Locked out car locked fob no good lock just turns cant get into car

turns fail. 2003.?
so did not check all fuses first then scan the OBD2 port next
ooops, why skip those?

lots they are what do they all do good and bad.?
well fuses are blown why skip step on, electrics, all fuses checked,
"changed flasher"<<, why say that. then not say turns and hazards fail too or not????? i have a real oem shop manual for this car. USA spec car is it>?
w cant guess countries of VIN to know it
chapter 8w wiring, is clear and easy to read.

8w-60 and 61 locks and windows. schematics and all
not the fuse for windows it runs both sides. F12 , 50amps.
do door locks fail using key fob??????????? any?
F12 also runs door locks but is not bad. only for 1 door.

right door inside lock controls dead?too?
you have a fob
and lots of door controls switches, it is clear which fail and do not
front and rear, both.

the door control modules on this car use COMM buse
called PCI serial bus this car
so commands from any in car button or fob must work and send commands to t the door commanded, via PCI bus.
same goes for windows ,door control modules

bad comms
or the origination command device fails, the FOB or the door buttons afail
all doors have controls do only right side fail and fob too?

try testing at all doors first
and the fob too.
off hand seems PCI bus wires damaged on the right side.

I owned a 1999 XJ, USA, love it. sold it, had too many jeeps.
mine had no VIBER of any kind at all. zero.
I have no idea what viber is? English word?
Is this car still OEM stock or modified.
cant lock door with key and fob both?????
the fob battery is no good at all 24 years old ever.
lost the users guide in the glove box.? it covers all FOB usages
and is a 100% free manual from maker JEEP.

yes door lock solenoids can fail easy, for sure this old
for lock rusty or solenoid bad and weak.
if fuses are good
and lock fails try a new lock solenoid, see rockauto.com

replace the latch or chek latch cables or link from lock cyldr

key in ignition 2 number 2 then press the fob. till doors lock. 2 to 3 times then unlock with fob. turn back key lock car. then un lock. then do the same with the other fob.

1 - Unlock the doors. Put the key in the ignition, and turn from "Off" to "ACC" 8 (eight) times in under 10 seconds. The doors will lock. Leave key in the "ON" position

2 - Program the fobs by pressing any key on the fob. The doors locks will lock/unlock

3 -- Turn the key to Off. Locks will lock/unlock, and you are out of programming mode.

I bought new remote Key Fob on Ebay and it did work properly on my Ford Transit LWB 2003. Good Luck!

In the case the battery was drained in the keyfob - try reprogramming it.
Here are the instructions.

The process is pretty easy....1st) get in the vehicle and close all doors, windows, hood, and trunk.
2nd)put the key in the ignition and turn it to the second position...while in that position (w/out starting) push the lock button on the good key fob you already have. (if you don't already have a good fob, then press the lock button on the new key fob) (do this all w/in 5 seconds)
3rd)turn the key off
4th) turn the key on to the second position and press the lock button on the fob.
5th) turn the key off
6th) turn the key on to the second position and press the lock button on the fob.
7th) turn the key off.
8th) turn the key on to the second position and press the lock button the the fob.....the press the unlock button on the fob..........Now press the lock button on the new fob...press the unlock button on the new fob....
9th) tun the key off.....remove the key from the ignition and test to make sure that the new fob and the old fobs both work now.


Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.

if its a factory alarm you put the key in and quickly turn the key on and of i cant remember if its 8 or 9 times but the horn will chirp then you push the lock and unlock on the fob the locks should respond then turn key off and your done. note that if you have more than one fob you have to press lock and unlock on all of them before you turn the key off and i believe you only have about fifteen seconds to do so if not let me know i will look it up at work

i have a rover 25 and the key fob is not opening the car i could use the key to open it but the alarm will go off and cant stop it without the fob...

You have the wrong KEY if it won't turn any locks.
You can use the KEY fob from another Passat.
The one you have was most likey not the original
and the car was reprogrammed to except that FOB.

The Fuse panel Is inside the DRIVES side.
Open the Driver door. Look at the side of the DAShboard.
THat Giant "B" Shapped plastic cover pops off.

Check the fuses...IF any are broken,black or no good.
REplace them

Hope this helps

Sketchlab.com
MugShot Collection.

need to program key fob to car and program windows...see owners manuel... if cant find ..i can help