Question about 1994 Ford Econoline

1 Answer

BOTH THE FRONT AND THE REAR ABS WARNING LIGHTS ARE ON CONSTANTLY.

IT'S 1992 FORD F - 250 4X4

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

Clean the rearbrakes sensors

Posted on Mar 08, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to reset brake lite on my 2005 X type jaguar?


which brake warning light is on? the xtype does not have pad wear sensors fitted. so i guess you mean the abs light or the handbrake light.more than likely its the abs light and the common problem is the reluctor rings on one or the other of the rear outer constant velocity joints corroded/ fell off get the fault codes out of the abs module to help.

Aug 22, 2015 | 2005 Jaguar X-Type

2 Answers

2004 ford explorer abs light constant and 4x4 blinking any ideas?


According to the manual pg 10. http://www.fordservicecontent.com/Ford_Content/catalog/owner_guides/04expog3e.pdf
Anti-lock brake system: If the ABS light stays illuminated or
continues to flash, a malfunction has been detected, have the system
serviced immediately. Normal braking is still functional unless the brake warning light also is illuminated.

Apr 16, 2014 | 2004 Ford Explorer XLT

1 Answer

ABS warning light ON; brake pedal sinks to floor when applied; total loss of braking.


Your ABS light is on because the system detected a failure in the brake system. Sounds like either your master cylinder is bad or one of your brake lines has ruptured. Usually a master cylinder seal will degrade over time, not insantly. In a dual master cylinder configuration like all newer vehicles, you should still have some braking, even if a front or rear line ruptures. 1st step, check your fluid level.

Mar 31, 2014 | 2006 Ford F 350 Super Duty

1 Answer

Ford taurus 1996 3.0 ABS ligth on


Hello, These warning lights are pretty accurate. Autozone, Advance, and Oreillys give free scans although the engine system and brake system can require different scanners.

Check your brake fluid level first. The ABS system requires sensors which require counting the revolutions of each wheel. Sometimes the sensors may break, but they can be blinded by dust and debris.

If you have a broken brake pad, the warning light can come on. Often the Emergency brake pad, inside the rear Rotor, can fall apart and trigger an ABS warning.

You need to inspect both the front and rear brakes or take your car to a brake shop for evaluation. Sometimes you can get a free estimate, and some shops can charge for inspecting the Emergency brakes because of the work needed to reach them.

Jul 07, 2011 | 1996 Ford Taurus

2 Answers

I need a radio wiring diagram


Constant 12V+ Green/Purple

Switched 12V+ Yellow/Black

Ground Black/Light Green

Illumination Light Blue/Red

Dimmer n/a

Amplifier Remote Blue

Antenna Right Front

Front Speakers 5" x 7" Doors

Left Front (+) Orange/Light Green

Left Front (-) Light Blue/White

Right Front (+) White/Light Green

Right Front (-) Dark Green/Orange

Rear Speakers 5" x 7" Rear Doors

Left Rear (+) Gray/Light Blue

Left Rear (-) Tan/Yellow

Right Rear (+) Orange/Red

Right Rear (-) Brown/Pink

best wishes

Jan 01, 2011 | 1992 Ford Explorer

1 Answer

1999 Lincoln Navigator ABS warning light turns on?


One of the ABS sensor's is bad or a hub bearing is bad.Could be front or rear.

Jun 23, 2009 | 1998 Lincoln Town Car

1 Answer

Problem with my cruise control and ABS light on 03 Explorer


Anti-Lock Control —Vehicles Built After 03/2002 The 3-channel anti-lock brake system consists of the following components:
  • front wheel speed sensors
  • front wheel speed sensor rings
  • hydraulic control unit (HCU)
  • Anti-lock brake control module (ECU)
  • rear wheel speed sensor
  • rear wheel speed sensor rings
  • yellow anti-lock brake warning indicator
The 4-channel anti-lock brake system with traction control and stability assist system consists of the following components:
  • active brake booster with integral solenoid
  • brake booster release switch
  • front wheel speed sensors
  • front wheel speed sensor rings
  • hydraulic control unit (HCU)
  • stability assist module (ECU)
  • stability assist event indicator
  • lateral accelerometer
  • longitudinal accelerometer (4x4)
  • rear wheel speed sensors
  • rear wheel speed sensor rings
  • steering wheel position sensor
  • yaw rate sensor
  • yellow anti-lock brake warning indicator
  • brake pressure transducer
  • traction control switch
---------------------------------------------------------------------
I suspect the abs issue is causing the speed control not to work if it happened at the same time the cruise control stopped working. When the yellow ABS light comes on, it means the ABS is dactivated. You may have a faulty accelerometer which senses acceleration and yaw (side to side lean). I have not seen a bad one but you said it is sensitive to acceleration.
I would unplug it and see what happens. The connector should have a small tab to depress so you can pull the connector out.
Here is where it is:

Accelerometer Removal and Installation
  1. NOTE: The accelerometer is located under the center, rear passenger seat carpet. (I think you have to remove seat for access).
    Cut the carpeting along the perforations.
  1. Disconnect the electrical connector.
  1. Remove the nuts and remove the accelerometer.
cd31596.gif
Have dealer hook up tester and pull fault codes if you can't find an easy solution.
Some background info
  • A malfunction in the anti-lock brake system will cause the anti-lock brake control module to shut off or inhibit the system. However, normal power-assisted braking remains.
  • Malfunctions are indicated by the yellow ABS warning indicator in the instrument cluster.
  • The anti-lock brake system is self-monitoring. When the ignition switch is turned to the RUN position, the anti-lock brake control module will carry out a preliminary self-check on the anti-lock electrical system indicated by a three-second illumination of the yellow ABS warning indicator in the instrument cluster.
  • During vehicle operation, including normal and anti-lock braking, the anti-lock brake control module monitors all electrical anti-lock functions and some hydraulic operations.
  • Each time the vehicle is driven, as soon as vehicle speed reaches approximately 20 km/h (12mph), the anti-lock brake control module turns on the pump motor for approximately one-half second. At this time, a mechanical noise may be heard. This is a normal function of the self-check by the anti-lock brake control module.
  • Pedal pulsation coupled with noise while braking on loose gravel, bumps, wet or snowy roads is normal and indicates correct functioning of the anti-lock brake system.
  • Warning Lamp Indicator
    The anti-lock brake system (ABS) uses the yellow ABS warning indicator to alert the driver of a malfunctions in the ABS.
    The yellow ABS warning indicator will come on to warn the driver that the ABS has been turned off due to a symptom that exists in the ABS. Normal power assist braking remains but wheels can lock during a panic stop while the yellow ABS warning indicator is illuminated.

    -----------------------------------------
    Please report back, I am curious if that is what it is. Good luck

    Mar 03, 2009 | 2003 Ford Explorer

    4 Answers

    ESP and warning lights on Peugeot 407


    abs esp warning light coming on peugeot 407

    Feb 15, 2009 | Peugeot 407 Cars & Trucks

    1 Answer

    Abs light stays on


    i believe you have to have the computers code cleared....try unhooking the battery for 10 minutes......that should clear out the computer.....if not bring to autozone or the local shop that runs odbc2 and tell them to clear the code.

    Feb 11, 2009 | 1992 Ford F250

    Not finding what you are looking for?
    1994 Ford Econoline Logo

    Related Topics:

    90 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    yadayada
    yadayada

    Level 3 Expert

    64034 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21990 Answers

    Fordexpert

    Level 3 Expert

    5331 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...