Question about 1991 Nissan Pickup

1 Answer

Slave cylinder gone

Slave cylinder is gone. How tough is this to replace?

Posted by on

  • rogstar69 Feb 01, 2009

    No it has a hydraulic clutch. Need to replace the cylinder.

  • rogstar69 Feb 01, 2009

    Thanks. I was afraid of that.



1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

Do you mean the Brake Master Cylinder????

Posted on Jan 31, 2009

  • Travis Humphries
    Travis Humphries Feb 01, 2009

    It is not that Hard to Replace But, You will need to Bleed the Clutch. That is always the Big Problem on these. They are Really hard to Bleed Correctly without the Bleeder Tools. You might want to get it done or you might be back here asking how to get it Bled Properly. I have never been able to get one Done in a Driveway. Please Rate My Response! Thanks!

  • Travis Humphries
    Travis Humphries Feb 01, 2009

    No Problem



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Whats happened when clutch has jus gone all lose an theres no tightness there anymore hyuandi 98 excel

You start with the master & slave cylinder,
any cables,etc & hopefully the transaxle doesn't
have to come out

Mar 09, 2013 | Hyundai Excel Cars & Trucks

1 Answer

Clutch slave cylinder wont come up to presure

If the master cylider and slave cylinder have been rebuilt and they won't hold, it sounds like there is an internal leak in one end of the system.
Could be a damaged (cracked) cylinder where the rubber cup will not seal.

Aug 19, 2012 | Hyundai Tiburon Cars & Trucks

2 Answers

My clutch seems to have gone out tonight. The clutch is very easy to push to the floor...and it pops back....there's no pressure at all. The clutch fluid is leaking from the hose. Could this be the...

it could be either the master cylinder or the slave cylinder,it could also be the clutch pressure plate check the master & slave cylinders first because if it's the pressure plate the gear box will have to be removed to replace the pressure plate, even if you are uncertain it is most likely cheaper to replace the master & slave cylinders than it would be to replace the pressure plate.....hope this helps......cheers.

Aug 31, 2011 | Saturn Vue Cars & Trucks

2 Answers

I just replaced the clutch, pressure plate, throwout bearing and both the master and slave cylinders. I am not getting any significant travel in the slave when I push the pedal in. How much travel should...

you may just open the bleeder, and let it gravity bleed. make sure on the master cylinder that the piston is coming all the way back when the pedal is all the way back/up. there's an adjustment for that, on the rod connecting the clutch pedal to the master cylinder.

Dec 21, 2010 | Isuzu Trooper Cars & Trucks

1 Answer

Clutch pedal droped raisded back by hand pedal does not depres engine does not start

It sounds like your clutch master or slave cilinder has gone bad .you should be able to locate clutch cylinder under hood usually drivers side check fluid level if low replace master or slave cylinder.

Nov 26, 2010 | 2004 Hyundai Santa Fe

1 Answer

My clutch is comletely gone. I added brake fluid, but it leaked out. How do I fix the leak?

Sounds like your slave cylinder is leakingout the fluid and needs to be replaced. The slave cylinder is the hydralic part that pushes on the clutch, when you depress the clutch pedal. Have it inspected and replaced if necessary.

Oct 11, 2010 | 1992 Jeep Wrangler

2 Answers

I need a clutch master cylinder. The shop said the book says it will take 3.5 hours to do the job. Can this be true?

If you replace both the master and slave cylinder [and I would due to the age of the vehicle] then it is the correct time. The slave cylinder is the easy one but the master cylinder can be tough on this vehicle.

Aug 26, 2010 | 1991 Mitsubishi 3000GT

1 Answer

97 honda Ex Accord Standard Transmission. Having problem shifting into 1st or reverse when starting up car. while going down road it shifts fine. week prior same problem, told son to check fluid level,...

problem is in the hydraulic clutch system
low fluid indicates a leak at the slave cylinder and not holding pressure indicates a leak at the slave cylinder or in the clutch master cylinder
If the master cylinder and slave cylinder have not been replace in side 5 years ago , the have them replace by a specialist brake and clutch shop
at this point there is nothing wrong with the clutch proper

Nov 27, 2017 | 1997 Honda Accord

3 Answers

2001 Ford ranger edge. The gears won't change.

The trans will need to come out. While your at it, just replace the clutch assembly, rear main oil seal, resurface the flywheel, and the clutch master cyl. Its not really a job you should do, find a repair shop to handle it.

Nov 06, 2009 | Ford Edge Cars & Trucks

Not finding what you are looking for?
1991 Nissan Pickup Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

77499 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides