Question about 2001 Jeep Grand Cherokee

1 Answer

P1762 Funny, I found that you can check the error code on the dash (ODB) so i did this and received a code of P1762 ("GOV Pressure Sen Offset Volts Too Low Or High"). I was told that this means that I will need to replace the governor pressure sensor, which is located in the governor body on the valve body transfer plate. Do you know if this is true and if so, is it easy to do myself?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had the same problrm a couple weeks ago I ended up replacing the governor pressure sensor and the solenoid it is very easy you just drop the pan and it is right there. Here is a website that shows you how to do it http://forums.minnesotamud.com/showthread.php?p=48356

Posted on Feb 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trouble code p1762


Code p1762 is the governor pressure offset volts too high or too low. This is a transmission solenoid that probably needs replaced. I believe that you have to take the pan off to get at it.

Apr 13, 2014 | 2001 Dodge Dakota

1 Answer

Getting two Codes P1757 and P1762.


P1757--Governor pressure above 3 psi in gear with 0 mph
P1762--Governor pressure sensor offset volts too low or high

Jun 04, 2011 | 2001 Jeep Cherokee

2 Answers

What does codes p1757 an p1762 on 2001 grand cherokee mean


P1757 - Governor Pressure Above 3 PSI When Request Is 0 PSI

P1762 - Governor Pressure Sensor Offset Improper Voltage

Both codes are refered at the governor pressure sensor; I am 99% certain that is bad. Just replace it. Check the voltage on the Light Green/White wire at pin 29 in the white PCM connector with key ON, engine OFF (KOEO). It should be about 0.5-0.7 volts.

If higher than 0.8 volts, check the Transmission Temperature sensor reading on a scan tool. If the Transmission Temperature sensor reads normal, the sensor ground is OK. If the sensor ground is OK, then replace the Governor Pressure sensor.

Hope this helps.

Feb 03, 2011 | 2001 Jeep Cherokee

1 Answer

I have a code p1762 for my 97 jeep grand cherokee


Trouble code P1762 means: Governor pressure sensor offset improper voltage. Gov. Pressure Sensor.It is located in the valve body of the transmission and requires dropping the transmission pan to replace. Sounds much more difficult than it is. Since you have to change your fluid it's a good idea to change the trans. filter .

Feb 01, 2011 | 1997 Jeep Grand Cherokee

1 Answer

Code p1762 govenor pressue sensor offset volts


P1762 1T CCM 1996-2003 Cherokee, Grand Cherokee A/T Governor Pressure Sensor Offset Volts Too High/Low Conditions: Key on or engine running. Gear selector in Park or Neutral. PCM detected an out-of-range Governor Pressure Sensor signal for 1.3 seconds. The fault must occur 3 times on one trip to set a code. Possible Causes: Governor pressure Sensor VREF (5v) circuit is open Governor pressure Sensor ground circuit is open P/N switch is damaged or has failed (not operating properly) Transmission fluid has excessive debris or it is contaminated PCM has failed

Dec 14, 2010 | 2001 Jeep Grand Cherokee

1 Answer

I need to know what diagnostic code p1762 means


Dodge: Governor pressure sensor offset improper voltage Dodge: Governor pressure sensor offset improper voltageFault Code P1762: Automatic transmission Governor pressure sensor offset improper voltage

Sep 30, 2010 | Dodge Pickup Cars & Trucks

2 Answers

Fault codes p1757 p1762 when i doing smoke for dmv when i doing smoke test this code show fault on transmision


CODE P1757 - GOVERNOR PRESSURE GREATER THAN 3 PSI WHEN REQUESTED TO BE O. CODE P1762 - GOVERNOR PRESSURE SENSOR OFFSET VOLTS TOO LOW OR HIGH.MEANING SENSOR INPUT GREATER OR LESS THAN CALIBRATION FOR 3 CONSECUTIVE NEUTRAL PARK OCCURANCES.

Sep 01, 2010 | 2000 Jeep Cherokee

1 Answer

P1762 code for jeep


Gov pressure sensor offset voltage too low or high

Jul 31, 2010 | 2003 Jeep Grand Cherokee

1 Answer

I have a code that i would like identified p1762


P1762 - Gov Press Sen Offset Volts Too Low or High

Jun 30, 2010 | Dodge B Series Cargo Cars & Trucks

1 Answer

P1762


Looks like the fautl code refers to the stuck solenoid on the shift control valve which is in the valve body.
It is a job that requires lots of precision and probably if you take the valve body out you'll need a plan to reassemble it...I would suggest getting it to a specialist.
Cheers

Feb 02, 2009 | 2000 Jeep Cherokee

Not finding what you are looking for?
2001 Jeep Grand Cherokee Logo

1,031 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...