Question about 2002 Ford SVT Focus

1 Answer

Replace rear wiper motor on ford focus 02 plate

Can you tell me step by step how to replace my rear wiper motor. it has stopped working and a friend tested the fuses and it is not that, so have sourced a used motor to replace the broken one with from an auto spares place. many thanks

Posted by on

  • Anonymous Mar 20, 2014

    Found the reason for the failure - a corroded hot lead to license plate lamp separated & shorted to GND.
    I can't find a blown fuse other tha #2.43 - Rear Wiper.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Any auto parts store sells a chiltons manual on your ford focus!!! i think they are around $12 dollars it will explain step by step instructions..........................

Posted on Feb 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is it my 2008 chevy uplander rear wiper motor/blade moves some and stops. I let van set 5-10 minutes with key off. Turn on key. Wiper motor/blade moves a few degrees and then stops again. Why?


Can you move the wiper by hand ? Which does your vehicle have ?
WDA/Z88 The rear wiper is controlled based on an input from the rear wiper/washer portion of the multifunction switch. When closed, the wiper ON and wiper DELAY switches provide a unique voltage signal to the rear window wiper motor indicating the desired speed. Each switch has a unique resistor that drops the voltage to a specified value which is interpreted by the rear window wiper motor as ON or DELAY. The rear wiper motor receives B+ voltage from the I/P fuse block and accessory voltage from the body control module (BCM).
W49 The rear wiper is controlled based on an input from the rear wiper/washer switch. When closed, the wiper ON switch provides a voltage signal to the rear window wiper motor indicating rear wiper operation is requested. The rear wiper motor receives B+ voltage from the I/P fuse block and accessory voltage from the body control module (BCM).
Do you know how to do electrical testing ?
WDA/Z88
  1. Ignition OFF, disconnect the harness connector X1 at the multifunction switch.
  2. Ignition ON, verify a test lamp illuminates between the ignition circuit terminal 4 and ground.
  3. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal, refer to Power Mode Mismatch.

  4. Ignition OFF, connect the harness connector at the multifunction switch. Disconnect the harness connector at the rear window wiper motor.
  5. Test for less than 20 ohms between the ground circuit terminal B and ground.
  6. ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

  7. Ignition ON, verify a test lamp illuminates between the B+ circuit terminal A and ground.
  8. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.

  9. Verify a test lamp illuminates between the ignition circuit terminal E and ground.
  10. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

  11. Rear wiper switch in the ON position, test for B+ between the signal circuit terminal D and ground.
  12. ?‡'
    If less than the specified value, test the signal circuit for an open/high resistance. If the circuit tests normal, test or replace the multifunction switch.

  13. Rear wiper switch in the DELAY position, test for B+ between the signal circuit terminal D and ground.
  14. ?‡'
    If less than the specified value, test or replace the multifunction switch.

  15. If all circuits test normal, test or replace the rear window wiper motor.
W49
  1. Ignition OFF, disconnect the harness connector at the rear wiper switch.
  2. Ignition ON, verify a test lamp illuminates between the ignition circuit terminal 6 and ground.
  3. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal, refer to Power Mode Mismatch.

  4. Ignition OFF, connect the harness connector at the rear wiper switch. Disconnect the harness connector at the rear window wiper motor.
  5. Test for less than 20 ohms between the ground circuit terminal B and ground.
  6. ?‡'
    If greater than the specified range, test the ground circuit for an open/high resistance.

  7. Ignition ON, verify a test lamp illuminates between the B+ circuit terminal A and ground.
  8. ?‡'
    If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.

  9. Verify a test lamp illuminates between the ignition circuit terminal E and ground.
  10. ?‡'
    If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance.

  11. Rear wiper switch in the ON position, verify a test lamp illuminates between the signal circuit terminal D and ground.
  12. ?‡'
    If the test lamp does not illuminate, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, test or replace the I/P switch assembly.

  13. If all circuits test normal, test or replace the rear window wiper motor.
Component Testing

Do you know how

Jun 09, 2016 | 2008 Chevrolet Chevrolet Uplander LS

1 Answer

Cadillac Deville 99


Wiper/Washer System (Pulse) Schematics (w/o CE1)
Wiper/Washer System (Pulse) Schematics (w/CE1)

Which one does yours have ?

The switch could be bad or the windshield wiper / washer module . Do you own a DVOM - digital volt ohm meter ? Do you know how to do automotive electrical trouble shooting ? There are a few good videos on youtube on basic electrical trouble shooting an how to read wiring diagrams . Go to http://www.bbbind.com/free_tsb.html for free wiring diagrams . Check B+ voltage at the switch (in an out ) at the different speeds .Check for B+ voltage at the wiper washer module , it's part of the wiper motor .
The windshield wiper/washer system consists of a permanent-magnet depressed-park wiper motor assembly, a wiper transmission assembly, wiper arm and blade assemblies, a washer pump mounted on a washer solvent container, and a wiper/washer switch assembly.
The wiper/washer system is a pulse (delay) type. Pulse timing and demand wash functions are controlled electronically. Wiper/Washer System Description (Rainsense)
The windshield wiper/washer system consists of a Rainsense module, a permanent-magnet, depressed-park wiper motor assembly, a wiper transmission, wiper arm and blade assemblies, a washer pump mounted on a washer solvent reservoir, and a wiper/washer switch assembly.
The wiper/washer system is a rain sensing type. Rainsense functions are controlled electronically. 1
Was the Wiper/Washer System Check performed?
--
Go to Step 2
Go to Wiper/Washer System Check

2
Inspect the WIPERS fuse A9 for an open.
Is the fuse open?
--
YES - Go to Step 3
NO - Go to Step 4

3
Replace the WIPERS fuse.
Is the replacement complete?
--
Go to Wiper/Washer System Check
--

4
Disconnect the wiper/washer switch connector C202.
Turn ignition switch ON.
Connect a test light from connector C202, terminal E5 to ground.
Is the test light on?
--
YES - Go to Step 16
NO - Go to Step 5

5
Connect a test light from Accessory Relay, terminal A1, to ground.
Is the test light on?
--
YES - Go to Step 6
NO - Go to Step 11

6
Connect a test light from Accessory Relay, terminal A3, to ground.
Is the test light on?
--
YES - Go to Step 7
NO - Go to Step 12

7
Connect a test light from Accessory Relay, terminal B1 to terminal A3.
Is the test light on?
--
YES - Go to Step 8
NO - Go to Step 15

8
Inspect CKT 143 for an open or poor connection between connector C202 and the Accessory Relay.
Was an open or poor connection found?
--
YES - Go to Step 9
NO - Go to Step 10

9
Repair the open or poor connection in CKT 143.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

10
Replace the the Accessory Relay.
Is the replacement complete?
--
Go to Wiper/Washer System Check
--

11
Repair the open in CKT 1040 or the power feed circuit to the WIPERS fuse.
Is the repair complete?
--
Go to Wiper/Washer System Check
--

12
Inspect the ACC fuse C13 for an open.

let me know if you make it this far an then I will send the rest of testing procedures !

Mar 09, 2016 | Cadillac DeVille Cars & Trucks

1 Answer

Why is my windshield wipers running in the off position, it's like they are running in the intermittent position, but it's in the off position.


When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Schematic Reference: Wiper/Washer Schematics


1

Did you review the Wiper/Washer System Description and Operation and perform the necessary inspections?
Go to Step 2
Go to Symptoms - Wiper/Washer Systems

2

  1. Turn the ignition ON.
  2. Turn the windshield wiper/washer switch OFF.
Are the windshield wipers always on?
Go to Step 3
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems

3

Disconnect the windshield wiper/washer switch connector.
Are the windshield wipers always on?
Go to Step 4 if yes
Go to Step 7 if no

4

  1. Disconnect the windshield wiper motor connector.
  2. Test the windshield wiper switch signal 1 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 5

5

Test the windshield wiper switch signal 2 circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 6

6

Test the windshield wiper motor high speed circuit for a short to voltage. Refer to Circuit Testing and to Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 9

7

Inspect for poor connections at the windshield wiper/washer switch. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 8

8

Replace the windshield wiper/washer switch. Refer to Windshield Wiper and Washer Switch Replacement - On Vehicle in Steering Wheel and Column.
Is the repair complete?
Go to Step 11
--

9

Inspect for poor connections at the windshield wiper motor. Refer to Testing for Intermittent Conditions and Poor Connections and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10

10

Replace the windshield wiper motor. Refer to Windshield Wiper Motor Replacement .
Is the repair complete?
Go to Step 11
--

11

Operate the system in order to verify the repair.
Did you correct the condition?
The Wiper / Washer System consists of the following components:
?€¢
Windshield wiper / washer switch


?€¢
Windshield wiper system module / motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
Instrument panel cluster (IPC)


?€¢
ACC 15-amp fuse


?€¢
WSW 30-amp fuse

Jan 04, 2016 | 2002 Pontiac Bonneville

1 Answer

Rear wiper stopped


Do you know how to use a volt meter ? Need to check for voltage at the motor ! , need a wiring diagram. Most of the time other people on here will tell you to check the fuse's , that doesn't end up being the cause ! Most of the time it's the motor or a wiring problem ! I have seen the wire in side the rubber boot ,when you open the rear hatch break causing a no power situation to the motor . If you open the rear hatch ,door ,lift gate , what ever you call it . If you look when it is open there is a rubber boot connecting the body to the door , there are wires in side . There have been known to break ! This next part is a FORD pinpoint test. This is how ford says how to check !
PINPOINT TEST B: THE WIPERS ARE INOPERATIVE - REAR WINDOW Test Step Result / Action to Take B1 CHECK CIRCUITS CBP43 (GY) AND SBP19 (BU/RD) FOR VOLTAGE
  • Key in OFF position.
  • Disconnect: Rear Wiper Motor C476.
  • Key in ON position.
  • Measure the voltage between rear wiper motor C476-3, circuit CBP43 (GY), harness side and ground; and between rear wiper motor C476-4, circuit SBP19 (BU/RD), harness side and ground.
    >
  • Are the voltages greater than 10 volts?
Yes
GO to B2 .

No
VERIFY SJB fuse 43 (5A) and fuse 19 (25A) are OK. If OK, REPAIR the circuit(s) in question. TEST the system for normal operation. B2 CHECK CIRCUIT GD150 (BK/WH) FOR OPEN
  • Key in OFF position.
  • Measure the resistance between rear wiper C476-1, circuit GD150 (BK/WH), harness side and ground.
    >
  • Is the resistance less than 5 ohms?
Yes
GO to B3 .

No
REPAIR the circuit(s) in question. TEST the system for normal operation. B3 CHECK THE MULTI-FUNCTION SWITCH
  • Key in OFF position.
  • Disconnect: Multi-function Switch C202.
  • Carry out the multi-function switch component test. Refer to Wiring Diagrams Cell 149 for schematic and connector information.
  • Did the multi-function switch pass the component test?
Yes
GO to B4 .

No
INSTALL a new multi-function switch. REFER to Section 211-05 .

Mar 14, 2015 | 2010 Ford Expedition EL

1 Answer

Rear wiper doesnt work on my 51 plate focus


Start by checking your fuses. Then put your ear against the wiper arm and have a friend turn it on. if you hear humming then the motor is bad and needs to be replaced. If all else fails check for voltage at the motor. there should be 3 wiree. One will have voltage all the time with the key on, one should be switched voltage and the last will be ground.

Jun 02, 2012 | 2001 Ford Focus

1 Answer

Wind screen wipers and central locking on x 5 suddenly don't work on x5 (rear wipers still work )


you may have two problems or they are both related, the first step would be to check all your fuses, then if fuses are good then test for power at motor to see if the motor is bad or the switch, you will need a test light to do this, turn power on to wipers and then test for power at motor.

Oct 29, 2010 | BMW X5 Series Cars & Trucks

1 Answer

Rear wiper is not working. i have cleaned it and


check the wireing with a test light if that dosent tell you any thing you might need to replace motor or see if its connected to the motor

Apr 02, 2010 | 2007 Chevrolet Uplander

1 Answer

My rear wiper has stopped working on kia sportage 2006. can hear switch ok and fuse ok, how do i remove trim to get to rear wiper motor


Test for power at motor.


Test for power at motor. If you have power, then replace.wiper motor. trim should be held on with panel clips that can be removed with a special panel removal pliers






if

Mar 11, 2010 | 2002 Hyundai Santa Fe

2 Answers

The windshield wipers do not work on my Jaguar XJR 2002. Could be the fuse but i do not know which fuse it is as i do not have an owners manual. Maybe the motor is bad, but I wanted to check the fuse...


I have a 1999 XJ8. Same setup as yours, with very minor differences. I had the same problem, turned out NOT to be fuse, OR bad relays, OR wiper motor, OR Body Processor Module. It was simply a loose connection at the body processor module below the Glovebox. I Literally jiggled the wires, and it started working again, and has been ever since. I have the Shop Manual, Technical ability, and Tools available to test all of the circuits involved, and went forth with printing out the wiring diagrams, and step by step eliminated each, until I decided to give the connection a jiggle, JUST BEFORE replacing the Body Processor Module (which would have been expensive)

Test 1:
Try the jiggle trick. Should be able to access harness just below, and behind the left of the glovebox. touch around up there, but don't be a brute, as you MAY break stuff.

Test 2:
Check Fuse under hood, (#22) Should be a 30A fuse

Test 3:
Swap the relays located on the drivers side, just behind the radiator. One is for Wiper motor run, the other is for wiper motor high speed.

Test 4: Jumper Pin 3 & 5 on the LEFT relay (drivers left) (please remove relay first). This should turn the wipers on, regardless of whether or not the computer is telling it to run. If wiper does not turn on, check fuse, or replace wiper motor.

That's all I've got.... Hopefully this works for you.

Feb 22, 2009 | 2004 Jaguar XJR-Series

Not finding what you are looking for?
2002 Ford SVT Focus Logo

839 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

69114 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Ron Lankford

Level 3 Expert

5383 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...