Question about 2002 Toyota Avalon

1 Answer

2002 license plate bulbs

How do i remove the license plate bulbs from my 2002 toyota avalon? i removed the trunk cover, but i cant figure out how to emove the bulbs to replace.
thanks,
jeff

Posted by on

  • Anonymous Mar 13, 2014

    How do I check to see if it's a fuse or the bulbs itself

  • Anonymous Mar 16, 2014

    Can't Access license plate light holder. is now inside liftgate

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

Its real simple look at the license plates then look up you will see 2 screw per lamp / unscrew them and slide remove its a 194 bulb so get some ready then replace and put back / Please rate my response thank you very much

Posted on Feb 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace license plate blub in 2002 buick lasabre


your going to remove the entire trunk lid assembly from the vehicle. If you open the trunk and look from the inside you should either see black plastic wing nuts or 10mm nuts holding the assembly to the trunk. There will be approximately 10 of them that will need to be removed. Once they are removed the lens assembly will pop away from the trunk lid. The license bulbs can then be replaced. I usually replace all six taillight/license bulbs whenever I have one of these apart. Its the same bulb for all six lights.

Oct 02, 2011 | Cars & Trucks

2 Answers

Help how do i change the license plate bulb on my 2004 corolla?


I just replaced my 2 bulbs an hour ago in my garage.
1. Pry off all the clips that hold the liner. I used a cloth covered spatula, so
as not to chip the paint, to pull out the liner a little bit and used my
index and middle finger to pull back the clip and the liner, very slowly to
prevent breakage. When all the clips are off, the liner will fall, no need
to remove the emergency release handle.
2. Press the tiny release lock that hold the wires in the socket and pull
out the wires, carefully.
3. Turn the socket 1/4 the the left carefully, while putting a little pressure
upward, then the socket will release.
4. Pull the bulb staight out and replace it.
5. Reverse the procedure and voila! A ton of money saved!!!!!!
MVC.

Jan 03, 2011 | Toyota Corolla Cars & Trucks

1 Answer

How to replace license plate lights


    Follow the Steps on how to replace license plate light on your car.

    1. Open the trunk and locate the trunk liner retainer clips.Use the Phillips head screwdriver to loosen the center plastic screw of the retainer clip about 1/4 turn, just enough to raise the head of the screw from the base of the clip. Pull the screw up, and lift the clip out of the liner. Use a flathead screwdriver to help pry it out. Remove enough of the clips to allow access to the license plate light sockets. Pull the liner back.

    2. Remove the emergency trunk release handle by popping off the top cover of the handle. Use the needle nose pliers to gently squeeze the prongs on the shaft, while removing the handle.

    3. Unplug the wire harness from the license plate light bulb socket the release clip on the side of the outlet.Twist the license plate light bulb socket 1/4 turn counterclockwise, using the needle nose pliers again. Do not apply too much pressure to the pliers; you may damage the socket.

    4. Remove the bulb from the socket, and replace it with a new one.

    5. Replace the socket into the socket assembly, and plug the wire harness back in. Test the bulb by turning on the lights of the Corolla, then turn them off again.

    6. Replace the trunk emergency release handle, and replace the hood liner and the retainer clips. Remove the old bulb and tools, and close the trunk.

Dec 22, 2010 | 1995 Toyota Corolla

1 Answer

How do you change the rear license plate light bulbs???


First look under when your license plate lights are and you will see 2 phllips headed screws remove those screws and the license plate light assembly will drop out of the bottom of the trunk, simply twist the blub to unlock it from the light housing pull the bulb straight out of the socket replace it with a new bulb and the installation is the reverse of the removal.

Dec 06, 2010 | 2002 Jeep Grand Cherokee

1 Answer

How do I change the light bulb above the rear license plate?


YOU HAVE TO OPEN THE TRUNK LID REMOVE THE BLACK PLASTIC COVER FOR THE TRUNK LID LATCH.REMOVE THE LICENSE PLATE LIGHT HOUSING FROM THE TRUNK LID.REMOVE THE BULB SOCKET FROM THE LICENSE PLATE LIGHT HOUSING.TO REMOVE BULB FROM THE SOCKET SIMPLY PULL IT STRAIGHT OUT OF THE SOCKET.

May 15, 2010 | 2008 Chevrolet Malibu

1 Answer

How do i replace the license plate lights on my 1990 honda accord. i can't get the bulb out of the socket


You should have two license plate lights, right above the license plate. If you remove the two screws that hold the one you want to change in, the entire fixture will drop down(best to do this with the trunk open). Remove the metal clip plate that covers the bulb. The bulb SHOULD simply pull directly out.
Hope this helps you.

Oct 21, 2009 | 1990 Honda Accord

1 Answer

License plate bulb 99 alero


remove the 2 license lamp screws from outside,above the lic.plate then from insidethe trunk pull up the lic.lamp housing and replace the bulb.it should pull straight out

Apr 21, 2009 | Oldsmobile Alero Cars & Trucks

2 Answers

Bulb burnt out on license plate


you need the remove the lighting fixture first to access the bulbs.

Mar 19, 2009 | 2002 Cadillac Deville

1 Answer

How to replace the license plate blub


open the trunk and remove the back panel in the trunk could be a couple of clips or a few screws holding the panel on one you remove the panel you should have easy access to the bulb just twist and remove. or on some avalons you need to pry the lens off the light to replace it then the lens will click back into place with a little push

Mar 09, 2009 | 2000 Toyota Avalon

2 Answers

License plate bulb on 1997 Cadillac deville


this is straight out of the book ok



  1. Open the rear compartment lid.
  2. Remove the rear compartment lid trim.
  3. Pull back on the rear compartment trim panel.
  4. Unplug the lamp connector from the rear compartment lid wiring harness.
  5. Press the grommet out of the rear compartment lid.
  6. Remove the nuts retaining the lamp assembly to the rear compartment lid.
  7. Remove the bulb.

Mar 07, 2009 | 1997 Cadillac DeVille

Not finding what you are looking for?
2002 Toyota Avalon Logo

548 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...