Question about Chevrolet Blazer

1 Answer

Brakes not engaging

Brake pedal goes to the floor and front an back brakes dont work.changed front pads recently,also changed front passenger hub and caliper. please help

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 379 Answers

Sounds like there is getting no brake fulid to the line check the brake line open the top part of the brake line and see if fluid comes and if it does then good then open the side from the wheel and if it doesnt then ist clogged and u need a new brake lin e

Posted on Feb 03, 2013

  • jennifer graniczny Feb 03, 2013

    Bled front brakes got air out and front brakes there was fluid getting to the front. front brakes worked temporarily then nothing my husband noticed when he hit my parked Yukon. Emergency brake doesn't work either had to put n park to force it 2 stop! Please help!

  • Layne Johnson
    Layne Johnson Feb 05, 2013

    well if thats the case it sounds like its your master cylinder after awhile they get old and just dont work enymore so go buy a new master cylinder and then bleed ur brakes and that should fix it

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: Brakes no longer work in 1989 Chevy half ton pickup 2 wheel drive 350cubic inch

change dump valve under master cylinder

Posted on Aug 17, 2008

  • 139 Answers

SOURCE: bleeding brakes

always bleed front driver side first, front right,left back
right back.
make sure you always have oil in the master

Posted on Apr 09, 2009

  • 4 Answers

SOURCE: parking brake pedal goes to floor

The disc brake pads are NOT used for the parking brake. The parking brake uses mini-drum type shoes inside the rear disc rotor.

Take a look at http://wiki.answers.com/Q/How_do_you_change_the_emergency_brake_pads_on_a_2000_Chevy_1500_Silverado_Pickup

For more info

Posted on Jun 21, 2009

emissionwiz
  • 85108 Answers

SOURCE: brake pedal dropping to floor

do u have the antilock brake bleeding tool? if not you will need to have the dealer bleed the brakes, the ABS control valve must be electricaly held open to bleed the brakes there of course is a special tool for this.

Posted on Oct 18, 2009

Testimonial: "Thank You"

  • 1 Answer

SOURCE: Brakes are still spongy after changing the pads, one caliper, and master cylinder. bled front brakes.

I just went to Brake Masters this morning and had them replace the Master Cylinder since I was experiencing the pedal very spongy and going to the floor. When they replaced the Master Cylinder and they gave me back the car, the brakes were still spongy and going to the floor. I addressed this to them and they took another look at it, but when I took it for a second time, the brakes were extremely spongy. It was almost like they gave me back my car in worst condition to when I brought it in. Can you help?

Posted on Jul 31, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a low brake pedal on 2003 toyota 4runner


Did you also change the brake pads? Add fluid to top of reservoir?

Was the brake pedal low before you changed the calipers or is this something that developed after you worked on the car? If it was there before the caliper change then it has nada to do with the work you did.

U might have a bad master cylinder.

Nov 12, 2015 | 2003 Toyota 4Runner

1 Answer

Leaking brake fluid from right front wheel 1995 honda passport


Sounds like from what you describe it's a leaking break caliper. The best thing to do is get a rebuilt one. It's best to replace them in pairs. Also replace or clean the brake pads thoroughly!

Dec 20, 2012 | 1995 Honda Passport

2 Answers

I have replaced front rotors and pads even caliper on passenger side and rear brake pads but pedal still goes to floor


Did you bleed the brakes after doing all that stuff? You have to bleed em any time you remove the calipers

Jun 29, 2011 | 1999 Ford Explorer

1 Answer

How to change front brake pads on a mitsubishi triton 2003


You need to remove the front wheels do only one side at a time so if you forget where somthing goes you can look at the other side to figure it out . you then need to remove the brake caliper and push the caliper piston back to it fully reset postion using a c-clamp or a caliper piston tool .with the caliper off you need to clean the slides where the brake pads slide to make sure the new pads dont bind up . use a brake lube on these point after cleaning ( ask your parts store for this lube it will come in a little tube.Then install your new pads and reinstall the brake caliper , repeat this procedure on the other side. If you have never watched someone do this before and or you are not use to working on cars i would recomend not doing this your self this is a saftey issue . after installing both side of new brake pads reinstall you front wheels ,then sit in the drivers seat pump your brake pedal untill it feels full again ( not going to the floor) then start the car step on the brake and hold firmly. if the brake light does not come on you have completed your brake job correctly. If the light does come on have it towed to your repair shop don't drive it.

May 08, 2011 | Mitsubishi Pickup Cars & Trucks

2 Answers

Brake pedal goes to the floor


possible leak in brake system. if not then you have a bad master cylinder. have to replace it.

Aug 30, 2010 | GMC K2500 Cars & Trucks

1 Answer

After changing the brake pads my brake pedal goes to the floor. I tried to pump the brake, but it did not seem to work. When I changed the pads I took the bolt out of the brake line to the caliper to...


you need to check the fluid level is correct and that you have tightend the bolts to the caliper ,you have an air lock in the system by the sound of things you need to find the bleed screw on all four brakes and undo each one starting with the one furthest away from the brake master cylinder so start with passenger rear an so on have some one pump the brake on each screw you undo and tighten once you have the fluid coming through on each one you should then get your pedal back

Dec 23, 2009 | 2002 Honda Odyssey

2 Answers

How do I bleed the front brakes on a 2004 audi a4 quattro?


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. (On my car y have 288 mm). After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Oct 01, 2009 | 2004 Audi A4

2 Answers

Changed front brake pads. brake pedal goes to floor. no brakes


Something doesn't sound right, you shouldn't have to remove the brake line to install pads. Did you have to do this on both sides? Do the new pads and the old pads look the same? Did you get the caliper on crooked? Just recheck your work first before replacing more parts. When you install the caliper, You have to hook the pad on one side first before you slide it over the rotor.

Mar 26, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Brakes


All you have to do is take the calipers off crack open the bleeder of the side you are working on leave the old pad in the caliper and press the pad in as far as it will go tighten bleeder clean the rotors with brake clean to get the oily substance off they put on during shipping to keep them from rusting put rotor back in place and put new pads in caliper if they give you grease for the caliper sliders put some on the caliper bolts and sliders the thing the bolts go into on the caliper so they move fairly easy this way your brakes will work better and last longer put caliper back in place tighten caliper bolts snug usually with a ratchet like a good 3/8 ratchet then do the other side fill up the master cylinder with proper brake fluid usually dot3 but should say on master cylinder cap bleed brakes if you did just the front bleed the passenger side first pump pedal a few times dont go all the way to the floor have someone open the bleeder on the right front passenger front while holding pedal down with just a little pressure one foot on pedal one under pedal so it dont go to the floor then do the same for the other side check fluid start vehicle if pedal is good go for a test drive and thats it.

Jan 06, 2009 | 2005 Ford F-150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85108 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...