Answers

Car reving up and down on its own 3 to 4 times, then sputtering and dying?


The previous solution to check the idle air contol is in the correct area but needs some clarification.
The idle control is accomplished by two parts: Throttle position sensor ( $35 at Autozone) and idle contol valve approx $190. I replaced the throttle position sensor about a week ago and it runs perfect
to date but am a skeptic after almost two years of dealer incompetance. I researched all the sensors and failure symptoms on the internet and the throttle position sensor failure symptoms matched mine
exactly. See http://wiki.seloc.org/a/Throttle _Position_Sensor

Oct 03, 2008 | 2004 Hyundai Elantra

2 Answers

!985 Buick Century >


Do a balance test on the injectors. Remove one injector plug one at a time. Each time you remove one you should have a miss. All 6 should have the same miss. You could have an injector going bad.

Jun 29, 2008 | 1985 Buick Century

Not finding what you are looking for?
2000 Hyundai Elantra Logo

Related Topics:

1,098 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...