Question about 1999 Dodge Durango

1 Answer

Please help me

How do i remove the top ball joint out of a 1999 dodge durango

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 512 Answers

They are a need to cut the rivots off and drive the rivots out they will be replaced by bolts.

Posted on Feb 01, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

2000 Dodge Durango: Loud popping sound near front wheels when braking, or going over a bump, turning into or backing out of driveways.

That sounds like the ball joints. The midsized Dodge is notorious for bad ball joints because the factory used substandard parts. I would not wait to have it repaired. There are documented cases of the Dodges losing the front wheels because of ball joint failure. You need to have them repaired asap. The lower ball joints are usually the noisy ones. If you can afford it, have all four fixed at the same time, But be sure to take care of the lowers right away. Hope this has been of some help.

Dec 27, 2010 | 2000 Dodge Durango

1 Answer

1999 dodge Durango upper and lower ball joints. It has 104,000 miles. Where can I buy cheap.

either autozone, oreillys, or advanced auto, the all have a cheaper line and the more expensive moog ones.

Oct 26, 2010 | 1999 Dodge Durango

2 Answers

I thought the rear u-joint was going bad on my front driveshaft, but after removing it from the vehicle, determined it was the ball joint located kinda between the two rear u-joints. I've removed the...

The part you are describing is called a ball stud weld yoke and it has to be machined off the tubing and replaced. A qualified drive line shop should be able to help you with this.

If you have any questions give me a call 619-275-0150


Aug 17, 2010 | 1999 Dodge Durango

1 Answer

How do u replace balljoints on 99 durango

you must remove the spindle to do them ,this means breaks and rotors have to come out,front axle nut has to come out and axle pushed in then remove ball joint nuts and remove spindle.

Jan 20, 2010 | 1999 Dodge Durango

1 Answer

How do I remove the lower ball joint from the control arm on a 2000 Dodge Durango

You'll need a joint puller (looks like a big tuning fork). Depending on how it's held on there, you may also need a ring puller, or you may just need to remove the arm and use an impact driver to pound it out. You may even need to replace the whole arm assembly. The uppers on my Tbird are like this.

Jun 14, 2009 | 1999 Dodge Durango

1 Answer

Cant get ball goints to last longer than a month on a 99 durango they pop extremly loud and it wears tires out bad and thoughts on how to fix ball joint problems and i have tried many brands and many times...

Not trying to critique, but it sounds like they're not being installed correctly, and the front end alignment being done, is not correct.

(The front end is being aligned, after the ball joints are installed, RIGHT?)

Jun 12, 2009 | 1999 Dodge Durango

1 Answer

99 dodge durango needs ball joints

Well if you get an alignment after you put the new ones in you should be alright. As far as these new ball joints they probably just come pre-pressed on the arms and if thats the case then you will have to mess with the coil springs in which case you will need a special tool and you will have to align it all just right or you will have problems later on, i would just stick with the unpressed ball joints also make sure u have something to press them with like a heavy duty vise or a press itself don't use a hammer cause this will damage them.

Mar 19, 2009 | 1999 Dodge Durango

1 Answer

Remove lower ball joint

if you go to a parts store they have a tool that you can rent to remove and replace the ball joints. the rent is just a deposit and you get all the money back when you bring it back.

Jul 23, 2008 | 1999 Dodge Durango

Not finding what you are looking for?
1999 Dodge Durango Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides