Question about 2005 Hyundai Tucson

1 Answer

Bleeding the slave cylinder

How do i bleed the clutch master and slave cylinder properly

Posted by on

  • gwalsh31 May 15, 2009

    tanks john,i tried that and it does b alright for a while then it goes back to the way it was.wud it b there is still air in the system.it is only hard to get the car in first and reverse an also goin down the gears.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 286 Answers

Hi

Best to get the help of a friend to pump the clutch pedal for you.

Take care with the brake fluid, as it removes paintwork !

Top up your clutch fluid reservoir, connect a bleeding tube to the nipple on your slave cylinder, and put the other end of tube in a container.

Get your friend to pump pedal 3 times, and then hold to the floor.

Open the nipple for 5 seconds or so, then close.

Repeat this about 6 to 8 times topping up the fluid as you go.

You should then find, that the air is out of your system, and your pedal is back to normal !

Good luck !

A FixYa rating would be nice.... Thank you ! John.



Posted on Feb 10, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to bleed master clutch cylinder on a 1988 chevy s10


Bleed master first and then slave get tube on bleed nipple and keep pumping into bottle keeping tube in fluid in bottle so it will not draw air on return stroke some cars can be quite hard too bleed

Nov 18, 2015 | Cars & Trucks

1 Answer

I have a 1988 f350 diesel i replaced the clutch master cylinder and the slave cylinder bled the lines and the truck still wont go in gear the throw out arm is moving about 1/2 inch what could be my prob


Ford has special bleeding and blocking instructions for clutch slave. Check manual for proper bleeding requirements. May consider presurre bleeding of master cylinder or use master cyclinder bleeding tubes that fill the resevoir as you bleed the and remove all air in system.

Jan 21, 2013 | Cars & Trucks

1 Answer

Clutch master cylinder gone do i also have to change slave cylinder due to bleeding problems 1999 Grand voyager


No need to change the slave cylinder, but bleed both and if you have low or no brakes then bleed the brakes too.

Jan 08, 2013 | Cars & Trucks

3 Answers

Why does clutch leak off and wont go into gear 96 toyota tacoma when you push on clutch pedal goes to the floor it wont engage clutch to be able to put into gear


the most likely reason is either the clutch master cyl. needs to be replaced.or the.slave cyl. its mounted down on the transmation under the hood find the resivore for the clutch. check the fluid level.if its low , fill it back up , and look for signs of a leak
you will probally have to bleed out all of the air from the system.its done almost the same way as bleeding the brakes. Good Luck.

Nov 05, 2011 | Cars & Trucks

2 Answers

My clutch seems to have gone out tonight. The clutch is very easy to push to the floor...and it pops back....there's no pressure at all. The clutch fluid is leaking from the hose. Could this be the...


it could be either the master cylinder or the slave cylinder,it could also be the clutch pressure plate check the master & slave cylinders first because if it's the pressure plate the gear box will have to be removed to replace the pressure plate, even if you are uncertain it is most likely cheaper to replace the master & slave cylinders than it would be to replace the pressure plate.....hope this helps......cheers.

Aug 31, 2011 | Saturn Vue Cars & Trucks

2 Answers

My 1996 Chevrolet K3500 Dually has a hydraulic clutch, how do I change the fluid and bleed it.


FIRST REMOVE ALL OLD FLUID FROM CLUTCH MASTER CYLINDER YOU CAN USE A SIPHON YOU HAND PUMP.AUTO PARTS STORES SELLS THE HAND PUMP SIPHONS. THEY DONT COST MUCH AND KEEP FROM MAKING A MESS.SIPHON OUT MUCH AS YOU CAN THE OLD FLUID IN THE CLUTCH MASTER CYLINDER.THEN POUR IN THE NEW FLUID DOT 3 BRAKE FLUID IN CLUTCH MASTER CYLINDER.OKAY YOU NEED A HELPER.LOCATE THE SLAVE CYLINDER.REMOVE SLAVE CYLINDER HOLD SLAVE CYLINDER 45 DEGREES WITH BLEEDER SCREW LOCATED AT THE HIGHEST POINT.HAVE A SMALL DRAIN PAN UNDER SLAVE CYLINDER.HAVE HELPER FULLY DEPRESS AND HOLD THE CLUTCH PEDAL THEN OPEN BLEED SCREW.CLOSE THE BLEED SCREW AND HAVE HELPER RELEASE THE CLUTCH PEDAL.REPEAT THIS PROCESS UNTIL ALL THE OLD BRAKE FLUID AND AIR BUBBLES LEAVES THE HYDRALIC SYSTEM AND WHEN YOU CAN SEE GOOD STREAM CLEAN FLUID NO BUBBLES YOU HAVE GOOD SOLID CLUTCH ALL IS GOOD.MAKE SURE THROUGH THE BLEEDING PROCESS YOU DONT LET CLUTCH MASTER CYLINDER RUN DRY OR YOU WILL HAVE TO START OVER.KEEP CLUTCH MASTER CYLINER FULL BRAKE FLUID WHILE DOING THE WHOLE BLEEDING AND FLUSHING PROCESS.

Jan 22, 2011 | 1996 Chevrolet C/K 3500

1 Answer

Are the brake master cylinder and the clutch slave cylinder interconnect in some way? I'm told that the slave cylinder get its fluid from the master cylinder.


The brake system and the clutch master cylinder have the same fluid tank, look at the brake master cylinder fluid tank, on the right hand side about half way up is a hose that goes over to the clutch master cylinder, if fluid level is not above this hose the clutch will stop functioning. If the clutch slave cylinder, mounted on the front side of transmission bellhousing, leaks then the clutch will stop functioning. The slave cylinder has a bleed screw, check these items and fill and bleed as neccessary. Hope this helps, let me know.

Jul 28, 2010 | 1995 Ford Escort

1 Answer

Changed clutch but unable to bleed the slave cylinder. Does that mean clutch master cylinder is bad? Got one from parts store but can't figure out how to take the clutch safty switch off to change it. Any...


Probably not. Bleeding clutch slave cylinders is tricky because you cant "pump it up". The master cylinder has no static valve so the best way to bleed the slave cyl. is to use gravity. Fill the master cylinder reservoir and open the bleed valve on the slave cyl. Allow fluid to drip into an open can until there's no trace of air. Close bleed valve and try clutch. If still no pedal, repeat the process. This is quite an acceptable procedure.

Mar 22, 2010 | 1991 Chevrolet S-10

3 Answers

2001 Ford ranger edge. The gears won't change.


The trans will need to come out. While your at it, just replace the clutch assembly, rear main oil seal, resurface the flywheel, and the clutch master cyl. Its not really a job you should do, find a repair shop to handle it.

Nov 06, 2009 | Ford Edge Cars & Trucks

1 Answer

Clutch pedal stays 2 the floor on a hydralic clutch system on a 2000 camaro v8. clutch master cylinder is new also slave cylinder and clutch and pressure plate


Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.

Sep 06, 2009 | 2000 Chevrolet Camaro

Not finding what you are looking for?
2005 Hyundai Tucson Logo

646 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

69114 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6817 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...