Question about 1988 Jeep Cherokee

1 Answer

Jeep 1988 want start new module pick up disp.no fire

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,201 Answers

Check coil for spark if you haven't already.

Posted on Feb 02, 2009


Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1988 Jeep Wrangler starting problems. I replaced the ignition module, spark plug wires, coil, distributor module, and my jeep will not start. It gets fuel, turns over, but still not starting. It is a 1988...


you are saying it is getting spark, and fuel, right? If it is getting spark, and fuel in to the throttle body, check compression-make sure the Mass Air Flow sensor is plugged in, and double check your spark-you say you replaced all those ignition items, but do not say that you have spark.

Jul 01, 2011 | 1988 Jeep Wrangler

1 Answer

My 1988 Jeep Cherokee 4.0L died on me coming home from work. I have no spark at the spark plugs. I have replaced the coil/control module assembly with a used unit as well as the camshaft position...


I am experincing the same problems with my 1988 jeep Cherokee 4.0. It died coming home one day,I replaced the motor and it turns over but gets no fire. I have repaced the control module, and distributor brand new my coil is testing good. I am wondering if it is my ECU also. The plug coming off distributor has one wire showing bright on test light, and one showing a dim light on test light and was wondering if you have checked these wires? Trying to figure out what will make these both shine bright.

Nov 09, 2010 | 1988 Jeep Cherokee

1 Answer

Getting spark and fuel and did a tune up and put new injectors in there but the car cranks but wont start and it is 1988 corvette


The ignition module and the pick-up coil/stator located inside of the distributor is what generates the signal that the ECM (Engine Control Module) uses to time and fire the fuel injectors, as well as the signal to run the fuel pump and the dwell signal timing to fire the ignition coil, and a faulty ignition module can cause any one of these systems to malfunction.

That does sound like a malfunction with the ignition module inside of the distributor, and you can remove the ignition module and have it tested for free at most auto part stores.

If you do purchase a new ignition module be sure that it does come with a silicone grease or a die-electric compound because it is a heat sink and the ignition module will burn up without it.

To install the new ignition module first clean out the mounting surface inside of the distributor. Then completely coat the metal contact surface under the ignition module with a thick coat the silicone grease or die-electric compound and do not leave any of the metal contact surface of the ignition module un-coated with the silicone grease or die-electric compound, and be very careful not to over-tighten the ignition module or it will be damaged.

The same principal applies to HEI (High Energy Ignition) ignition systems with the ignition coil mounted in the top of the distributor cap.

Sep 25, 2010 | 1988 Chevrolet Corvette

1 Answer

Need firing order diagram for 1988 Jeep 2.5 L


Forc 1988 Jeep Cherokee 4WD 2.5 liter L4 VIN "H" check...

361129b.gif


Hope help with this (remember rated this help).

Mar 05, 2010 | 1988 Jeep Cherokee

1 Answer

Got a 88 gt that fires but soon as it starts it goes dead!


You said pick up module,witch one did you replace,the pick up coil,or the ignition module,cause it sounds like the ignition module is the problem.

Feb 09, 2010 | 1988 Ford Mustang

1 Answer

1988 Chevy S10 Durango Pickup, Won't start will fire


sounds like ignition module inside of distributor cap under distributor rotor button.these do go bad and can easily be replaced.strong suspicion from your details that this is the culprit.

May 09, 2009 | 1988 Chevrolet S-10

1 Answer

Truck has no fire


try a new disributer i replaced it twice before i got a good one a mechanic said that ford distributers pick up coils had problems sometimes he would replace it 3 times before he got a good one

Mar 25, 2009 | 1988 Ford Bronco II

1 Answer

1988 jeep will not start put new module and pick up in the distributor no fire 6 cyl jeep wrangler please help


if its equiped with a crank sensor i would chk. that, if crank sensor bad you won't get no spark either.

Feb 02, 2009 | 1988 Jeep Wrangler

1 Answer

1988 jeep wrangle


Check your spark plugs. Without good spark plugs the ignition won't ignite. Just go look for Jeep spark plugs at like AutoZone and they are real cheap. To change them you will need a long socket wrench to twist them out and change each one.

Jan 30, 2009 | 1988 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...