Question about 1989 GMC C1500

1 Answer

What size bolts are on the idel arm on an 89 gmc k2500

Need to know what size bolt on ider arm

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

Size 17 mm > please rate my response thank you very much

Posted on Feb 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the torque specs and sequence for the intake and head gasket on a 1999 Chevy Silverado 6.0l V8 K2500


Cylinder Head Bolts (First Pass all M11 Bolts in Sequence)
30 N?·m
22 lb ft
Cylinder Head Bolts (Second Pass all M11 Bolts in Sequence)
90 degrees
Cylinder Head Bolts (Final Pass all M11 Bolts in Sequence-Excluding the Medium Length Bolts at the Front and Rear of Each Cylinder Head)
90 degrees
Cylinder Head Bolts (Final Pass M11 Medium Length Bolts at the Front and Rear of Each Cylinder Head in Sequence)
50 degrees
Cylinder Head Bolts (M8 Inner Bolts in Sequence)
30 N?·m
22 lb ft
Intake Manifold Bolts (First Pass in Sequence)
5 N?·m
44 lb in
Intake Manifold Bolts (Final Pass in Sequence)
10 N?·m
89 lb in
Intake Manifold Wiring Harness Stud
10 N?·m
89 lb in

Oct 27, 2015 | Cars & Trucks

1 Answer

How do you change the ignition coil


Should not be so hard if know what you doing.some goes on spark plug one small bolt,some on side have two small bolts.

Feb 21, 2015 | 1985 GMC K2500

1 Answer

What's what size bolt do I need for a 89 Diahau charade bellhousing?


We have no reference material to look that up

Remove one bolt ,measure its diameter in inches
& divide by .0395 to convert to metric bolt size

Oct 03, 2012 | 1989 Daihatsu Charade

1 Answer

I need to know the torque specs for the head gasket for a 99 2.2 pontiac sunfire


Install cylinder head bolts finger-tight. New cylinder head bolts are recommended due to stretch of the old bolts.
Tighten bolts in sequence, tighten the long bolts to 46 ft. lbs. (63 Nm) plue 90 degrees. Tighten the short bolts to 43 ft. lbs. (58 Nm)


Install pushrode and rocker arms and rocker arm nuts. Tighten nuts to 22 ft. lbs. (30 Nm).


Install valve cover and tighten bolts to 89 inch lbs. (10 Nm).

Apr 05, 2011 | 1999 Pontiac Sunfire

1 Answer

Calgary.cacannot find the right starter bolt for 93 gmc k2500 6.5 turbo diesel truck first one broke shop fixed it with different bolt shorter and fatter they said something about a rivet too that one is...


You will probably have to drill and tap the hole. Before you do this ... consider a helicoil repair. http://www.noblefix.com/helicoil.htm

Your mechanic should be familiar with this or similar product.

Thanks for your question today.

Mar 02, 2011 | 1993 GMC Sierra K3500

2 Answers

What are the torque measurements for the rocker arms and intake manafold?


2.2L Engine & 2.4L Engines
These engines are not equipped with rocker arms. The camshafts directly actuate the valves.

3.1L Engine & 3.4L Engines
When install or connect the check the following:
- Pushrods and the rocker arms. Torque the bolts to 24 ft. lbs. (32 Nm). - Rocker arm cover using a new gasket. Torque the rocker cover bolts to 89 inch lbs. (10 Nm).
- Heater bypass pipe. Torque the screw at the water pump to 106 inch lbs. (12 Nm), the bolt at the cylinder head corner to 18 ft. lbs. (25 Nm) and the nut to 18 ft. lbs. (25 Nm).


About the INTAKE MANIFOLD...
-
Intake manifold nuts and bolts and tighten to 89 inch lbs. (10 Nm)
- Pushrods and rocker arms. Torque the bolts to 89 inch lbs. (10 Nm) plus an additional 30 degree turn. - Lower intake manifold. Apply sealant to the threads of the bolts and torque the bolts to 115 inch lbs. (13 Nm).



859cdc3.jpg

Exploded view of the upper and lower intake-3.1L & 3.4L engines


fe92b8b.jpg

Fig. Lower intake manifold tightening sequence-3.1L & 3.4L engines

Hope help.

May 04, 2010 | 2000 Pontiac Grand Am GT

1 Answer

Need to know how to replace lower control arm


LOWER CONTROL ARM

REMOVAL
1) Raise and support vehicle. 3) Remove the steering knuckle.
Remove the bolts fastening the power steering cooler to the front suspension cradle crossmember reinforcement (Fig. 21). 5) Remove the lower control arm rear bushing retainer bolts located on each side of each lower control arm rear bushing. NOTE: The bolts fastening the cradle crossmember reinforcement are of three different thread sizes. Note the location of the various sizes.

6) Remove the bolts attaching the cradle crossmember reinforcement to the front suspension cradle crossmember (Fig. 22). Remove the 2 bolts fastening the reinforcement and rear of cradle crossmember to the body of the vehicle. Remove the reinforcement. 7) Remove the pivot bolt attaching the front bushing of the lower control arm to the front suspension cradle crossmember. 8) Remove the lower control arm.

Sep 25, 2009 | 2006 Dodge Caravan

1 Answer

I have a 2000 Passat and going to have my friend replace the rotors and breaks. I am preparing to fix it but want to know what sizes are the bolts for the calipers sliding pins. If you know the Bolt s


For a wrench or for the acctual bolt size.
To remove front pads..you need 8mm allen socket to pull the caliper guide pins, then 17 or 18mm..To remove rear pads...you need 13mm socket for lock bolt on guide pins and 15mm open end wrench (thin section to hold guide pin while you remove lock bolts..I ground down a spare wrench). You DO NOT have to remove rear carriers to change rotors..just remove lock screw and angle rotor out. The B5 Passats don't have the electronic parking brake so you don't need VAG Com to change pads.
Installation tips:
Clean and regrease the guide pins with "synthetic caliper grease"
Rear lock bolts come with preapplied thread locker and "are not to be reused"..I just wire brush the threads and use some Loctite Blue on em. I smear just a little antisieze on the inside bore of the rotors and on the lock screw threads to prevent corrosion and make next rotor change ez. Torques:
Front caliper guide pins:18 ft lb
Front carrier bolts: 89 ft lb
Rear guide pin lock bolts:26 ft lb
Wheel lugs: 89 ft lb

May 29, 2009 | 2000 Volkswagen Passat 4Motion

1 Answer

Need the bolt size for 1991 gmc truck cab mount


Check out this website, they have your bolt an much more. Good luck Curt
http://www.lmctruck.com/icatalog/cd/full.aspx?page=25

Mar 16, 2009 | 1991 GMC C1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...