My garage door stopped, just out of sight in the rearview mirror-the brake light section above the rear window now has a lot of broken clips-yes, I hit the garage door --- it stays on, but. should I try to remove it? or duct tape it until I get to a garage?

7-BATT MAIN 1
60A
Fuses: •
CIGAR/DLC/APO FRT
• CLUSTER BATT
• CTSY LAMP
• ON STAR
• PWR LOCK
• PWR MIRROR
• RAP RELAY
• RR PWR SCKT

look below for above listed componet's , pull those fuse's one at a time till arc stop's ,then you found your problem circuit . Do you know where the I/P fuse box is ?
Fuse Block- I/P
Right side of the I/P, in the right front door opening


Fuse Block-I/P Label
Fuse Block-I/P Application Table Fuse/Circuit Breaker
Rating
Description
BCM PRGRM
10A
Body Control Module (BCM)
ENHANCED EVAP/AWD
15A
Evaporative Emission (EVAP) Canister Vent Solenoid, Clutch Pump Check Valve
CIGAR/DLC/APO FRT
20A
Auxiliary Power Outlet-Front, Cigar Lighter, Data Link Connector (DLC)
CLUSTER/BATT
10A
Instrument Panel Cluster (IPC)
CRUISE
10A
Cruise Control Module (CCM), Cruise Control Release Switch, Cruise Control ON/OFF Switch
CTSY LAMP
10A
Body Control Module (BCM)
DRL
10A
Daytime Running Lamps (DRL) Control Module
HVAC/DIC/DRL/HEATED SEAT
10A
Air Temperature Actuator-Left, Air Temperature Actuator-Right, Daytime Running Lamps (DRL) Control Module, Driver Information Center (DIC), Mode Actuator, Rear Window Wiper/Washer and Multifunction Switch (Heated Seat Switch), Recirculation Actuator, Relay Block (Rear Window Defogger Relay)
ELC/TRAILER
25A
Auto Level Control (ALC) Air Compressor, Auto Level Control (ALC) Air Inflator Relay, Auto Level Control (ALC) Sensor
FRT HVAC HI BLWR
30A
Blower Motor Resistor Assembly
FRT WPR/WSHR
25A
Windshield Wiper Motor, Windshield Wiper/Washer Switch
HAZARD
15A
Turn Signal/Multifunction Switch
HEADLAMP
20A
Daytime Running Lamps (DRL) Control Module, Headlamp Dimmer Switch, Headlamp Switch
HTD MIRROR
10A
Outside Rearview Mirrors-Left, Right
HVAC/BLOWER
25A
HVAC Control Module
IGN1
10A
Body Control Module (BCM), Instrument Panel Cluster (IPC), Left Rear Side Door Actuator Control Module, Rear Object Sensor Control Module, Right Rear Side Door Actuator Control Module, Stop Lamp Switch
LH HEADLP HIGH
10A
Headlamp High Beam-Left
LH HEADLP LOW
10A
Headlamp Low Beam-Left
LH T/LP
10A
Tail Lamp-Left, Trailer Rear Wiring Harness
MALL/CLUSTER
10A
Body Control Module (BCM), Instrument Panel Cluster (IPC)
ON STAR
5A
Vehicle Interface Unit (VIU)
PASS KEY
10A
Theft Deterrent Control Module
PCM/ABS
10A
Electronic Brake Control Module (EBCM), Fuse Block-Underhood, Powertrain Control Module (PCM), Park/Neutral Position (PNP) Switch
PCM/CRANK
10A
Powertrain Control Module (PCM)
PCM/PASS KEY/CLUSTER
10A
Instrument Panel Cluster (IPC), Powertrain Control Module (PCM), Theft Deterrent Control Module, Instrument Panel Cluster (IPC), Powertrain Control Module (PCM)
PWR LOCK
20A
Body Control Module (BCM)
PWR MIRROR
10A
Outside Rearview Mirror Switch
PWR QTR VENT
10A
Auto Level Control (ALC) Air Compressor, Auto Level Control (ALC) Sensor, Rear Quarter Window Switch
PWR/HEATED SEAT PSD
30A
Driver Seat Assembly, Passenger Seat Assembly
PWR SLDG DR
30A
Left Rear Side Door Actuator Control Module, Right Rear Side Door Actuator Control Module
PWR WDO
30A
Window Switch-Driver, Window Switch-Front Passenger
RAP RELAY
10A
Relay Block (RAP Relay)
RH HEADLP HIGH
10A
Headlamp High Beam-Right
RH HEADLP LOW
10A
Headlamp Low Beam-Right
RR HVAC/TEMP CONT
25A
Air Temperature Actuator-Auxiliary, Blower Motor-Auxiliary, Blower Motor Relay-Auxiliary, HVAC Control Assembly-Auxiliary, Mode Actuator-Auxiliary
RR DEFOG/ HTD MIRROR
30A
Window Defogger Relay-Rear
RR FOG LP
10A
Fog Lamp Relay-Rear
RR PWR SCKT
20A
Auxiliary Power Outlet-Rear
RH T/LP
10A
Tail Lamp-Right, Trailer Rear Wiring Harness
RR WPR/WSHR
20A
Window Wiper Motor-Rear, Rear Window Wiper/Washer and Multifunction Switch
SIR
15A
Inflatable Restraint Sensing and Diagnostic Module (SDM)
STOP LAMP
15A
Stop Lamp Switch
SWC BACKLIGHT
2A
Steering Wheel Controls-Left, Right
T/SIG
10A
Turn Signal Switch and Backup Lamp Relay

Usually it is in the drivers window controller.There is a module that usually goes bad.

Thanks filter4991;
1. Press and hold button on car's rearview mirror
2. Press and hold button on garage door opener's remote control.
3. Light on Rearview mirror will flash rapidly.
4. Release both buttons.
5. Locate learning button on garage door opener (generally this can be found by tracing the antennae to where it is attached to the unit.)
6. Press and release "Learning button"
7. Press and release rearview mirror button repeatedly until garage door opens/closes but it should work the first or second time.

Worked on Genie Intellicode and Hyundai Tuscon

Although the fault may be in the mirror itself (like a switch), wiring and connector is above the headliner, and that is what you need to check.

Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal

1. Disconnect battery ground cable (14301).
   

1. Remove front door trim panel (23942). Refer to Section 01-05.
   

1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
   

1. Remove two screws from cover assembly.
   

1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
   

1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.
   

Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal

1. Remove cover behind inside door handle.
   

1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
   

1. Remove three screws retaining front door trim panel to front door.
   

1. NOTE: Do not attempt to remove more than one pushpin at a time.
   
   Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
   

1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
   

Installation

1. Follow removal procedure in reverse order.
   

1. Replace all pushpins with new pushpins (N808994-S).
   

Front Door Trim Panel

The replacement of outside rearview mirrors is straight-forward and can be done in an hour or so. If you need new power mirrors, first shop with local body parts suppliers in your area. The after-market mirrors are nearly identical and can be purchased for about $20-$30 per side. Remove the plastic triangular cover over the inside of the mirror by lifting up at base and then release clip at the top which is an upward motion off of a slot in the rear of the triangle. Then pull out the foam insulation carefully. The 3 nuts are 10mm and a long scket works best. For the one at the very front, you will have to use an open end wrench to loosen the nut. There is not much room for a socket. Be carefull to not drop the nuts down the inside of the door, because you don't want to remove the door panel and then the inner metal panel to get them out. If you lose them, buy new ones or replace with proper treaded ones in your garage. After the three nuts are off you need to disconect the wiring. Stop here and make sure you have enough slack in the wiring to be able to hold the female end securely, while you refit your new mirror. I took a piece of wire an dwrapped it around the female end to keep it within reach to re-attach the wiring after the nuts are tightened. Then just replace your foam insulation, and install the triangular cover and you're all set.

remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation

1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
   

1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
   

1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
   

1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
   

1. To install reverse Removal procedure.
   

------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation

1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove front door trim panel (23942). Refer to Section 01-05 .
   

Trim Panels, Door Front—Town Car
Removal

1. Snap out two door pull strap retaining screw covers. Remove screws.
   

1. Remove three screws on front and rear side and center of front door trim panel (23942).
   

1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.
   
   Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
   

1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.
   
   Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
   

1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
   

1. Remove the door trim panel.
   

1. Disconnect two electrical connectors.
   

1. Remove nut from outside rear view mirror mounting base.
   

1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
   

1. Remove screw from outside rear view mirror base.
   

1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
   

1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-
   

Remove the door handle bezel.Remove the power window/door lock switch bezel.Remove the rearview mirror fastener trim cover.Remove the 4 door trim panel retaining screws.One that was behind the mirror trim cover,behind the switch panel,behind the door handle bezel,and one at the bottom corner.Lift the door trim panel up from the door to disengage the trim panel clips.Remove the front radio speaker. Disconnect the power mirror wiring connector.Remove the 3 bolts to the mirror.

When you open the driver's side door, it is located on the side of the dash. Just pry the cover off with a screw driver. There should also be a diagram in the cover

also check your owners manual, you should be hable to find the programing information there.