Question about 1992 Mitsubishi Diamante

1 Answer

Timing incorrect I have a 93 Verada (thats what they are called here) 3.0 V6 and the timing is out but the sticker on it says to ground the timing terminal first can you tell me where it is and what to do

Posted by on

  • Mike Butler
    Mike Butler May 11, 2010

    I think the terminal is up near firewall, at rear of engine. Do you see any empty connectors back there?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 56 Answers

On a Right hand drive the timing wire is a brown/orange round connector with a single wire, it is exposed from the main wiring loom that runs along the firewall in the engine bay, on the passenger side of the engine bay, just behind the intake manifold. you may need to look hard for it as from factory they have black tape holing it to the harness, can be seen if looking for it.

Earth this terminal and you can then correctly setup the idle and timing.

Good luck

Posted on Jul 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Installing timing belt on a 93 mazda mpv V6


I would say install as is,you can always reset at 8 degrees if engine won't start.Can you move distrubeter

Nov 26, 2013 | Cars & Trucks

1 Answer

1993 Mitsubishi v6 Verada missing at idle.


Please about the diagnosis and repair of engine misfires here.

Oct 16, 2012 | Mitsubishi Cars & Trucks

1 Answer

Caint see timing marks on 93 ford probe v6 gt


There is some very wrong information here. Do not remove the cap or mess with the rotor! As someone else said, go to probetalk.com jumper the t/en test point to ground to disable the automatic timing adjustment - after that it's pretty standard procedure.

Sep 15, 2011 | 1993 Ford Probe

1 Answer

I have a 93 Mazda mx 3 v6. I HAVE fuel, spark, and compression, timing marks all line up, will crank but not start what will cause this no start condition? Note: I replaced the disty, crank sensor, fuel...


Let me no when u find out cuz I have a 96 mx3 v6 pulling the same **** I got told it's the timing but they look like the line up but if they are even out one tooth it won't start mine try's to start but it won't I fucked my starter from it

Feb 02, 2011 | 1993 Mazda MX-3

1 Answer

Where do you find the engine number for an audi a4 v6 2.8


Hi, is it a 1.8 turbo or 2.8 V6 or 2.7 biturbo V6 ? on most models what you will be looking for is a 3 letter code like ATQ or APW and is normally on a sticker on the timing belt cover, it is also stamped into the engine on a ledge up high. if no luck there check the owners manual, around the 3rd page there will be a sticker that was put in the book during predelivery inspection this sticker is about 3 inches by 3 inches and filled with id codes for almost everything. If the pdi wasn't done right another copy of the same sticker will be under or next to the spare tire in the spare tire well.
Take care

Aug 04, 2010 | 2002 Audi A4

1 Answer

93 camry 3.0L V6 timing belt


A 6 cylinder is an interference fit engine . Chances are you bent some valves IF the belt slipped.
Mounts usually don't make a vehicle shake as you described.
I believe the milage intervalfor timing belts is every 60 thousand.
Good luck

May 14, 2010 | 1993 Toyota Camry V6

1 Answer

Changeing the timing belt on a 93 audi v6 engine


you dont need a diagram to see the timing marks on the top/bottom pulleys,just clean them off and run a piece of chalk around the perimeter.they are a bit obvious.....

Apr 02, 2010 | 1993 Audi 100

2 Answers

Engine number location for 2002 audi a4


is it a 1.8 turbo or 2.8 V6 or 2.7 biturbo V6 ? on most models what you will be looking for is a 3 letter code like ATQ or APW and is normally on a sticker on the timing belt cover, it is also stamped into the engine on a ledge up high. if no luck there check the owners manual, around the 3rd page there will be a sticker that was put in the book during predelivery inspection this sticker is about 3 inches by 3 inches and filled with id codes for almost everything. If the pdi wasn't done right another copy of the same sticker will be under or next to the spare tire in the spare tire well.

Mar 24, 2009 | 2002 Audi A4

Not finding what you are looking for?
1992 Mitsubishi Diamante Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...