Question about 2005 GMC Sierra

1 Answer

4 Wheel Drive Issues

When I first shift into 4 wheel drive and push the gas its like my 4 wheel drive isn't engaging right away. It sounds like its trying but it sounds like the transfer case just isn't catching. It eventually goes in. Sometimes I have to shift in to different gears before it engages. Its a 2005 Sierra

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 56 Answers

Check fluid level in transfer case.

Posted on Feb 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Will not go in to four wheel drive


Dodge Ram 1500 Questions - 4WD not engaging all the ...

www.cargurus.com > Questions > Dodge > Ram 1500

CarGurusOct 18, 2013 - to get it into 4LOW is to 1st get it into HI and then stop and shift it intoLOW. ... I have a 98 Dodge Ram 1500 that I can not get the 4 wheel drive to ... what web site can i go to so i can see how the inside looks on timing gears.

Diagnosing 4WD Engagement Problems on Dodge Ram ...

dodgeram.org > Main > Tech > Maintenance
Nov 1, 2000 - This shift will be easier if you momentarily release the accelerator pedal. Apply a ... Do not attempt to shift to or from 4L while transmission is in gear or clutch is engaged. ... OK, now when you shift into 4WD it gets a little more complicated. .... I have a 97 RAM 1500 Club Cab Sport 4 X4 and I am having

2008 Dodge Ram 1500 Won't Engage 4 Wheel Drive: 20 ...

www.carcomplaints.com/Dodge/Ram_1500/.../drivetrain/wont_engage_4...
Ram 1500 Won't Shift Out Of 4 Wheel Low - Ram got locked into 4 wheel low. Found this ..... It would not go into full time 4 wheel drive or go into 2 wheel drive.

Software Update and Axle Disconnect Actuator ... - RepairPal

repairpal.com > Problems > Dodge > Ram 1500

Feb 08, 2016 | 2004 Dodge Ram 1500

1 Answer

4 wheel drive tries to engage going down the road while shift lever still in 2H


Then you need to check the linkage underneath the floor where it connects to the transfer case, and make sure it isn't loose or mal-adjusted.

Nov 26, 2011 | Chevrolet Silverado 3500 Cars & Trucks

1 Answer

1996 gmc jimmy started making noise sounding like it is is right front was told need to replace wheel hub which was done. Still making the same noise in 2 wheel drive. when you push button for 4 wheel...


Sounds like your front axle is trying to engage but does not engage fully.check your vacuum going to the t-case switch and then if that is ok check your vacuum at the front axle actuator.It is located under the battery tray.

Dec 06, 2010 | 1996 GMC Jimmy

1 Answer

Four wheel drive doesnt engage


Sounds like you have a bad switch.

Apr 21, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

4 wheel drive will not engage 4 wheel drive button is pushed


bad trasfer case selector motor common problem i ve a ton of these replace that motor and youll have 4 wd again ,the part is costly about $ 300.00. hope this helps.

Dec 13, 2009 | 1999 GMC Jimmy

1 Answer

Grinding in and out of 4 wheel drive


You say 'new' truck, 09? or new used? I have had 3 Fords, 3 w/ manual trans. case, if you go into 4x4 Low range, you must come to a complete stop before shifting the trans. case to 4x4 mode, and I always put trans (automatic) in neutral before slipping into 4x4, it engages smoothly, no grinding. 4x4 high range can be put in while moving, but I would let off the gas pedal, shift to 4x4 high range, then resume accelerating. If there is any grinding going on doing it as above, something isn't right. Check the trans. case fluid level also, to make sure that's not an issue.

Aug 15, 2009 | 1998 Dodge Ram 1500 4WD

2 Answers

Front drive, 4 Wheel drive won't engage


that vacume line goes back to the transfer case, the end that goes behind the motor hooks to a steel tube so it does not get hot from the exhaust., my guess it should be hooked up so it will feed vacume to the vacume ball so it can lock in the axels. if you start the car and shift into 4 wheel drive and listen under hood you should hear a hissing sound, that is vacume, if you can't hear it there, you may have to craw under the right side to hear it, probably came unhooked underneith the car

Feb 01, 2009 | 1995 GMC Jimmy

1 Answer

Front wheel will not engage for 4 wheel drive


very possible. Put your jeep on 4 jackstands and put in 4 wheel drive. if the front drive shaft turns pull the vacuum disconnect and check the shift fork. They usually break before the shift actuator.

Jun 28, 2008 | 1992 Jeep Wrangler

Not finding what you are looking for?
2005 GMC Sierra Logo

292 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...