Question about 1987 Lincoln Town Car

1 Answer

Need location of vacuum modulator on a 1987 town car

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 659 Answers

If this is for the transmission, there isnt one

Posted on Mar 01, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Located transmission vacuum module at on the car 1997 honda accord

images for transmission vacuum

Vacuum Modulator Service.wmv - YouTube

? 6:00
Dec 19, 2011 - Uploaded by GrumpysTravells How to remove and clean the vacuum modulator air filter. ...Transmission modulator replacement (early GM 4T60-E models) -

Sep 24, 2015 | 1997 Honda Accord

1 Answer

Where is the AC/Heater Control Actuator located?

Hi Joymar, The EATC module is mounted to the heater box under the dash,below the radio,to the right of HVAC controls. access through glove box opening.[remove glove box] look for module with wire & vacuum connections.if you see a linkage arm or rod,those are actuators,follow vacuum lines to control actuator won't cause the fan to run,they control air flow.Automatic temp system modules are known to fail. Best O'Luck

Jun 06, 2015 | 1999 Lincoln Town Car

1 Answer

Wiper control module location

the wipers are controlled by the lighting control module

Apr 10, 2013 | 2000 Lincoln Town Car

1 Answer

I had to chang the engine computer on my 02 town and country. Do I have to take it to chrysler to get it reprogramed for my van?

the town and country has a PCM ( power control module, located in front to the battery ) and a FCM ( front control module located on the front of the relay center next to the battery ) if either module is replaced they need to be programed with a DRBIII, so you will need to see your dealer.

Sep 09, 2011 | 2002 Chrysler Town & Country

1 Answer

Got a 1987 chevy suburban and it wont start and it is getting fuel and cranking over

Check for vacuum leaks and for spark. The most common problem Ive seen is the ignition control module. Those are notorious on the older chevys. It is located on the bottom of the distributor.

Dec 30, 2010 | 1987 GMC Suburban

1 Answer

87 buick century won't shift out of first

The first thing is to check the transmission fluid level, then check the vacuum modulator located out on the side of the transmission, and be certain that the vacuum line is connected to the vacuum modulator, and that the vacuum line also has no leaks and it is connected to an intake manifold vacuum source. If you remove the vacuum line from the vacuum modulator and if there is any transmission fluid is in the vacuum line then the vacuum modulator is faulty and it will need to be replaced.


Sep 21, 2010 | 1987 Buick Century

2 Answers

I have a 1987 crown vic that I purchased, the prev. owner said that they had the O/drive disconnected as they only drove it in town, all the mech. linkage is connected, it only drives in first, so what do...

Just perhaps they didn't know the vacuum modulator either is shot,disconnected or suffering from a broken vacuum hose.Jack up the car and look for the modulator,it's a round cylinder that sticks out of the transmission housing.It has a vacuum hose attached to it.The amount of vacuum your engine creates causes the trans to shift to the next gear.Pull of the vacuum line,take a clean WHITE rag or napkin.Wipe the modulator where the hose was connected and check it for transmission fluid.A white rag will show the red fluid as being red,any other color rag and you won't be able to tell it from motor oil which is light brown in color.Red oil,change the modulator because it's leaking.You can verify it by creating a vacuum at the modulator port.Don't create a vacuum by sucking on the end of a hose,unless you crave the taste of trans oil.Use a vacuum pump.It will hold the vacuum pressure 15 to 20 lbs., no more than that or you can ruin the modulator your self!Now if there's no oil and it holds a vacuum trace the vacuum line and look for leaks.Connect your pump to the line and create a vacuum,you'll find that leak in a heartbeat!Good luck!

Dec 09, 2009 | 1987 Ford Crown Victoria

1 Answer

Where is the ecm located on a 1987 Town Car?

it is on the pass side behind the kick panel

Dec 08, 2009 | 1987 Lincoln Town Car

1 Answer

I need a 1987 chevy S10 vacuum hose routing diagram

Go to, become member, will give you repair manual,location of parts,diagrams.

Mar 28, 2009 | 1987 Chevrolet S-10 Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts


Level 3 Expert

77499 Answers


Level 3 Expert

5623 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides