Question about 1996 Jeep Grand Cherokee

1 Answer

How do you replace a window regulator ?

In a 1996 Jeep Grand Cherokee, Drivers side door

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

First you need to take the inside mirror off just pops off/ second look for pop outs in the panel for screws/ Then you need to pop out bottom of door then sides then pull up on trim and out/ then disconnect switches take of vapor barrier look inside you will see 2or 3 bolts holding it in take them out have someone hold up glass replace then put it back togehter/ Please rate my response thank you very much

Posted on Feb 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Drivers side window on a 2005 Jeep Grand Cherokee falls off track


Have to remove the inner door panel,
to see the problem
Most likely a broken window regulator

Jul 13, 2013 | 2005 Jeep Grand Cherokee

2 Answers

Window on right side dont work on 2002 jeep grand cherokee


if its electric a fuse could be bad or a shortage in the wiring

Nov 06, 2012 | 2002 Jeep Grand Cherokee

1 Answer

Replacement Front, Driver Side Window Regulator


first these are easy to do,second look on ebay a-1 auto I think sells replacement for around $100 U.S
Take door panel off,there are several bolts in reg and 2 keepers on the window glass unhook the 2 keepers unplug the motor and turn unit and bring out the bottom of the doorthe window glass does NOT have to come out. it should only take less than an hour to do.

Sep 24, 2009 | 2000 Jeep Grand Cherokee

1 Answer

The drivers side window can be opperated from the drivers side. The passanger side window does not opperate from either side . It appears that the window lock safety swith on the drivers side is not...


If the problem was with the lock you would still be able to raise or lower the window from the drivers seat,most likely the window motor has burned up,I would try pulling the door panel and tap the motor most times they will work for awhile,but ebay has the whole window regulator with motor for 99.00 I had to replace both driver and passenger in my 01 grand cherokee.was a1auto I think on ebay.

Mar 10, 2009 | 1998 Jeep Cherokee

1 Answer

How do you change a window regulator


remove door panel and disconnect the multi plug to the motor .three bolts hold motor on and one bolt top and bottom on the runner/lifter two bolts hold mechanism to bottom of window .shouldnt take more than an hour and that includes a tea break and *** break in the middle

Feb 01, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Power windows and rear doorlock wont work 1994 jeep grand cheroke


check the wiring between the door and the body on the drivers side....there was a problem with it breaking

Jan 26, 2009 | 1996 Jeep Grand Cherokee

2 Answers

1999 Jeep Grand Cherokee Laredo Electrical issues.


the button that pushed in when you close the door could be bad its literally like a $10 part and plugs in and is only held in with one screw. My interior lights used to flash on and off and i replaced that and now good as new, but you would need to figure out which door is doing it by pushing the button in manually

Jan 12, 2009 | 1996 Jeep Grand Cherokee

1 Answer

Replaced drivers side door


You can change the harness from the existing to the new yes . It's not very hard either. No there is no way to use the window in the meantime. If you attempt to force it you will damage the window regulator. I would confirm caution you to be patient installing the harness as the connectos can be a little tricky to undo.

Nov 04, 2008 | 1996 Jeep Grand Cherokee

1 Answer

2001 Jeep Grand Cherokee Laredo....power windows not working, driver side power door lock not working


I have a 2000 Jeep Grand Cherokee the power windows,power seat , door would not lock , and the inside lights would stay one ..i thought it was a fuse problem but no fuses for that ... in the rubber boot between the door and frame ..the was the ground wire was split ... put a **** connector on it everything works great now ....

Jul 18, 2008 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...